EC-LINK EC-RF620 Dual Channel RFID Controller User Manual
- October 30, 2023
- EC-LINK
Table of Contents
- EC-LINK EC-RF620 Dual Channel RFID Controller
- Product Information: EC-RF620 Dual-channel RFID controller
- Product Features
- Product Usage Instructions
- Product Features
- Interface definition
- Install the sizing diagram
- Installation accessories
- Technical data
- FCC STATEMENT
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
EC-LINK EC-RF620 Dual Channel RFID Controller
Product Information: EC-RF620 Dual-channel RFID controller
The EC-RF620 Dual-channel RFID controller is a product of EC-LINK Automation (Shenzhen) Co. Ltd. It is a compact device with dimensions of 132X87X35mm and has a protection level of IP67. The device has a working power supply of DC 9V-36V2A and a maximum power consumption of 8W. It has a working temperature range of -25 to +70 degrees Celsius and a storage temperature range of -40 to +85 degrees Celsius. The device has a communication interface that includes Ethernet, RS-232, and RS485. It also has IO interfaces andANT1/ANT2 interfaces.
Product Features
- Compact size
- IP67 protection level
- DC 9V-36V2A power supply
- Maximum power consumption of 8W
- Working temperature range of -25 to +70 degrees Celsius
- Storage temperature range of -40 to +85 degrees Celsius
- Communication interface that includes Ethernet, RS-232, andRS485
- IO interfaces and ANT1/ANT2 interfaces
Product Usage Instructions
The EC-RF620 Dual-channel RFID controller can be used in various applications such as access control systems, inventory management systems, and asset tracking systems. To use the device, follow the steps below:
- Mount the device using the DIN Guide rail installation kit or wall set.
- Connect the power supply to the POWER interface using the M12-A 4-pin connector.
- Connect the device to the network using the LAN interface and the M12-D 4-pin connector.
- Connect the antennas to the ANT1/ANT2 interfaces using the SMA connector. Only connect the antennas required to be used. Unconnected antenna, the software does not open, otherwise no-load may damage the reader!
- Connect input/output devices to the IO interfaces using the M12-A 12-pin connector. The interface definition is as follows:
- IN1: Input1
- IN2: Input2
- IN3: Input3
- IN4: Input4
- OUT1: Output1
- OUT2: Output2
- RS232-RXD: RS232 Receive Data
- RS232-TXD: RS232 Transmit Data
- RS232-GND: RS232 Ground
- RS485A: RS485 A
- RS485B: RS485 B
- Power source GND
- The device has 3 LED display lights that indicate the device’s status:
- Red light bright: The device power is ON.
- Blue light bright: Represents data upload (read to tag). No bright means that there is no data upload.
- Greenlight bright: Indicates receiving data. No light indicates that no data is received.
For more information and support, contact EC-LINK Automation (Shenzhen) Co. Ltd. in Room 2206, Block B, Shixia Xintian Century Business Center, Futian District, Shenzhen City. You can also visit their website at www.eclinksz.com or contact them by telephone at 0086-755-8368 1813 or fax at 0086-755-8323 5833. You may also send an email to sales@eclinksz.com.
Product Features
- Operating Frequency: 860MHz~960MHz
- Support Protocol: support EPC class Gen2 (ISO 18000-6-c)、GB/T29768
- Working mode: fixed frequency or frequency jump
- Output power: 1dBm-33±1dBm
- Read-write speed: Greater than 400, times/second
- Read and write distance: Greater than 10 m, related to the antenna and label specifications.
- Working power supply: DC 9V-36V,2A
- Maximum power consumption: 8W
- Working temperature: -25℃- +70℃
- Storage temperature: -40℃- +85℃
- Working humidity: 10% ~ 95% RH without condensation
- Communication interface: Ethernet、RS-232、RS485
- Finished product size: 132X87X35mm
- Installation method: the 4 x M4 screws are fixed
- Protection level: IP67
- Impact and vibration test standards: IEC61373
Interface definition
- POWER interface, The connector meets the standard GJB142A, M12-A 4 pin.
- LAN interface, M12-D 4pin Connector definition.
- ANT1, ANT2 interface, The SMA connector, connecting to the antenna.
- Only connect to the antennas required to be used.
- Unconnected antenna, the software does not open, otherwise no-load may damage the reader!
IO Interface, M12-A 12-pin connector definition
I/O Interface definition
1| IN4 Input4|
Schematic diagram of the wiring port
2| RS485A
3| RS232-RXD
4| RS232-TXD
5| OUT2 Output2
6| OUT1 Output1
7| IN1 Input1
8| IN2 Input2
9| IN3 Input3
10| RS485B
11| RS232-GND
12| Power source
(GND)
Human-computer interface requirements
The controller has 3 LED display lights, specifically defined as follows.
Lights | Definition |
---|---|
PR | Red light bright–The device powered ON |
TX | Blue light bright–Represents data upload (read to tag): No bright means |
that there is no data upload
RX| Greenlight bright–Indicates receiving data: No light indicates that no
data is received
Install the sizing diagram
Installation accessories
- DIN Guide rail installation kit, model:20950000004
Technical data
- Material: Stainless steel
- Accord with RoHS
- Accord with REACH
- Package size: Length 132 mm X width35 mm X
- The thickness of 1.5 mm Net weight: is 82.7 g
Wall set, model: 20 95300 0007
- Material: Stainless steel
- Size: Length 132 mm X width 85.5 mm X height
- 37.5 mm
- Accord with RoHS
- Accord with REACH
- Net weight: 164.1 g
Caution
This device must be professionally installed This equipment does not allow any antenna to work with the transmitter; the permitted antenna type must be specified external antennas, for example (antenna name: Planar RFID antenna, Model: EC-UHF-NF3004) device is generally for industrial/commercial use. it must be sold to authorized dealers or installers only, and cannot be sold via retail to the general public or by mail order. The equipment is an RFID technology RF product and must be installed by electrical and electronic professionals with a professional certificate.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and(2) this device must
accept any interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Mobile device
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
IC Caution.
- CAN ICES-003(B)
- RSS-Gen Issue 3 December 2010
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
ADD: Room 2206, Block B, Shixia Xintian Century Business Center, Futian District, Shenzhen City http://www.eclinksz.com Tel:0086-755-8368 1813 Fax:0086-755-8323 5833 E-mail:sales@eclinksz.com.