Danfoss AQP Teflon Racing Hose Instruction Manual
- October 30, 2023
- Danfoss
Table of Contents
AQP Teflon Racing Hose
Instruction Manual
Aeroquip Performance Products
Assembly Instructions
AQP Teflon® Racing Hose with Reusable Fittings
Racing Hose, Teflon with Reusable Fitting
Step 1. Cut hose square to length with fine-tooth hack saw or cut-off
wheel. To minimize wire braid flare out, wrap hose with masking tape and cut
through tape. Remove tape, trim loose wires and flush with lube before next
step. Burrs on bore of tube should be removed with a knife. Clean the hose
bore.
Sometimes
wire braid hose will “neck down” on one end and “flare out” on the other end.
This can be used to an advantage. Slip two sockets back to back over the
“necked down” end of the hose, position approximately 3 inches from each end.
Mount nipple hex in a vise. Work the hose bore over the nipple to size the
tube and aid in separating the braid prior to fitting the sleeve. Remove hose
from nipple.
Step 2. Push the sleeve over the end of the tube and under the wire braid
by hand. Complete positioning of the sleeve by pushing the hose end against a
flat surface. Visually inspect to see that the tube butts against the inside
shoulder of the sleeve. Set the sleeve barbs into the Teflon tube by pushing
a round nose tapered punch into the end of the sleeve and tube.
Step 3.
Lubricate nipple and socket threads. Use a molydisulfide base lubricant for
stainless steel fittings (e.g. Molykote Type G); lubricants containing
chloride are not recommended. Other material combinations use standard
petroleum lubricants. Hold the nipple with hex in the vise. Push hose over
nipple with twisting motion until seated against nipple chamfer. Push socket
forward and start threading of socket to nipple.
Step 4. Wrench tighten hex until clearance
with socket hex is at .031 inches. Your thumbnail is a convenient measuring
device. Tighten further to align corners of nipple and socket hexes. CLEAN,
PROOF TEST TO TWICE OPERATING PRESSURE AND INSPECT ALL ASSEMBLIES.
To
disassemble: Unscrew and remove nipple; slide socket back on hose by tapping
against flat surface; remove sleeve with pliers.
Important: Fittings may be dis as sem bled and reused at least once.
However, all such fittings should be carefully examined for distortion, thread
damage and I.D. dimensions. New sleeve is recommended upon reuse of fitting.
Compliments of Aeroquip Performance Product team. For for more technical
information please visit
Aeroquipperformance.com
For more information on these and other AQP Performance Products see the
catalog
Aeroquip Performance Products by Danfoss A-SPPE-CC001-E
AN451068216691en-000101
Products we offer:
- Cartridge valves
- DCV directional control valves
- Electric converters
- Electric machines
- Electric motors
- Gear motors
- Gear pumps
- Hydraulic integrated circuits (HICs)
- Hydrostatic motors
- Hydrostatic pumps
- Orbital motors
- PLUS+1® controllers
- PLUS+1® displays
- PLUS+1® joysticks and pedals
- PLUS+1® operator interfaces
- PLUS+1® sensors
- PLUS+1® software
- PLUS+1® software services, support and training
- Position controls and sensors
- PVG proportional valves
- Steering components and systems
- Telematics
Danfoss Power Solutions is a global manufacturer and supplier of high-
quality hydraulic and electric components. We specialize in providing state-
of-the-art technology and solutions that excel in the harsh operating
conditions of the mobile off-highway market as well as the marine sector.
Building on our extensive applications expertise, we work closely with you to
ensure exceptional performance for a broad range of applications. We help you
and other customers around the world speed up system development, reduce costs
and bring vehicles and vessels to market faster.
Danfoss Power Solutions – your strongest partner in mobile hydraulics and
mobile electrification.
Go to www.danfoss.com for further product
information.
We offer you expert worldwide support for ensuring the best possible solutions
for outstanding performance. And with an extensive network of Global Service
Partners, we also provide you with comprehensive global service for all of our
components.
Local address:…………………………..
Hydro-Gear
www.hydro-gear.com
Daikin-Sauer-Danfoss
www.daikin-sauer-danfoss.com
Danfoss
Power Solutions (US) Company
2800 East 13th Street
Ames, IA 50010, USA
Phone: +1 515 239 6000| Danfoss
Power Solutions GmbH & Co. OHG
Krokamp 35
D-24539 Neumünster, Germany
Phone: +49 4321 871 0
---|---
Danfoss
Power Solutions ApS
Nordborgvej 81
DK-6430 Nordborg, Denmark
Phone: +45 7488 2222| Danfoss
Power Solutions Trading
(Shanghai) Co., Ltd.
Building #22, No. 1000 Jin Hai Rd
Jin Qiao, Pudong New District
Shanghai, China 201206
Phone: +86 21 2080 6201
Danfoss can accept no responsibility for possible errors in catalogues,
brochures and other printed material. Danfoss reserves the right to alter its
products without notice. This also applies to products already on order
provided that such alterations can be made without subsequent changes being
necessary in specifications already agreed.
All trademarks in this material are property of the respective companies.
Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights
reserved.