sysform S-700 Electric Corner Cutter Instruction Manual
- October 30, 2023
- Sysform
Table of Contents
sysform S-700 Electric Corner Cutter
Operating Manual
Read this manual before operating the machine. Keep hands away from the clamping and cutting area.
Summary
The Electric Corner Cutter S-700 is an electrically powered machine that is triggered through a clutch. It is designed to cut rounded corners for paper, PVC, and other materials. The machine can cut various specifications of rounded corners, and it is characterized by a sense of control, ease of operation, and maintenance. It is an ideal equipment for the packaging industry. (Refer to Figure 1 for the machine’s structure).
Main Technical Data
The machine has a big table which can be used for cutting various sizes of materials.
- Max thickness of paper: 3.15” / 80mm
- Cutting speed: 130 times/min
- Slide stroke: 3.54” / 90mm
- Blade specification: R3-R13mm
- Rotation of motor: 1400r/min
- Weight: 231.5 lbs / 105Kgs
- Measurement: 22.44” x 24.02” x 55.12” / 570×610×1400mm not including big table
Installation and Operation
The machine has a function for the stroke criteria. If you want the single stroke criteria, you shall step on the timer controller for the foot pedal. Tread on the foot pedal till the flywheel runs for nearly a circle, then step off. But if you tread on the foot pedal, it doesn’t work, and then the slide will continually run.
- The machine shall be installed on the flat floor with the four feet on the floor.
- Add some machine grease to the lubricating parts of machine referring to Figure 1.
- Open the front door, tread on the foot pedal (No.10), manually rotate the major wheel in the anticlockwise direction, observing if the gap between the upper and lower cutter is suitable. If it is not suitable, adjust it according to the following description. Then rotate the major wheel some rounds, observing if the other parts are working normally.
- Turn on the power switch. The indicator lamp for the switch is lighting and the motor is running.
- Tread on the foot pedal（No.10）, observing if the machine is working normally. Particularly check that the machine has no single stroke locking function for the stroke criteria. If you want the single stroke criteria, you shall step on the timer controller for foot pedal. Tread on the foot pedal till the flywheel runs for nearly a circle, then step off. But if you tread on the foot pedal, it doesn’t work, and then the slide will continually run.
Figure 1
- Top screw for blade
- Slide
- Blade upper
- Limit adjusting screw for blade
- Motor
- Clamp
- Side gauge
- Damper
- Adjusting screw for foot pedal position
- Foot pedal
Adjustment
Adjustment for the Blade Upper
The adjustment for the upper blade is to adjust the top and bottom position
for the upper blade. The round arc intaglio of the upper blade should insert
into the lower blade port at 1-2mm. Loosen the three screws on the right of
the slide (See 2 of Figure1). Let the upper blade go up and down to be in the
proper position. After adjustment, tighten the three screws.
Adjustment for the Lower Blade (See Figure 2)
To adjust the gap between the upper and lower blades, refer to Figure 2.
Figure 2
You can adjust the locking screw upper the damper No.8 in Figure 1 in order to have the main shaft keep balance in running and overcome the inheritance at stop for damper function. This screw can be adjusted for time but it shall not be too tight or too loose, or it will lock the main shaft, making it not move.
Adjust Side Gauge
The side gauge can be adjusted by loosening the screw behind it. Then you can
move it randomly. Tighten it after it is well adjusted.
Lubricating
The lubricating points are pointing out in Figure 1. It is recommended to add grease every week.
Usage Instructions
- First, read the operating manual carefully before using the machine.
- Keep hands away from the clamping and cutting area to avoidinjury.
- Install the machine in a safe and stable location before use.
- Adjust the upper and lower blades before use, ensuring they are in the proper position and gap.
- Adjust the side gauge as necessary for your specific project.
- Add grease to lubricating points every week to ensure smooth operation.
- Turn on the machine and step on the foot pedal to start the cutting process.
- After use, turn off the machine and clean any debris or excess material from the cutting area.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>