milwaukee M18 BI Compressor Tyre Inflator Instruction Manual

Milwaukee M18 BI Compressor Tyre Inflator

Product Information

The product is an M18 BI machine, which comes with a battery pack. The user manual contains technical data, safety instructions, working hints, and symbol descriptions. The machine has various buttons and symbols, including a start button, autostop start button, stop button, memory button, and units button. It also has a display that shows the battery level in percentage and pressure units such as BAR, PSI, and KPA. The machine has a maximum pressure of 6 BAR or 87 PSI.

Product Usage Instructions

1. Before starting any work on the machine, remove the battery pack.
2. Check the plug and power cord for any damage before use.
3. Press the ON button to turn on the machine.
4. Press the start button or autostop start button to begin the operation.
5. Press the stop button to stop the operation.
6. Use the memory button to store pressure readings.
7. Refer to the display to monitor battery level and pressure units.
8. Use the units button to switch between BAR, PSI, and KPA pressure units.
9. The machine has a maximum pressure of 6 BAR or 87 PSI.

Functional description

Picture section with operating description and functional description

Remove the battery pack before starting any work on the machine

TECHNICAL DATA

• Type Inflator
• Production code 4835 39 01 XXXXXX MJJJJ
• Battery voltage 18 V ⎓
• Rated input 270 W
• Max. operating pressure 150 PSI; 10,30 bar; 1030 kPa
• Air delivery rate @ 0 PSI / 0 bar / 0 kPa 38,8 l/min
• Pressure hose length 92 cm
• Weight according to EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah … 12,0 Ah) 3,25 … 4,78 kg
• Recommended Ambient Operating Temperature -18 … +50 °C
• Recommended battery types M18B…; M18HB…
• Recommended charger M12-18…; M1418C6
• Noise information: Measured values determined according to EN 60335.
• Typically, the A-weighted noise levels of the tool are:
• Sound pressure level / Uncertainty K 81,89 dB (A) / 1 dB (A)
• Sound power level / Uncertainty K 89,88 dB (A) / 1 dB (A)
• WARNING! Read the instruction manual carefully before using the appliance. Read all safety warnings and all instructions.
• Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
• WARNING: Operators shall be adequately instructed on the use of these machines.
• Save all warnings and instructions for future reference.

INFLATOR SAFETY WARNINGS

• Always wear goggles and ear protection when using the machine.
• Do not leave the appliance unsupervised when it is switched on.
• Never direct any compressed air or blow any dust toward people or animals.
• Do not use the device in rooms with a potentially explosive atmosphere.
• Risk of Bursting. Do not overinflate. Follow all manufacturer‘s instructions for the item. Do not set the tool to an output pressure greater than marked maximum pressure of item to be inflated.
• Never block or plug the air outlet during operation.
• Check air hose for wear or damage before each use. Check all accessory connections are secure.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• Have damage repaired immediately by an authorised workshop.
• Following 10 minutes of continuous operation, a short break of at least 10 minutes must be taken to allow the device to cool down.
• Remove the battery pack before starting any work on the appliance.
• Rechargeable batteries are to be removed from the appliance before being charged; Exhausted batteries are to be removed from the appliance and safely disposed of. If the appliance is to be stored unused for a long period, the batteries should be removed. The supply terminals are not to be short-circuited.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

• WARNING! To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., Can cause a short circuit.
• Never break open battery packs and chargers and store only in dry rooms. Keep dry at all times.
• Use only System M18 chargers for charging System M18 battery packs. Do not use battery packs from other systems.

SPECIFIED CONDITIONS OF USE

• The inflator is intended to inflate items such as car tires, bike tires, lawn equipment tires, sports equipment, air mattresses, beach toys and other inflatables.
• Do not use this tool to fill air tanks or shocks. Do not use this tool as a breathing device. Do not use this tool to spray chemicals.
• Do not use the product in any way other than those stated for intended use.

RESIDUAL RISK

• Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:
• Injury caused by vibration. Hold the product by designated handles and restrict working time and exposure.
• Exposure to noise can cause hearing injury. Wear ear protection and limit exposure.
• Injury due to flying debris. Wear eye protection, heavy long trousers, gloves and substancial footwear at all times.
• Inhalation of toxic dusts.

NOTES FOR LI-ION BATTERIES

Use of Li-Ion batteries

• Battery packs which have not been used for some time should be recharged before use.
• Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating).
• The contacts of chargers and battery packs must be kept clean. For an optimum life-time, the battery packs have to be fully charged, after use.
• To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged.
• For battery pack storage longer than 30 days:
• Store the battery pack where the temperature is below 27°C and away from moisture
• Store the battery packs in a 30% – 50% charged condition
• Every six months of storage, charge the pack as normal.

Battery protection for Li-Ion batteries

• In extremely high torque, binding, stalling and short circuit situations that cause high current draw, the tool will vibrate for about 5 seconds, the fuel gauge will flash,and then the tool will turn OFF.
• To reset, release the trigger. Under extreme circumstances, the internal temperature of the battery pack could raise too much. If this happens, the fuel gauge will flash until the battery pack cooled down. After the lights go off, the work may continue.

Transporting Lithium Batteries

• Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
• Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations.
• The user can transport the batteries by road without further requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.

When transporting batteries:

• Ensure that battery contact terminals are protected and insulated to prevent short circuit.
• Ensure that battery pack is secured against movement within packaging. Do not transport batteries that are cracked or leak. Check with forwarding company for further advice.

CLEANING

• The ventilation slots of the machine must be kept clear at all times.

MAINTENANCE

• Use only Milwaukee accessories and Milwaukee spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses).
• If needed, an exploded view of the tool can be ordered. Please state the Article No. as well as the machine type printed on
  the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.

TROUBLESHOOTING

• If pressure accuracy becomes poor or the inflator’s actual value reads greater than zero when not connected to any object, the pressure sensor may have drifted due to altitude or other factors.

To reset:

• With nothing connected to the inflator, hold the and the Inflation button for 3 seconds to reset the pressure.

SYMBOLS

• Please read the instructions carefully before starting the machine.

• CAUTION! WARNING! DANGER!

• Remove the battery pack before starting any work on the appliance.

• Always wear goggles when using the machine.

• Wear ear protectors.

• Risk of Bursting.

• Do not dispose of electric tools, batteries/rechargeable batteries together with household waste material.
  Electric tools and batteries that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

• Check with your local authority or retailer for recycling advice and collection point.

• Voltage

• Direct Current

• European Conformity Mark

• British Conformity Mark

• Ukraine Conformity Mark

• Eurasian Conformity Mark

• Copyright

• Techtronic Industries GmbH

• Max-Eyth-Straße 10

• 71364 Winnenden

• Germany +49 (0) 7195-12-0 www.milwaukeetool.eu

• Techtronic Industries (UK) Ltd Fieldhouse Lane Marlow Bucks SL7 1HZ UK (09.21) 4931 4259 70 2021

References

• Milwaukee Tool Europe | Cordless Power Tools, Outdoor Tools, Hand Tools, PPE, Work wear. Storage and Accessories. | Milwaukee Tools Europe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>