milwaukee M18 ONEFHIWP12 Cordless Impact Screwdriver Instruction Manual

M18 ONEFHIWP12 Cordless Impact Screwdriver

Product Information

The M18 ONEFHIWP12, M18 ONEFHIWF12, and M18 ONEFHIWF34 are three different models of cordless impact wrenches manufactured by an unknown company. These wrenches come with an interchangeable battery pack, allowing for easy replacement and extended usage time. The product user manual includes technical data, important safety information, working hints, and symbol descriptions for the user’s convenience.

Product Usage Instructions

1. Before starting any work on the machine, remove the battery pack. This ensures safety and prevents accidental activation of the wrench.

2. Check the plug and power cord for any damages before use. Only a specialized technician should repair any faults.

3. Choose the appropriate model of the wrench for the task at hand. The M18 ONEFHIWP12 is a 1/2 inch impact wrench, the M18 ONEFHIWF12 is a 3/8 inch impact wrench, and the M18 ONEFHIWF34 is a 3/4 inch impact wrench.

4. Refer to the picture section of the user manual for an operating and functional description of the wrench.

5. Refer to the text section of the user manual for technical data, safety information, working hints, and symbol descriptions.

6. Press the start button to activate the wrench.

7. Adjust the torque settings according to the needs of the task.
   The wrench has a maximum torque output of 1200 ft-lbs.

8. Use the wrench to loosen or tighten nuts, bolts, and other fasteners.

9. Press the stop button to deactivate the wrench when finished with use.

Product Functional

Functionally Description

Remove the battery pack before starting any work on the machine

TECHNICAL DATA CORDLESS IMPACT SCREWDRIVER M18 ONEFHIWP12 M18 ONEFHIWF12

M18 ONEFHIWF34

Production code……………………………………………………….. ……..4671 85 03… …………… 4671 95 03… ……….. 4672 05 03…
…000001-999999 …000001-999999 …000001-999999

No-load speed ……………………………………………. 0-950 min-1 ……………….0-550 min-1 ………………… 0-800 min-1
Impact range ……………………………………………… 0-1150 min-1 ……………….0-950 min-1 ………………… 0-850 min-1

No-load speed ……………………………………………. 0-1500 min-1 ……………..0-1400 min-1 ………………. 0-1300 min-1
Impact range ……………………………………………… 0-2100 min-1 ……………..0-1750 min-1 ………………. 0-1850 min-1

No-load speed ……………………………………………. 0-1800 min-1 ……………..0-1750 min-1 ………………. 0-1800 min-1
Impact range ……………………………………………… 0-2400 min-1 ……………..0-2100 min-1 ………………. 0-2400 min-1

No-load speed ……………………………………………. ……. 0-1800 min-1 ……………..0-1750 min-1 ………………. 0-1800 min-1
Impact range …………………………………………….. ……. 0-2400 min-1 ……………..0-2100 min-1 ………………. 0-2400 min-1

• Torque max …………………………………..1017 Nm …………………. 1356 Nm …………………….1627 Nm
• Max. diameter bolt / nut ………………..M 24 ……………………….. M33 …………………………..M33
• Tool reception ………………1/2″ (13 mm) …………….1/2″ (13 mm) ………………. 3/4″ (19 mm)
• Battery voltage……………………………………………………………… 18 V ……………………….. 18 V …………………………..18 V
• Weight according EPTA-Procedure 01/2014 (4.0 Ah / 5.0 Ah) 3,2 kg ……………………… 3,3 kg …………………………3,5 kg
• Weight according EPTA-Procedure 01/2014 (9.0 Ah) ………… 3,6 kg ……………………… 3,7 kg …………………………3,9 kg
• Frequency band(s) of Bluetooth ………………………………………2402-2480 MHz ………..2402-2480 MHz …………. 2402-2480 MHz
• Radio-frequency power ………………………………………………….1,8 dBm ………………….. 1,8 dBm ……………………..1,8 dBm
• Bluetooth version …………………………………………………………..4.0 BT signal mode …. 4.0 BT signal mode ………. 4.0 BT signal mode
• Recommended ambient operating temperature ………………….-18 …. +50 °C………….. -18 …. +50 °C ……………..-18 …. +50 °C
• Recommended battery Type …………………………………………..M18B2, M18B4, M18B5, M18B6, M18B9
• Recommended charger Type ……………………………………………………………. M12-18C, M12-18AC, M12-18FC, M1418C6

Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ………………….. 94,7 dB (A) ……………… 94,9 dB (A) ………………….98,5 dB (A)
Sound power level (Uncertainty K=3dB(A)) ……………………….105,7 dB (A) ……………. 105,9 dB (A) ………………..109,5 dB (A)

Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 62841.

Vibration emission value ah
Impact tightening of fasteners of the maximum capacity of the tool……………..18,4 m/s2 …………………. 16,7 m/s2 …………………….15,9 m/s2
Uncertainty K= ………………………………………………………….. …………. 1,5 m/s2 …………………… 1,5 m/s2 ………………………1,5 m/s2

WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

IMPACT DRIVER SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a „live“ wire may make exposed metal parts of the power tool „live“ and could give the operator an electric shock.
Wear ear protectors. Exposure to noise can cause hearing loss.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders.

The dust produced when using this tool may be harmful to health. Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch the device on again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the insertion tool stalled and rectify this, paying heed to the safety instructions.

The possible causes may be:

• It is tilted in the workpiece to be machined
• It has pierced through the material to be machined
• The power tool is overloaded
  Do not reach into the machine while it is running.

The insertion tool may become hot during use. WARNING! Danger of burns

• When changing tools
• When setting the device down

Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning them. Milwaukee Distributors off er to retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects (short circuit risk).
Use only System M18 chargers for charging System M18 battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load or extreme temperatures. In case of contact with battery acid wash it off immediately with soap and water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately seek medical attention.

WARNING: This device contains a lithium button/coin cell battery. A new or used battery can cause severe internal burns and lead to death in as little as 2 hours if swal lowed or enters the body. Always secure the battery cover. If it does not close securely, stop using the device, remove the batteries, and keep it away from children. If you think batteries may have been swallowed or entered the body, seek immediate medical attention.

Warning! To reduce the risk of fi re, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fl uid or allow a fl uid to fl ow inside them. Corrosive or conductive fl uids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., can cause a short circuit.

SPECIFIED CONDITIONS OF USE
The cordless impact wrench can be used to tighten and loosen nuts and bolts wherever no mains connection is available.
Do not use this product in any other way as stated for normal use.

EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulfi lls all the relevant regulations and the directives 2011/65/EU (RoHS), 2014/53/EU, 2006/42/EC, and the following harmonized standards have been used:

• EN 62841-1:2015
• EN 62841-2-2:2014
• EN 55014-1:2017+A11:2020
• EN 55014-2:2015
• EN 62479:2010
• EN 301 489-1 V2.2.3
• EN 301 489-17 V3.1.1
• EN 300 328V2.2.2
• EN IEC 63000:2018

Winnenden, 2021-02-02
Alexander Krug
Managing Director
Authorized to compile the technical fi le.

Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany

GB-DECLARATION OF CONFORMITY

We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulfi lls all the relevant provisions of the following Regulations S.I. 2008/1597 (as amended), S.I. 2017/1206 (as amended), S.I. 2012/3032 (as amended) and that the following designated standards have been used:

• BS EN 62841-1:2015
• BS EN 62841-2-2:2014
• BS EN 55014-1:2017+A11:2020
• BS EN 55014-2:2015
• BS EN 62479:2010
• EN 301 489-1 V2.2.3
• EN 301 489-17 V3.1.1
• EN 300 328V2.2.2
• BS EN IEC 63000:2018
  Winnenden, 2021-02-02

Alexander Krug
Managing Director
Authorized to compile the technical fi le.

Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany

SELECTING MODE
Allow the tool to come to a complete stop before changing modes. Press the selector button to cycle between the settings. Select wireless to change the default settings via the ONE-KEY App on your smart device.

ONE-KEY™
To learn more about the ONE-KEY functionality for this tool, please reference the Quick Start guide included with this product or go to www.milwaukeetool.com/one-key. To download the ONE-KEY app, visit the App Store or Google Play from your smart device.
When the product experiences ESD, the speed LED shuts down and the product cannot adjust speed. It needs the battery and coin cell removed and reinserted to recover .
Also, when the product experiences ESD, the Bluetooth communication will be disconnected. It needs to be reset manually to recover.
We considered the results to be within our minimum acceptable performance level according to EN 55014-2 / EN 301489-1 / EN 301489-17.

BATTERIES
Battery packs which have not been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, after use, the battery packs have to be fully charged.
To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged.

For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% – 50% charged condition Every six months of storage, charge the pack as normal.

BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations that cause high current draw, the tool will vibrate for about 2 seconds and then the tool will turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperatur of the battery could become to high. If this happens, the battery will shut down.
Place the battery on the charger to charge and reset it.

TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations.

• The user can transport the batteries by road without further requirements.
  Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.

• When transporting batteries:

• Ensure that battery contact terminals are protected and insulated to prevent short circuit.

• Ensure that battery pack is secured against movement within packaging.

• Do not transport batteries that are cracked or leak. Check with forwarding company for further advice

MAINTENANCE

Refer to the ONE-KEY App for information regarding necessary servicing.
Use only Milwaukee accessories and spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the machine type printed as well as the six-digit No. on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.

SYMBOLS

CAUTION! WARNING! DANGER!

Remove the battery pack before starting any work on the machine.

Please read the instructions carefully before starting the machine.

Do not swallow the coin cell battery!

Do not dispose electric tools, batteries/rechargeable batteries together with household waste material.
Electric tools and batteries that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
Check with your local authority or retailer for recycling advice and collection point.

n0
No-load speed

V
Volts

Direct current

CE
European Conformity Mark

UKCA
British Confomity Mark

Ukraine Conformity Mark

EAC: EurAsian Conformity Mark

Copyright 2021
Techtronic Industries GmbH Max-Eyth-Str. 10
71364 Winnenden Germany
Tel: +49 (0) 7195-12-0
Website: www.milwaukeetool.eu

Techtronic Industries (UK) Ltd Fieldhouse Lane
Marlow Bucks SL7 1HZ
UK

References

• Track Tools with ONE-KEY™: Free Inventory App by Milwaukee®
• Milwaukee® Tool Official Site | Nothing but HEAVY DUTY® | Milwaukee Tool
• Track Tools with ONE-KEY™: Free Inventory App by Milwaukee®
• Milwaukee Tool Europe | Cordless Power Tools, Outdoor Tools, Hand Tools, PPE, Work wear. Storage and Accessories. | Milwaukee Tools Europe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>