milwaukee M12 FHIR14 Cordless Industrial Screwdriver Instruction Manual

October 30, 2023
Milwaukee

milwaukee M12 FHIR14 Cordless Industrial Screwdriver

milwaukee-M12-FHIR14-Cordless-Industrial-Screwdriver-product-
image

Product Information

This is a cordless industrial screwdriver with two models, M12 FHIR14 and M12 FHIR38. The production codes for the two models are 4830 62 01 and 4830 69 01 respectively. The tool reception size for M12 FHIR14 is 1/4 (6.35 mm) and for M12 FHIR38 is 3/8 (9.5 mm).

Product Usage Instructions

  1. Remove the battery pack before starting any work on the machine.
  2. Before any work on the machine, remove the battery pack and check the plug and power cord for any damage. Repairs should only be performed by a specialist in the field.
  3. Insert the appropriate tool bit into the tool reception of the screwdriver.
  4. Press and hold the start button to begin operation. Release the button to stop.
  5. The screwdriver has four different torque settings, indicated by the percentage of maximum torque: 100%, 75%, 50%, and 25%. Use the appropriate setting for your specific task.
  6. When changing torque settings or removing/inserting tool bits, ensure the screwdriver is not in operation.

milwaukee-M12-FHIR14-Cordless-Industrial-
Screwdriver-12

Remove the battery pack before any work on the machine.

milwaukee-M12-FHIR14-Cordless-Industrial-
Screwdriver-13 milwaukee-M12-FHIR14-Cordless-Industrial-
Screwdriver-14

Handle (insulated gripping surface)

milwaukee-M12-FHIR14-Cordless-Industrial-
Screwdriver-15

TECHNICAL DATA CORDLESS INDUSTRIAL SCREWDRIVER

  • Production code………………………………………………………………………. …………………….4830 62 01… ……………..4830 69 01… …000001-999999 …000001-999999
  • Tool reception ………………………………………………………………………………………………….. 1/4″ (6,35 mm)……………… 3/8″ (9,5 mm)
  • No-load speed ………………………………………………………………………………………………. 0-450 min-1 ………………….. 0-450 min-1
  • Torque max …………………………………………………………………………………………………….. 47,5 Nm ……………………… 47,5 Nm
  • Battery voltage…………………………………………………………………………………………………… 12 V……………………………. 12 V
  • Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah … 6,0 Ah) …………………. 0,96…1,20 kg ………………. 0,96…1,20 kg
  • Recommended ambient operating temperature ………………………………………………………………… -18°C … +50°C
  • Recommended battery types……………………………………………………………………………………………….. M12B…
  • Recommended charger ……………………………………………………………. ……………………………. C12C, M12C4, M12-18…

Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:

  • Sound pressure level (Uncertainty K=3dB(A)) ………………………………………………… 84,26 dB (A) ………………… 84,26 dB (A)
  • Sound power level (Uncertainty K=3dB(A)) ……………………………………………………. 95,26 dB (A) ………………… 95,26 dB (A)

Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 62841.
Vibration emission value ah :

  • Impact tightening of fasteners of the maximum capacity of the tool……………………… 2,88 m/s2 …………………….. 2,88 m/s2
  • Uncertainty K = ……………………………………………………………………… 1,50 m/s2 …………………….. 1,50 m/s

WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

IMPACT DRIVER SAFETY WARNINGS

Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a „live“ wire may make exposed metal parts of the power tool „live“ and could give the operator an electric shock.
Wear ear protectors. Exposure to noise can cause hearing loss.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch the device on again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the insertion tool stalled and rectify this, paying heed to the safety instructions.
The possible causes may be:

  • it is tilted in the workpiece to be machined
  • it has pierced through the material to be machined the power tool is overloaded
  • Do not reach into the machine while it is running. The insertion tool may become hot during use.
  • when changing tools
  • when setting the device down

Chips and splinters must not be removed while the machine is running.

When working in walls ceiling, or fl oor, take care to avoid electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning them. Milwaukee Distributors off er to retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects (short circuit risk).
Use only System M12 chargers for charging System M12 battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load or extreme temperatures. In case of contact with battery acid wash it off immediately with soap and water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to fl ow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., can cause a short circuit.

SPECIFIED CONDITIONS OF USE

The cordless industrial screwdriver can be used to tighten and loosen nuts and bolts wherever no mains connection is available.
Do not use this product in any other way as stated for normal use.

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that the product described under “Technical Data” fulfi lls all the relevant regulations and the directives 2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the following harmonized standards have been used:

  • EN 62841-1:2015
  • EN 62841-2-2:2014
  • EN 55014-1:2017+A11:2020 EN 55014-2:2015
  • EN IEC 63000:2018
  • Winnenden, 2020-10-27
  • Alexander Krug
  • Managing Director
  • Authorized to compile the technical fi le.
  • Techtronic Industries GmbH
  • Max-Eyth-Straße 10
  • 71364 Winnenden
  • Germany

GB-DECLARATION OF CONFORMITY

We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulfi lls all the relevant provisions of the following Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended) and that the following designated standards have been used:

  • BS EN 62841-1:2015
  • BS EN 62841-2-2:2014
  • BS EN 55014-1:2017+A11:2020
  • BS EN 55014-2:2015
  • BS EN IEC 63000:2018
  • Winnenden, 2020-10-27
  • Alexander Krug
  • Managing Director
  • Authorized to compile the technical fi le.
  • Techtronic Industries GmbH
  • Max-Eyth-Straße 10
  • 71364 Winnenden
  • Germany

BATTERIES

Battery packs which have not been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged, after used.
To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% – 50% charged condition Every six months of storage, charge the pack as normal.

BATTERY PACK PROTECTION

In extremely high torque, binding, stalling and short circuit situations that cause high current draw, the tool will vibrate for about 5 seconds, the fuel gauge will fl ash,and then the tool will turn OFF. To reset, release the trigger.
Under extreme circumstances, the internal temperature of the battery pack could raise too much. If this happens, the fuel gauge will fl ash until the battery pack cooled down. After the lights go off , the work may continue.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations.

  • The user can transport the batteries by road without further requirements.
  • Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.

When transporting batteries:

  • Ensure that battery contact terminals are protected and insulated to prevent short circuit.
  • Ensure that battery pack is secured against movement within packaging.
  • Do not transport batteries that are cracked or leak.
  • Check with forwarding company for further advice

MAINTENANCE

Use only Milwaukee accessories and spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the machine type printed as well as the six-digit No. on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.

SYMBOLS

  • CAUTION! WARNING! DANGER!
  • Remove the battery pack before starting any work on the machine.
  • Please read the instructions carefully before starting the machine.
  • Do not dispose electric tools, batteries/rechargeable batteries together with household waste material. Electric tools and batteries that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. Check with your local authority or retailer for recycling advice and collection point.
  • No-load speed
  • Volts
  • Direct current
  • European Conformity Mark)
  • British Confomity Mark
  • Ukraine Conformity Mark
  • EurAsian Conformity Mark

Copyright 2020
Techtronic Industries GmbH
Max-Eyth-Str. 10
71364 Winnenden

Germ any
+49 (0) 7195-12-0
www.milwaukeetool.eu
Techtronic Industries (UK) Ltd
Fieldhouse Lane
Marlow Bucks SL7 1HZ
UK

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals