MONDOLUX MD35AR Albi Maxi Angular Downlight Instruction Manual

June 10, 2024
MONDOLUX

MONDOLUX MD35AR Albi Maxi Angular Downlight

Product Information

The Albi Maxi Angular DOWNLIGHT is a lighting fixture designed for ceiling installation. It has a product code of MD35AR and is available on mondolux.com.au. The product is available in three module heights: 9W (100mm), 15W (120mm), and 20W (135mm).

Warnings

  • This fitting requires 220-240V AC/50Hz power input to the driver.
  • Do not interchange any parts of this fitting.
  • It is recommended to have some space around the fitting for air ventilation to extend product’s lifetime.
  • Allow a minimum distance between fitting and illuminated subject of 800mm.
  • Do not touch fitting when in use.
  • Do not cover with any form of heat-proof material.
  • Do not install a fitting near any heat source.
  • Do not install any inductive loads such as exhaust fans etc. within the same lighting circuit of the current fitting. Issues caused by such connections will not be covered under our warranty policy.

Product Usage Instructions

  1. Ensure the mains power is turned off.
  2. Cut the required holes in the ceiling. Ensure minimum space requirements between fitting and driver. See Picture 1.
  3. Pass the driver power supply wires through the cutout and plug into the main socket.
  4. Connect the driver to the light fitting using the quick connector. See Picture 2.
  5. Mount the fitting into the ceiling and secure using spring clips. See Pictures 3 and 4.
  6. Turn on the mains power. See Picture 5.

If you have any questions about the installation of this product, please contact Mondolux.

DIMENSION

MONDOLUX-MD35AR-Albi-Maxi-Angular-Downlight-fig-1

  • Module Heights
  • 9W – 100mm
  • 15W – 120mm
  • 20W – 135mm

Warnings

  • The safety and compliance of this fitting are not assured unless the following instructions are adhered to. Please retain these instructions for future reference.
  • Always turn the mains OFF prior to installation. See the Picture below.
  • The luminaire is EN 60598-1:2015/A1:2018 compliant and Installation must be carried out by a licensed electrician.
  • Risk of Electric Shock: Prior to installation or maintenance, disconnect the fitting from the power supply and other control wiring. Faulty cables and wiring need to be replaced by manufacturer only.
  • Risk of Burns: When in use, the fitting’s surface may reach high temperatures and can cause skin burns. It is recommended to install the fitting out of reach to avoid any physical contact.
  • It is recommended to always wear safety glasses and gloves during installation.
  • For safety reasons please keep children away from the installation site.
  • Please follow the below instructions for disposal in accordance with the local E-Waste or WEEE (Waste Electrical and Electronic Equipment):
    • Fittings cannot be disposed of alongside other household waste.
    • Remove the lamp/ battery for decommissioning (if applicable)
    • Send them to the nearest E-Waste or WEEE collection center.
  • For further inquiries, please contact Mondolux at https://www.mondolux.com.au/

Notes

  • This fitting requires 220-240V AC/50Hz power input to the driver.
  • Do not interchange any parts of this fitting.
  • Its recommended to have some space around the fitting for air ventilation to extend product lifetime.
  • Allow a minimum distance between fitting and illuminated subject of 800mm.
  • Do not touch fitting when in use.
  • Do not cover with any form of heat proof material. Do not install fitting near any heat source.
  • Do not install any inductive loads such as exhaust fans etc. within the same lighting circuit of the current fitting. Issues caused by such connections will not be covered under our warranty policy.
  • If you have any questions about the installation of this product, please contact Mondolux.

Installation Steps

  1. Ensure the mains power is turned off.
  2. Cut required holes in ceiling. Ensure minimum space requirements between fitting and driver. See picture 1.
  3. Pass the driver power supply wires through the cutout and plug into mains socket.
  4. Connect the driver to the light fitting using the quick connector. See picture 2.
  5. Mount the fitting into the ceiling and secure using spring clips. See picture 3 and 4.
  6. Installation is complete. See picture 5.

MONDOLUX-MD35AR-Albi-Maxi-Angular-Downlight-fig-2

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals