VI-VID-RO-1077 VIBELL Videophone Instruction Manual
- June 10, 2024
- vibell
Table of Contents
VI-VID-RO-1077 VIBELL Videophone
Safety instructions
Before using the device, read this Service Manual and keep it for future use.
The manufacturer is not responsible for any damage that can result from
improper device installation or operation. Any repair or modification carried
out by yourselves results in loss of guarantee. Installation and commissioning
of the equipment by the customer are possible if the installer has basic
knowledge of electrical systems and the use of proper tools.
In view of the fact that the technical data are subject to continuous
modifications, the manufacturer reserves a right to make changes to the
product characteristics and to introduce different constructional solutions
without deterioration of the product parameters or functional quality.
Additional information about VI BELL products are available at
www.omo.pl. Omo-Logistic Sp. z o. o. holds no
responsibility for the results of non-compliance with the provisions of the
present Manual Omro Logistic Sp. z o.o. reserves the right to make changes to
the Manual -the latest version of the Manual can be downloaded from
support.vibell.pl Any translation/interpretation rights and copyright in
relation to this Manual are reserved.
- Do not use the device contrary to its dedication.
- Disconnect the power supply before performing any activities.
- Do not immerse the product in water or other liquids.
- Do not operate the device with damaged housing.
- Do not break the seals or open the device and do not repair it yourself.
- The product is not a toy. Keep away from children.
- Connect only as indicated in the wiring diagrams.
Damage resulting from incorrect connection is not subject to repair under warranty!
Each household is a user of electrical and electronic equipment, and hence a potential producer of hazardous waste for humans and the environment, due to the presence of hazardous substances, mixtures and components in the equipment. On the other hand, used equipment is valuable material from which we can recover raw materials such as copper, tin, glass, iron and others. The weee sign placed on the equipment, packaging or documents attached to it indicates the need for selective collection of waste electrical and electronic equipment. Products so marked, under penalty of fine, cannot be thrown into ordinary garbage along with other waste. The marking means at the same time that the equipment was placed on the market after August 13, 2005. It is the responsibility of the user to hand the used equipment to a designated collection point for proper processing. Used equipment can also be handed over to the seller, if one buys a new product in an amount not greater than the new purchased equipment of the same type. Information on the available collection system of waste electrical equipment can be found in the information desk of the store and in the municipal office or district office. Proper handling of used equipment prevents negative consequences for/he environment and human health!
CHARACTERISTICS AND USE OF THE SET
The set is used for single-family homes, offices, shops, warehouses and other access control systems.
- ultra-slim 4.3″ TFT colour display with panoramic screen;
- touch-sensitive keypad;
- infinitely adjustable monitor parameters: ring and call volume, brightness and colour;
- 16 selectable ring tones;
- 10-step adjustment of ring volume;
- control of electric door opener and gate;
- surround monitoring possible;
- vandal-proof housing of the external panel;
- surface-mounted external panel (protective canopy included).
WARNING!
Before drilling the installation holes, it is recommended to carry out a
functional test of the device. To do this, connect the device for a test
according to the wiring diagram. The first person holding the camera should
use the button to call the second person who is at the monitor. This person
should then carefully inspect the camera’s field of view in order to correct
the module’s position if necessary. Once the measurements have been taken
accurately, proceed with the mounting holes after switching off the power
supply.
SET CONSTRUCTION
Construction of the monitor VI-VID-RO-1077MV.
Construction of the external panel with camera VI-VID-RO-1077KV
WIRING DIAGRAM
WARNING
It is forbidden to make connections to live equipment! Failure to adhere to
this recommendation may result in permanent damage to the device and loss of
health.
When designing the electrical installation, take into account the appropriate cable cross-section:
-
Cable connecting the monitor to the external panel up to 15 m – recommended cable xzTKMXpw 3x2x0.5mm.
from 15 m to 50 m – recommended cable xzTKMXpw 3x2x0,8mm. -
The connection to the electromagnetic lock should be made with 1.0mm2 (up to 5m) or 1 .5mm2 ( over 5m) cable. Any electric strike with a power supply of 12VDC and power consumption of max. 500 mA.
-
The total length of the installation must not exceed 50 metres.
-
We absolutely do not recommend the use of twisted-pair cables.
Connection diagram for one monitor and two external panels
Set does not include an additional monitor and electric strike!
Video intercom cables should not be run in the same cable with cables of other
installations, e.g. ring/, alarm, telephone, etc. Any power and
telecommunication cables emitting strong magnetic fields (e.g. loudspeakers, a
TV receiver) are in direct contact with the wires connecting the door pane/to
the monitor and may adversely affect the operation of the set.
If the user has other connecting cables than those recommended, it is
permissible to use them, but a test connection of the set should be made to
check its correct operation.
INSTALLATION
Monitor installation
WARNING!
Disconnect the power supply from the monitor during installation!
- Choose a place to install the monitor.
- The optimal placement height for the monitor is 140-160 cm to suit individual needs.
- Drill two holes in the wall at the chosen height and place the mounting dowels and screws in them.
- Connect the cables according to the wiring diagram.
- Hang the unit on the screws.
- Connect the power supply to the socket.
External panel with camera installation
The correct positioning of the external panel determines the comfort of use.
Remember to avoid choosing a location that receives a lot of sunlight and is
exposed to heavy rainfall. The camera should be installed at a height of 1.4
-1.7 m.
WARNING!
Disconnect the power supply during installation I.
-
Select a suitable installation location for the camera.
-
Drill holes in the wall and insert silicone dowels. Using screws, screw in the protective canopy at a height
of 1.4m-1.7m. -
Remove the metal casing of the panel, fill in your name or house number on the plate, then replace the metal casing.
-
Connect the wires according to the diagram.
-
Mount and screw the camera to the protective canopy with the screw on the underside.
SET OPERATION
WARNING!
- Perform all operations with the power disconnected.
- Do not install the monitor near equipment that emits a strong magnetic field such as television, speakers.
- Do not install the monitor in a place exposed to high humidity.
- Do not install the monitor in a location exposed to high vibration and shock or strong sunlight.
- Do not immerse the device in water or other liquids.
- Do not operate the device if the housing is damaged.
- Do not open the unit or carry out repairs yourself.
- Do not misuse the device.
- Immediately switch off the power supply if “abnormal” sounds are emitted from the external panel or monitor.
- After installation and mounting, remove the protective foil from the monitor screen.
- Press the ring button on the external panel to make a call. The image of the visitor will automatically appear on the monitor and you will hear a ring tone. Touching the button on the monitor panel will start the call. Touching the button again will end the call. The call can last up to 120 seconds.
- Press the button, to unlock the electric strike.
- Press the button, to activate the gate control.
- Press the button on the monitor to activate the camera preview. The preview time is40 seconds. Pressing the button again will switch the view to camera 2. While monitoring, you can touch the button to engage in a conversation with a person outside. Settings for ringtone and volume, call volume, brightness and picture colour: – in monitoring or call mode, touch the button. The settings panel will appear in the upper right corner of the screen, press button again to go to “Sound settings” J’J , “Ring volume settings” “Call volume settings” , ” Display brightness settings” -;+:- , “Display colour settings” , “Exit”.
- – once the desired option has been selected, the settings can be adjusted by pressing the l!:!9E!!:l button to increase the value of the parameter concerned or to decrease its value.
- “Do not disturb” mode: touch and hold the button on the monitor, a short beep will confirm that the unit has entered “do not disturb” mode. In this mode, when the call button is pressed, the camera image will appear on the monitor, but no ringing tone will be played. The
icon will appear in the upper right-hand corner of the display. Do Not Disturb mode will be automatically switched off after 12 hours. To deactivate it faster touch and hold the button again, a double short beep will confirm the exit of the mode. The monitor has returned to normal operation.
TROUBLESHOOTING
-
No sound or vision, no indicator light on
- no power supply voltage,
- damaged or badly connected cable, check your installation for technical requirements page 4,
- check if installation is not exposed to water, moisture etc.
-
Blurred or faint image
- check settings and adjust parameters.
- Numerous distortions in the picture, lack of synchronisation (picture flashes)
the connection cable has a cross-section not suitable for its length,
-
connection too long – use a shielded cable,
- bad quality of cable,
- strong source of electromagnetic interference – use shielded cable.
-
Monitors sound interrupts or jams
- check your installation against the technical requirements.
- check that the installation is not exposed to water, moisture etc.
-
Electric strike does not open every time
- check the independent functioning of the electric strike by connecting it to the required voltage, etc.
-
New scratched monitor
- check that the protective foil is removed from the screen.
TECHNICAL DATA
- TYPE OF DEVICE : single family
- INSTALLATION METHOD : 4-wire
- COMMUNICATION SYSTEM : wired
MONITOR
- SCREEN SIZE : 4,3″
- RESOLUTION : 480(RGB)x272
- STANDARD : PAL
- STANDARD : call, monitoring, door and gate control, monitor and volume control, “do not disturb” mode
- NUMBER OF MELODIES : 16
- VOLUME : call <B0dB, ring <70dB
- CALL TIME : 120s±10%
- MONITORING TIME : 40s±10%
- GATE CONTROL : yes, potential-free contact
- POWER SUPPLY : 12V DC, 1,5A
- POWER CONSUMPTION : standby <1W; work <12W
- WORKING TEMPERATURE : -1o·c- +4o•c
- INSTALLATION : surface-mounted
- MATERIAL : ABS
- DIMENSIONS : 133x103x19mm
- NET WEIGHT : 0,182kg
EXTERNAL PANEL
- SENSOR TYPE : CMOS
- RESOLUTION : 700TVL
- VIEWING ANGLE (VERTICAUHORIZONTAL) NIGHT LIGHTING : 48°/ 68°
- NUMBER OF DIODES : IR
- NIGHT VISION RANGE : 4
- ELECTRICAL STRIKE CONTROL : 1m
- DEGREE OF PROTECTION : 12V DC, max. 500mA
- POWER SUPPLY : IP44
- WORKING TEMPERATURE : from monitor (12V DC)
- INSTALLATION : -10″C – +40″C
- MATERIAL : surface-mounted
- DIMENSIONS : metal. ABS
- NET : 65x143x41mm
- WEIGHT : 0,244kg
ORNO-LOGISTIC Sp. z o.o.
ul. Rolnik6w 437
44-141 Gliwice, Poland
NIP:6351831853
REGON: 243244254
tel. +48 32 43 43 110, www.orno.pl
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>