STETSOM HL1000.2 HIGH LINE Automotive Amplifier User Manual

HL1000.2 HIGH LINE Automotive Amplifier

Product Information: High Line Automotive Amplifier

The High Line Automotive Amplifier is a powerful amplifier designed to provide high-quality sound for your car’s audio system. The model number is HL1000.2, and it has a total power output of 900 RMS with a minimum impedance of 2 Ohms. It has 4 channel that can be connected in BRIDGE with a minimum impedance of 4 Ohms. The amplifier operates in frequencies from 10Hz to 22KHz.

Features :

• 4 channels
• 900 RMS of total power
• Minimum impedance of 2 Ohms
• Can be connected in BRIDGE with a minimum impedance of 4 Ohms Operates in frequencies from 10Hz to 22KHz Before Installing:

Please read the user manual carefully before installing the amplifier. All product connections must be made with the product turned OFF. A fuse must be installed between the amplifier and the battery. If you have any questions, contact the store where the purchase or installation was made. For more information, please contact our Customer Service: BR +55 18 2104-9412.

Installation :

For proper installation, use the recommendations according to the model purchased. Check the minimum impedance supported by the amplifier. The following specification of cables is required for proper installation:

• Power connectors (positive/negative): 6 AWG
• Remote connector: 18 AWG
• Output signal connectors (speakers): 13 AWG
• Fuses or circuit breakers: 40A

The use of fuse or circuit breaker is mandatory to protect the system from short circuit and overload. Install them as close to the battery as possible.

Product Usage Instructions:

1. INPUT (Front e Rear): This input should receive the signal through an RCA cable that is properly connected to the RCA output of the Radio/MP3 Player. Entries are divided into REAR (rear channels) and FRONT (front channels). We recommend RCA cables with STETSOM triple shielding.

2. Observe the LEDs on the top cover of the amplifier to view its operation: POWER (blue LED) indicates the operation of the amplifier when lit. PROT (red LED) will light up in the following situations: Short circuit at the speaker outputs, temperature above that allowed.

3. Adjust the cutoff frequency of the Crossover with the FREQUENCY control. The adjusted frequency acts on both H.P.F and L.P.F., depending on which is selected.

4. For proper installation, use 13 AWG cables according to the model purchased. Check the minimum impedance supported by the amplifier.

5. When installing speakers, use the following installation examples:

• 2 OHM AMPLIFIER (2 x 2 ohm speakers) – STEREO
• 2 OHM AMPLIFIER (1 x 4 ohms woofers) – BRIDGE

6. Use a REMOTE cable with 18 AWG and a recommended auxiliary battery for optimal performance.

7. To ensure proper ventilation, avoid obstruction of air inlets and outlets.

Features

The HL1000.2 has 4 channels which provide 900 RMS of total power with a minimum impedance of 2 Ohms. It can be connected in BRIDGE with a minimum impedance of 4 Ohms and operates in frequencies from 10Hz to 22KHz.
It has Left (L) and Right (R) channels with controls:

• Level: Adjusts the level of the input signal;
• Crossover: Allows you to choose between Low-Pass, High-Pass or Flat (Full-Range) performances;
• Bassboost: Allows variable tuning of the attenuation of the low frequency ranges from 0dB to + 20dB

Before installing

Please read this manual carefully.

• All product connections must be made with the product turned OFF.
• A fuse must be installed between the amplifier and the battery is required to protect against overcharging. The fuse has to be installed as close to the battery as possible. Check the proper fuse for the amplifier according to its consumption.
• Use gauges recommended in this manual to avoid the overheating of the cables to obtain maximum power.
• Keep the cables as short as possible to increase sound fidelity and avoid potential power losses.
• Route the installation cables as far away as possible from the original vehicle wiring as it may cause interference and noise in your audio system.
• Perform the installation in a firm, ventilated and dry place.
• Installation must be done by a qualified professional.

If you have questions , contact the store where the purchase or installation was made. For more information please contact our Customer Service: BR +55 18 2104-9412.

Input and audio controls

1.  INPUT (Front e Rear): This input should receive the signal through an RCA cable that is properly connected to the RCA output of the Radio/MP3 Player. Entries are divided into REAR (rear channels) and FRONT (front channels). We recommend RCA cables with STETSOM triple shielding.

2.  LEVEL (Volume control): Responsible for controlling the level of the input signal. The left regulator controls the REAR input and the right regulator controls the FRONT. They provide proper adjustment for any Radio/MP3 Player.

3.  BASS BOOST: Reinforces the bass level at low frequencies 25Hz to 110 Hz. From 0 to + 20dB centered on 45Hz.

4. CROSSOVER (SLIDE SWITCH L.P.F./ FLAT / H.P.F): This switch allows you to select that type of CROSSOVER will be used for the channels, with the left regulator for the REAR input and the right for the FRONT input.
   The switch has three positions:
   L.P.F: In this position, the LOW-PASS filter that reproduces low frequencies (below 90Hz) will be activated;
   FLAT: In this position, the channel will be operating in FULL-RANGE and all the frequencies present in the audio will be reproduced;
   H.P.F: In this position, the HIGH-PASS filter that reproduces the high frequencies (above 90Hz) will be activated.

5. COOLER: It provides cooling of the amplifier. Install in a cool place without obstruction of air inlets and outlets.

6. FREQUENCY: Adjusts the cutoff frequency of the Crossover. The adjusted frequency acts on both H.P.F and L.P.F., depending on which is selected.

Tips for adjusting the input signal:

• On the Radio/MP3 Player, turn on any musical signal and set the volume to 80% of the maximum. For example: if the maximum volume of the Radio/MP3 player is 45 (100%), set to 36 (80%).
• On the amplifier, put the LEVEL at the lowest setting and increase gradually until you notice the sound distorting.
• Slowly lower the LEVEL until you no longer hear distortion in the sound.

Audio output and power **

**

5. OUTPUT CONNECTOR (SPEAKERS): FRONT and REAR outputs with stereo signal. Be careful to maintain the correct polarity of the speaker connections and check the minimum output impedance in the technical specifications.
6. REMOTE CONNECTOR (REM): Allows automatic activation of the amplifier when turning on the radio/player. Connect to the remote output of the radio/player mininum of 18 AWG.
7. NEGATIVE POWER SUPPLY CONNECTOR: Connect to the negative battery terminal using cables with a gauge recommended for the model purchased.
8. POSITIVE POWER SUPPLY CONNECTOR: Connect to the positive battery terminal using cables with a gauge recommended for the purchased model. Always use a fuse compatible with the consumption of the product closest to the battery to protect the electrical part of the vehicle.

Indicators LEDs
The product has two LEDs on the top cover that allow you to view its operation:
POWER (blue LED ): Indicates the operation of the amplifier when lit.
PROT (red LED): The led will light up in the following situations:

• Short circuit at the speaker outputs.
• Temperature above that allowed.

Instalation

Specification of the cables for proper installation:

• Power connectors (positive/negative) …………………………………. 6 AWG
• Remote connector ……………………………………………………………. 18 AWG
• Output signal connectors (speakers) …………………………………… 13 AWG
• Fuses or circuit breakers …………………………………………………….. 40A

The use of fuse or circuit breaker is mandatory to protect the system from short circuit and overload. Install them as close to the battery as possible.

Installing speakers
For proper installation, use the recommendations according to the model purchased:
Check the minimum impedance supported by the amplifier.

SPEAKERS: 13 AWG cables

STEREO

INSTALLATION EXAMPLES: 2 OHM AMPLIFIER (2 x 2 ohm speakers)

BRIDGE

INSTALLATION EXAMPLES : 2 OHM AMPLIFIER (1 x 4 ohms woofers)

Technical specifications

Any updates made in this manual will be available for consumers to consult without any charge on the brand’s site.
It is recommended that the updated manual be consulted whenever necessary.
The data measured are based on STETSOM laboratory equipment. Test reference in frequency from 1Khz with THD + N at ≤10% in impedances as indicated in each measurement. The electronic components and the manufacturing process may present manufacturing variations, thus leading to a variation in the measurements made.

Troubleshooting

DOES NOT TURN ON:

• Check that the cables are connected correctly. Make sure that all connections have electrical and mechanical contact.

• The fuses or circuit breakers may be faulty or blown. Check the status of the circuit breakers and make sure they are compatible with the consumption of the equipment.

• Check the charge of the battery and make sure it is sufficient to operate the product.
  NO SOUND:

• Speaker cables or RCA plugs may be defective or not connected correctly.

• Make sure that the LEVEL control is not set to minimum.
  LED PROT ON:

• Check to see if the ventilation inlet of the product is obstructed or the product is overheated.

• Check the loud speakers, cables and connections for short circuits. POOR SOUND QUALITY (DISTORTIONS):

• The speakers may be overloaded or defective, lower the level and redo the level adjustment.
  WEAK BASS:
  The polarity + and – of the speaker cables can be inverted (speaker  out of phase).
  NOISE AND SOUND FAILURES:
  

• Run the shielded input cable away from all other cables since it is more sensitive to interference.

• Install a separate power source (+ 12V) for the sound system. Use a fuse/breaker within 30 cm of the battery for protection.

• Ground the amplifier well. To do this, remove the paint from the vehicle chassis at the desired point and connect the wire using a grounded terminal. In order to prevent rust, insulate it with paint.

• Do not loop the ground or use multiple grounds. If possible, use a star connection in which all the grounds run from a single point.

Warranty information

STETSOM, through its network of Authorized Technical Assistance Providers, guarantees technical assistance to the purchaser of their products. The repairs of any defects duly established as being of the manufacturer will be done without cost for replacement components or parts and repair labor. The repairs will be done by the Authorized Technical Assistance Provider specially designated by STETSOM.
CONSULT THE LIST OF AUTHORIZED TECHNICAL ASSISTANCE PROVIDERS ON OUR WEBSITE: : www.stetsom.com.br/en/assistencias-tecnica
If you do not locate technical assistance in your city, please contact us at: BR +55 18 2104-9412

WARRANTY TERM CONDITIONS:
Our warranty is 1 (one) year against manufacturing defects. Its validity starts on the date of the Sale to the FINAL Consumer.
To make use of the benefits of this warranty, you must present one of the following documents: the Final Consumer’s SALE NOTE or this completed CERTIFICATE.

CASES THAT VOID THE WARRANTY:

1. 1 year after the issuance of the invoice of sale to the consumer or 1 year of completing certificate of warranty (dated and stamped by the retailer or installer) or 1 year from date of manufacture.
2. Violation of seals, alteration or removal of the product’s serial or lot number.
3. If the product suffers misuse, careless accidents involving: Water, Fire or Fall, or is installed in conditions contrary to the guidelines contained in the installation manual that accompanies the product.
4. Damages and changes in the circuit or adaptation of non-original parts.
5. If you use installation techniques contrary to those given in the manual.

QUESTIONS AND ADVICE:
STETSOM offers Customer Services to answer questions and give advice about their products and services. Please contact us through the channels: Phone: BR +55 18 2104-9412 — E-mail: suporte@stetsom.com.br
Site: www.stetsom.com
Images contained in this manual are merely illustrative and may differ from the actual product.

References

• Stetsom - Stetsom
• Stetsom - Stetsom
• Assistências TécnicaTechnical AssistanceAsistencias Técnica - Stetsom
• Assistências TécnicaTechnical AssistanceAsistencias Técnica - Stetsom
• Assistências TécnicaTechnical AssistanceAsistencias Técnica - Stetsom

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>