Carmanah Speedcheck-12 Radar Speed User Manual

June 10, 2024
carmanah

Carmanah Speedcheck-12 Radar Speed User Manual
Carmanah Speedcheck-12 Radar Speed

Warnings and Precautions

The following symbols indicate important safety warnings and precautions throughout this guide:

Safety Icon| WARNING indicates that serious bodily harm or death may result from failure to adhere to the precautions.
---|---
| CAUTION indicates that damage to equipment may result if the instructions are not followed.
| NOTE suggests optimal conditions and provides additional information.

Warranty Disclaimer

This manual will familiarize you with the features, operation standards and installation of Carmanah’s SPEEDCHECK-12 solar charge controller.
Failure to comply with the use, storage, maintenance, installation or placement instructions detailed in this manual could void the warranty.

Standards

Perform all installation, wiring, grounding and maintenance in conformance with local building and electrical codes.
Adherence to the National Electrical Code (NEC) is mandatory to comply with any certification markings.
Non-adherence to code may void the warranty.

Safety and Usage Precautions

Safety Icon| Batteries are shipped fully charged. Use extreme caution when handling the batteries as they can generate hazardous short-circuit currents. Remove all jewelry (bracelets, metal-strap watches, etc.) before entering the cabinet.
---|---
Safety Icon| Solar panels produce DC electricity when exposed to light and can therefore produce an electrical shock or burn. To render solar panels inoperative, remove them from sunlight or fully cover their front surface with an opaque material.
Safety Icon| Before lifting any heavy or bulky equipment, ensure the load is secured so moving parts do not shift, and that it can be lifted as far as needed without back strain or loss of grip. Installation may require more than one person.
Safety Icon| Ensure the equipment is not powered during installation and wiring of the system.
Safety Icon| Recheck all completed wiring for proper polarity prior to energizing the system.
| Changes or modifications to Carmanah equipment not expressly approved by Carmanah could void both the user’s authority to operate the equipment and the warranty
Safety Icon| Product can have sharp edges. Accidental movement of hinged components can cause injury.
| This guide is specific to the SPEEDCHECK-12 replacement solar charge controller installation and is not a replacement for the complete SPEEDCHECK-12 product user manual.
Visit support.carmanah.com to download the complete product user manual.

System Components

The SPEEDCHECK-12 replacement solar charge controller consists of the following items:

  1. Solar charge controller, SPEEDCHECK-12 (1)
  2. Rivet, 3/16”, aluminum (2)

Tools and Materials Required

The following tools and materials may be required to install the solar charge controller into your SPEEDCHECK12 system:

  1. Drill and drill bit set
  2. Socket set
  3. Crescent wrench
  4. Multi-bit screwdriver
  5. Rivet installation tool with nosepiece for 3/16” diameter rivet

Installation

Opening Rear Enclosure

  1. To open SPEEDCHECK-12, insert included key into lock and rotate clockwise.

  2. Apply diagonal pressure to the bottom right corner of the sign face then PULL on the key.

  3. Once unlocked, the key can be removed.
    Installation Instruction

  4. Swing the display enclosure away from the rear enclosure.

  5. Disconnect all 2-pin connections at the display enclosure bracket.

  6. Temporarily lock the SPEEDCHECK-12 by pushing the display enclosure against the rear enclosure then PUSH the lock to secure in place.
    This will secure the system while working on the solar kit.
    Installation Instruction

Removing Solar Panel

| These instructions will cover leaving the solar kit attached to the pole while removing and replacing the solar charge controller.
If required, you may also remove the entire solar kit from the pole to work on the ground instead.
For more information on how the solar kits are installed, see the SPEEDCHECK-12 manual at support.carmanah.com.
---|---

  1. Locate the top four mounting bolts for the solar panel and remove the top two while leaving the bottom two loose.
  2. Disconnect solar panel power harness.
  3. Remove the bottom two bolts and set hardware aside and solar panel aside.
    Removing The Solar Panel

Removing Solar Charge Controller

  1. Remove the plastic cover plate on the front of the charge controller.

  2. Remove the wiring on the Solar and Battery terminals connected to the charge controller.
    Take note of where the wiring was originally terminated.

  3. Disconnect the power harness that goes down to the pole to the SPEEDCHECK-12 display.

  4. Drill out the two rivets securing the charger controller and remove the controller from the system.
    Remove all metal chips from the solar housing.
    Removing Solar Charge

Installing Solar Charge Controller

  1. Fit the new charge controller in the same location and orientation as previously installed.
    Installing Solar Charge Controller

  2. Insert the two provided rivets from the rear of the solar housing and rivet the charge controller to the housing.
    Installing Solar Charge Controller

  3. Reconnect the charge controller wiring from Section 4.3.

  4. Reinstall the plastic cover plate and secure with the two previously used screws.
    Installing Solar Charge Controller

  5. Reconnect the power harness that goes down the pole to the SPEEDCHECK-12 display.

| For systems with Street Hub, you will have an extra yellow wire terminated to Solar+.
---|---

Reinstalling Solar Panel

  1. Lower solar panel on housing and loosely install 2x bolts at mounted end of housing, noting location of power harness.
  2. Lift other end of solar panel up and connect power harness, ensuring connector is fully engaged.
  3. Lower solar panel, taking care not to pinch solar panel harness, and install remaining bolts. Tighten all 4 bolts.
    Reinstalling Solar Panel

System Reassembly

  1. Reconnect all 2-pin connectors at the display enclosure bracket.
    System Reassembly

  2. To close, push the display enclosure against the rear enclosure and then apply diagonal pressure in the bottom right corner of the sign face.
    Once fully closed then PUSH the lock to secure in place.
    System Reassembly

CUSTOMER SUPPORT

Email: customersupport@carmanah.com
Toll Free: 1.877.722.8877 (US & Canada)
Worldwide: 1.250.380.0052
Fax: 1.250.380.0062
Web: carmanah.com
Logo.png

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals