Claber 8419 Aquauno Logica Plus Water Timer User Manual
- June 10, 2024
- claber
Table of Contents
Claber 8419 Aquauno Logica Plus Water Timer
Product Information
- Product Name: Aquauno Logica, Aquauno Logica Balcony, Aquauno Logica Plus, Eco-Logic
- Product Type: Water Timer
- Usage: Used for irrigation purposes by connecting it to a tap and a system
- Installation: Do not install the timer inside valve boxes, below ground level or indoors. Do not use the timer with chemicals or liquids other than water. Do not use the timer with operating pressures lower than 0.5 bar (7.3 psi) or higher than 10 bar (145 psi).
- Battery: Requires a new, branded 9V alkaline battery
Product Usage Instructions
- Installation: Connect the timer to a tap and connect it to the system. Do not install the timer inside valve boxes, below ground level or indoors. Do not use the timer with chemicals or liquids other than water. Do not use the timer with operating pressures lower than 0.5 bar (7.3 psi) or higher than 10 bar (145 psi).
- Battery Fitting: Press the two side buttons to open the timer and insert a new, branded 9V alkaline battery. Remember to turn on the water tap.
- Programming the Timer: The pre-set irrigation run time and frequency of each program cannot be changed. The characteristics of all programs are summarised in a list provided on the protective cover.
INSTALLATION
Connect the timer to a tap and connect it to the system. Do not install the water timer inside valve boxes, below ground level or indoors. Do not use the water timer with chemicals or liquids other than water. Do not use the water timer with operating pressures lower than 0.5 bar (7.3 psi) or higher than 10 bar (145 psi).
FITTING THE BATTERY
Press the two side buttons to open the timer and insert a new, branded 9V
alkaline battery. Important: remember to turn on the water tap.
USE
Programming the timer. All of the programme characteristics are summarised in
a list provided on the protective cover. Each programme has a pre-set
irrigation run time (i.e. how long to irrigate for) and frequency (i.e. how
often to irrigate). Neither of these settings can be changed.
- For timers (code)
USE
Programming the timer. At the time you want irrigation to start, turn the dial
to the desired programme. The selected programme starts after 10 seconds. With
Aquauno Logica Plus (code 8419), a green LED lights up during operation. When
the batteries are running low, the LED is red.
USE
Changing a watering programme. The irrigation programme can be changed at any
time by turning the dial to OFF/0 and then turning it to the new program you
want to use at the time you want the irrigation cycle to start.
RAIN SENSOR.
With Aquauno Logica Plus (code 8419), you can connect the Rain Sensor (code
90915) to the timer by replacing the existing bridge connector installed with
a specific connector. If it starts to rain, the Rain Sensor will not stop the
irrigation cycle in progress but it will stop the subsequent cycles if the
level of water inside it reaches a sufficient level (at least 5 mm of
rainfall). If you are not using the Rain Sensor, leave the bridge connector
inserted.
CLEANING AND MAINTENANCE. Clean the filter at the end of each season and check it regularly. Turn off the water tap and loosen the screw collar, turning anticlockwise. Loosen the 3/4″ screw collar of the tap connector, turning clockwise. Remove the filter. Rinse the filter clean under running water. After washing, reassemble all parts as before. To clean the internal components properly, please see the diagram showing the mechanical parts to be disassembled/ reassembled at the end of the season.
CLEANING AND MAINTENANCE. At the end of the season, before the winter frosts, disconnect the timer from the tap, remove the battery and store the timer in a sheltered place, away from damp, where the temperature does not fall below 3°C.
For timers (code):
8419 – 8422 – 8444 – 8446 – 8932
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>