Atlanta ATH-6786 Electric Hair Dryer Instruction Manual
- June 10, 2024
- ATLANTA
Table of Contents
Atlanta ATH-6786 Electric Hair Dryer
Product Information
Product Name: ATH-6786 Electric Hair Dryer
Brand: ATLANTATM
Ver: 2.06.2010
Technical Specifications:
- Voltage: 230 V~ 50 Hz
- Rated power: 2000 W
- Noise level: less than 68 dB
- Service life: 3 years
Features:
- Non-airheat drying
- Gentle airflow for soft drying or styling
- High airflow for ultra-fast drying or styling
Product Usage Instructions
- Before operating, read the safety measures in the instruction manual.
- Identify the parts of the hair dryer using the diagram in the instruction manual.
- Plug the hair dryer into a power source with the voltage mentioned in the technical specifications.
- Use the switch (D) to turn on the hair dryer.
- Select the desired airflow setting using the switch (F).
- Start drying your hair from the back, taking one strand at a time. Move the airflow from roots to ends of hair.
- Proceed to styling until the hair is still wet. You should completely finish one strand before you take the next.
- After usage, clean your hair dryer as per the instructions given in the manual.
- Do not dispose of old appliances with household waste. Hand it over to a receiving utilization office.
If you have any questions or concerns, please contact ATLANTA using the contact information provided in the manual.
INSTRUCTION MANUAL
DEAR CUSTOMER!
CONGRATULATIONS ON YOUR GOOD CHOICE! NOW YOU ARE THE OWNER OF ATLANTATM
PRODUCT NOTABLE FOR ITS PROGRESSIVE DESIGN AND GOOD QUALITY PERFORMANCE. WE
HOPE OUR PRODUCTS WILL STAY WITH YOU FOR YEARS ON END.
BEFORE OPERATING
Please, read all these instructions carefully before using the appliance. We recommend you to adheres to the distance from the nozzle to the hair at least 15cm. Compliance with this requirement ensures the temperature effect on the hair at 57 ° C which is perfect temperature for normal type of hairs. If you use a hair dryer for styling you can use your short exposure to a small strand of hair with reduced distances of up to 5 cm. The temperature effect in this case will be at 70 °C
SAFETY MEASURES
- The device is designed to operate on two types of voltages. Please be sure the voltage switch (E) have been set to the position corresponding the supply voltage you are going to connect. Otherwise, hair dryer burn, and this item will be out of warranty.
- Do not allow water or any other liquid to go into the unit, as it can damage the appliance.
- After transportation in lower temperature conditions leave the appliance in a warm room for at least two hours before switching it on.
- The hair curling tongs is adjusted to function with the power supply specified in the instruction.
- Do not operate the appliance near objects that can be easily deformed by high temperature.
- Do not use this appliance near bathtubs, showers, basins or other vessels containing water.
- THE DEVICE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING CHILDREN) WITH REDUCED PHYSICAL, SENSORY OR MENTAL ABILITY OR IF THEY HAVE NO EXPERIENCE OR KNOWLEDGE, IF THEY ARE NOT UNDER CONTROL OR NOT INSTRUCTED ON THE USE OF THE INSTRUMENT THE PERSON RESPONSIBLE FOR THEIR SAFETY.
- DO NOT LEAVE THE APPLIANCE UNATTENDED WHEN THEY IS PLUGGED IN OR WHEN CHILDREN ARE AROUND. A POWER SUPPLY CORD MUST NOT BE HUNG DOWN AS CHILDREN CAN PULL IT, THROW THE APPLIANCE AND GET BURNT.
- If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
- Close supervision is necessary when the appliance is used near children. Never leave the appliance unattended when in use. Do not allow children to use the appliance unsupervised.
- Do not put the hair curling tongs on soft, uneven or thermo unstable surface when in use.
- Do not use any attachments or accessories not recommended or sold by this appliance manufacturer.
- Do not touch the styling plates with finger tips; the operating temperature goes up to 180° С.
- Do not twist the cord or wind it round the appliance.
- Disconnect the appliance from the power supply after use.
- In order to reduce the risk of fire and electric shock:
- do not scrape the body of the kettle;
- do not expose the electric part of the kettle to rain or water exposure;
- do not submerge the appliance into water or other liquid;
- KEEP THE APPLIANCE PLUGGED OUT IF IT IS NOT USED, THE DEVICE IS DANGEROUS EVEN IF IT IS UNPLUGGED;
- do not cover the hair curling tongs with anything;
- do not use this appliance in damp rooms;
- do not hold the appliance with wet hands;
- do not plug or unplug the appliance if your hands are wet;
- do not allow the plug to overheat; make sure the appliance is properly plugged;
- do not use the hair curling tongs if the supply cord is damaged or wet;
- switch off and remove the plug from the power outlet before cleaning;
- never pull the power supply cord to disconnect the plug from the socket; instead, grasp the plug and pull to disconnect;
- store the appliance in a cool dry place.
- This product is intended for personal use only.
- If the appliance is damaged during use, disconnect it from the power supply immediately. Do not attempt to repair the appliance yourself; instead, take it to your nearest Authorized Service Centre for repair and show your warranty ticket.
- After transportation under low temperature conditions, the device can be connected to the mains only after two hours in a warm room.
- Do not use any chemically active liquids (petrol, kerosene, alcohol, various solvents) for cleaning the housing of the device.
- Any faults in storage, transportation or operation of the device are not covered by the warranty.
HAIR DRYER PARTS IDENTIFICATION
- A – concentrator nozzle
- B – housing
- C – air inlet
- D – back cover
- E – «COOL» function button
- F – on/off /speed control
- G – power control
- H – handle
- I – power cord
TECHNICAL SPECIFICATIONS
- Voltage: 230 V~ 50 Hz
- Rated power: 2000 W
- Noise level: less 68 dB
- Service life: 3 years
The date of manufacture is provided in the serial number of the products: the third and the fourth digits – month of manufacture, the fifth and the sixth digits – year of manufacture. Example: хх0219хххххх – month 02, year 2019.
STYLING
- Completely unwind the electric cord.
- Connect the selected attachment to the hair dryer body. The use of the attachment is optional; you may perform the simple drying without attachment. Please use towel to dry your hair well and use comb before you turn the hair dryer on.
- Plug the hair dryer into a suitable power supply after making sure that the speed switch (F) is in the “0” (off) position.
- Use the switch (F) to set motor speed into position « » or « ».
- Set the power switch (G) to the appropriate position:
- minimum power (non-airheat drying);
- gentle airflow for soft drying or styling;
- high airflow for ultra fast drying or styling.
- Start drying hair from the back taking a strand for a strand. Move the airflow from roots to ends of hair.
- Proceed to styling until the hair is still wet. You should completely finish of one strand before you take next.
- You can also sue the cool air function by pressing the «COOL» button (E). The essence of this function is the combined use of high temperature and cool shot to get shape fixed well.
- If you hear any strange noises while using the appliance or the operation of the hair dryer motor is disturbed, it may be the sign of the hairs stuck in the air inlet.
- After use set the speed switch (F) into the “0” position and unplug the appliance.
Before storing the hair dryer let it cool down.
NOTES
- When first in use or after a long rest period, you may notice a characteristic odor of burnt dust accumulated on the heating element.
- This appliance is equipped with an automatic thermal limiter. If the appliance overheats or the air intake vents are blocked or clogged, an automatic device will switch the dryer off.
- After the heating element is cooled down and the temperature is back to normal you can restart the appliance and use it as usual.
- The manufacturer has the right to make alterations in the hair dryer design.
HOW TO CLEAN YOUR HAIR DRYER
- Use a soft dry cloth to wipe the outside surface.
- Unplug the unit and let it cool down, then use a soft damp cloth to wipe the outside surface. Do not clean the hair dryer with chemically active liquids or abrasive washing agents, as they can damage the surface.
- Do not clean the hair dryer with the help of other tools.
- Do not immerse the appliance in water or other liquids.
ENVIRONMENTAL INSTRUCTIONS
Old appliances are a set of technical materials, so they may not be utilized together with household waste! That is why we kindly ask you to give us an active support in saving the resources and protecting our environment and to hand it over to a receiving utilization office (if any).
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>