LUXLOGIC LIGHTING Rainbow Series LED Ceiling Light Instruction Manual
- June 10, 2024
- LUXLOGIC LIGHTING
Table of Contents
RAINBOW SERIES (SURFACE MOUNTED)
LED Ceiling Light
Instruction Manual
Rainbow Series LED Ceiling Light
Please read this installation manual carefully before installation. Keep it for future reference! Products are well packed and tested before leaving our factory. Please strictly follow the instructions listed in the manual. Factory cannot be held responsible for any mis-operation or damage caused by not following the installation manual!
Installation Diagram
Step 1
Shut “OFF” the electricity at electrical panel.
Place the wall switch in the “OFF” position ofthe room you are installing the
fixture.
Step2
Use Screw driver to relieve Canopy screwalittle.(Do NOT REMOVE). Rotate
Mounting Bracket and Remove it from Bottom Bracket as shown below.
Step3
Remove Plastic Pin ,drill 4 pcs or 6 pcs diameter 6mm holes on the ceiling
according to Mounting Bracket. (note: If the fixture dia is larger than 2” , 6
holes are required, 4 for Bracket screw, 2 for safety Bracket screw). Please
note: safety cable suspension is only applicable for diameters of 3ft and
above. For diameters of 2ft and below, no safety cable suspension is required.
Insertthe expansion bolts into the holes.( Use 2 pcs M4*25mm Screws to attach
Mounting Bracketto the J-Box. Refer to picture shown below.
NOTE: J-BOX Garvin 54171-S or equivalent / Provided by others
Step4
Use 4pcs or6pcs (2 for Safe Bracket) M4*25 Self-Tapping screw to attach
Mounting Bracket on the ceiling.
And Connect the safety cable between Mounting Bracket and Canopy.
Attention: Must secure mounting plate at all connection points (junction
box plus four outer points for small and medium sizes, or six outer points for
larger size) to support fixture weight appropriately. Not using all mounting
points could damage the fixture and void product warranty.
Step 5
Use wire connectors to connect L,N,G,DIM+,DIM- wires. Then place all wires
with connectors into J-Box
Step 6
Keep the Slot hole in a vertical line with Side screw. Then, screw into slot.
Next, rotate lamp body To complete installation.
Step 7
After installation is complete, turn on the electricity at the electrical
panel.
Warnings
-
MIN 90 °C SUPPLY CONDUCTORS/LES FILS D’ALIMENTATION 90 °C MIN
-
DAMP LOCATIONS ONLY/POUR EMPLACEMENTS SECS SEULEMENT
-
CAUTION – RISK OF FIRE/ATTENTION – RISQUE D’INCENDIE
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BYAPERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED/CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS -
Application temperature for ring light is -20 ° ~40 ° ， humidity is 0~95 ％ . Otherwise there may be harm to the lifespan of the ring light.
-
Please TURN OFF POWER before installation. This lamp must be installed and maintained by electrician or qualified personnel.
-
Pay attention to fire prevention, electricity and shock resistance.
-
Please do not cover the combustibles on the fixture.
-
All screws and terminals should be tightened and tightly inserted. No loosening and improper connection are allowed.
Attention should be paid to the polarity of components, power supply, driver and so on. -
Terminals should be tightened and tightly inserted. No loosening and improper
RAINBOW 16″
BRACKET DIMENSIONS
11.8” (300mm) / 15.7” (400mm)
RAINBOW 24″
BRACKET DIMENSIONS
RAINBOW 36″
BRACKET DIMENSIONS
RAINBOW 48″
BRACKET DIMENSIONS
luxlogiclighting.com
info@luxlogic.ca
tel.416-833-5515 toll free.
1-888-553-8003
Rev 1.0 27.11.2022
Documents / Resources
|
LUXLOGIC LIGHTING Rainbow Series LED Ceiling
Light
[pdf] Instruction Manual
Rainbow Series LED Ceiling Light, Rainbow Series, LED Ceiling Light, Ceiling
Light, Light
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>