EcoBurner Sustainable Buffets User Manual
- June 10, 2024
- EcoBurner
Table of Contents
EcoBurner Sustainable Buffets
Product Information
The EcoBurner is a fuel-powered burner that delivers heat for various
purposes. It is designed to be used indoors and outdoors. The burner is easy
to fill and use, and it comes with a short online training video accessible at
www.ecoburner.com/support or via the QR code provided in the manual. The
EcoBurner should be
stored in a 4×4 dishwasher rack and left to cool down for 15 minutes after
use. It is essential to follow the filling instructions correctly and never
overfill the EcoBurner. The maximum weight of a filled EcoBurner should be
435g (15.5 oz).
Product Usage Instructions
Before using the EcoBurner, make sure to watch the short online training video available at www.ecoburner.com/support or via the QR code provided in the manual. Follow these steps for using the EcoBurner:
Storage
After use, leave the EcoBurner to cool down for 15 minutes. Store the EcoBurner in a 4×4 dishwasher rack, placing it correctly. For best practice, store full Eco Burners upside down in the rack, and Eco Burners that require refilling should be stored upright.
Filling
Follow these steps for filling the EcoBurner:
- Refill in a well-ventilated area away from where fuel may gather (e.g. sinks/basins). Fuel vapor is heavier than air and may gather in confined places.
- Check if more fuel is required by placing the EcoBurner on the filling station. Do not refill an EcoBurner that is already full (at the top of the green area).
- Place the EcoBurner on a flat surface, and rotate the fuel can until the green tip drops into place. Press down firmly to commence filling.
- After filling, confirm the fill level using the filling station to ensure the fill level is at the top of the green zone. Allow the burner to return to room temperature before use.
Using the EcoBurner
Follow these steps for using the EcoBurner:
- Rotate the handle fully anti-clockwise to MAX position, and you should hear the gas start to flow.
- Place the EcoBurner on a flat surface and light the EcoBurner using a lighter or matches.
- Allow 60 seconds for the head to turn orange before moving the burner into place.
Troubleshooting
If there is no gas flowing, follow these steps:
- Check the fill level using the filling station.
- Check if the OTV has been activated and reset if necessary.
- If the EcoBurner is overfilled, allow excess fuel to vent off in a well-ventilated area. An overfilled EcoBurner may flare (flame from head). This flaring will cease when the excess fuel is burnt off/removed.
Note: Never overfill the EcoBurner and always use the filling station. The maximum weight of a filled EcoBurner should be 435g (15.5 oz).
STANDARD OPERATING PROCEDURES
All users of the EcoBurner system should watch the short online training video prior to using or filling the EcoBurner. The video is accessible at either www.ecoburner.com/support or via the QR code above.
STORAGE
- EcoBurners should be left for 15 minutes to cool down after use.
- After filling, store EcoBurners in a 4×4 dishwasher rack as shown.
- EcoBurners that require filling should be placed into the rack the correct way up.
BEST PRACTICE
Full Eco Burners ready for use, should be stored upside down in the rack. Using an upside down burner means it will deliver max run time. Eco Burners that require refilling, after service, should be stored upright.
FILLING
- Only refill Eco Burners in a well ventilated area and away from where fuel may gather (e.g. sinks /basins) Fuel vapour is heavier than air and may gather in confined places.
- Prior to filling, check if more fuel is required by placing on the filling station. DO NOT refill an EcoBurner that is already full (at the top of the green area).
- Place the EcoBurner on a flat surface, rotate the fuel can until the green tip drops into place. Press down firmly to commence filling.
- After filling, confirm the fill level using the filling station to ensure the fill level is at the top of the green zone. Allow burner to return to room temperature before use.
USING THE ECOBURNER
- Rotate the handle fully anti-clockwise to MAX position, you should hear the gas start to flow.
- Place the EcoBurner on a flat surface and light the EcoBurner using a lighter or matches.
- Allow 60 seconds for the head to turn orange before moving the burner into place.
- Turn the handle & Listen for gas.
- Light the burner and let it glow orange.
TROUBLESHOOTING
If there is no gas flowing you should:
- Check the fill level using the filling station.
- Check if the OTV has been activated and reset if necessary.
- If the EcoBurner is overfilled, allow excess fuel to vent off in a well ventilated area.
An overfilled EcoBurner may “flare” (flame from head). This flaring will cease when the excess fuel is burnt off / removed.
DO NOT OVERFILL THE ECOBURNER. ALWAYS USE THE FILLING STATION. MAX WEIGHT OF A FILLED ECOBURNER 435g / 15.5 oz. www.ecoburner.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>