JASCO 51399 Ultra Pro In Wall Smart Dimmer Instruction Manual
- June 10, 2024
- JASCO
Table of Contents
JASCO 51399 Ultra Pro In Wall Smart Dimmer Instruction Manual
INSTALL THE APP
Remotely operate your smart dimmer with the easy-to-use UltraPro app. Follow the available instructions and resources to set up your smart device.
Scan the QR code above or search UltraPro on the Apple App Store or on Google Play.
**Set up account
Create an account in the UltraPro app
**
Install the smart device
Wire the smart dimmer following the provided instructions
Add devices, control the smart dimmer from anywhere and create schedules
Voice control
Compatible with Amazon Alexa and Google Assistan
Follow the steps in the Amazon Alexa or Google Assistant app to connect the
UltraPro app or select “Support” in the UltraPro app.
NOTE: If the LED is not flashing, ensure the air gap switch is flush with the paddle. Press the programming button for five seconds to reset device and start the pairing process. If the LED is still not flashing, turn of power at the circuit breaker or fuse box, remove dimmer and check wire connections.
SPECIFICATIONS — IMPORTANT!
- WFD3001
- Voltage: 120VAC, 60Hz
- Signal (frequency): 908.4/916MHz
- Maximum loads: 600W, 2-gang 500W or 3-gang 400W incandescent, 360W or 3A CFL/LED
- Operating temperature range: 32-104° F (0-40° C)
- For indoor use only
- Specifications subject to change without notice due to continuing product improvement
FEATURES
IMPORTANT! The fixture controlled by the Wi-Fi smart dimmer must not exceed dimmer ratings.
Get to you know your Wi-Fi smart dimmer
- Turn ON/OFF and adjust brightness manually or through the UltraPro app
- Compatible with Amazon Alexa and Google Home
- Auto-detect line/load terminals
- May be used in single-pole installation or 3-way wiring configurations
- Compatible with dimmable LED, CFL, incandescent and halogen lights
- Interchangeable paddle
- Uses a standard, rocker-style wallplate for single-gang installations (wallplate not included)
- Screw terminal installation — requires wiring connections for line (hot),load, neutral and ground. Traveler wire required for 3-way installation
A. Ground (green/bare)
B. Line or load (black)
C. Line or load (black)
D. Traveler (red/other)
E. Neutral (white)
F. Top rocker — press & release to turn dimmer on, press & hold to
increase brightness
G. Bottom rocker — press & release to turn dimmer of, press & hold to dim
H. Programming button — press for five seconds to enter pairing mode or
restore factory settings
I. Air gap switch — pull the air gap switch out to disconnect the power.
Push it all the way back in for normal operation.
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and lighting fixture at the service panel. All wiring connections must be made with the power OFF to avoid personal injury and damage to the switch. This device is intended for installation in accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada. If you are unsure or uncomfortable about performing this installation, consult a qualified electrician.
CHANGE PADDLE
This step is optional. Before installation, you may want to change the paddle
to match your wallplate or décor.
- Lift the air gap tab at the base of the paddle.
- Push the side tabs in on one side followed by the other to release paddle and lift it from the dimmer.
- Insert the air gap and side tabs and snap the new paddle into place.
REMOVE SINGLE-POLE SWITCH
-
Shut of power to the circuit at the circuit breaker or fuse box.
IMPORTANT! Verify power to switch box is OFF before continuing. -
Remove wallplate.
-
Remove the switch mounting screws.
-
Carefully remove the switch from the switch box DO NOT disconnect the wires.
-
Identify the following wires in the switch box:
A. Ground – Green/bare
B. Line (hot) – Black (connected to power)
C. Load – Black (connected to lighting)
D. Neutral – White -
Disconnect the wires from the existing switch – label wires according to the previous terminal connections.
SINGLE-SWITCH WIRING
WIRING REQUIREMENTS
Attach using the enclosure’s holes, strip insulation 5/8in. (16mm). UL
specifies the tightening torque for the screws is 12lbf-in (14Kgf-cm).
-
Connect green/bare wire to the GROUND terminal.
-
Connect the black wire from the light to either LINE/LOAD terminal.
-
Connect the black wire from the power source (hot) to the other LINE/LOAD terminal.
-
Connect the white wire to the NEUTRAL terminal – use jumper if necessary.
NOTE: The traveler terminal is only used for multi-switch wiring and is not used in a two-way system (one dimmer and one load) -
Secure the Wi-Fi dimmer into the switch box with the provided mounting screws – ensure wires are not pinched or crushed.
-
Install the wallplate.
-
The blue LED under the paddle flashes twice per second for up to 10 minutes to indicate the device is in pairing mode.
Insert wires into holes,
DO NOT wrap wires around screws
DO NOT remove screws
3-WAY SWITCH WIRING
The smart device supports standard 3-way switches for ON/OFF control and
Enbrighten, UltraPro or JascoPro Series add-on switches for full smart
functions from all locations. Below are instructions for installing a standard
3-way switch. See the add-on switch manual for add-on switch installation
instructions.
LINE SIDE (WI-FI DIMMER)
- Shut of power to the circuit at the circuit breaker or fuse box
- Remove line side wallplate
- Remove switch from line side switch box – DO NOT disconnect wires
- Label wire from the power source LINE
- Label one remaining wire traveler 1 – note the color of this wire for installation of the 3-way switch
- Label the other remaining wire traveler 2
- Disconnect all wires from the switch
- Connect green/bare wire to the GROUND terminal
- Connect the line wire to either LINE/LOAD terminal
- Connect the traveler 1 wire to the other LINE/LOAD terminal
- Connect the traveler 2 wire to the TRAVELER terminal
- Connect one end of a jumper to the bundle of neutral wires using a wire nut
- Connect the other end of the jumper to the NEUTRAL terminal
- Secure the Wi-Fi dimmer into the switch box with the provided mounting screws – ensure wires are not pinched or crushed
- Install the wallplate
- The blue LED under the paddle flashes twice per second for up to 10 minutes to indicate the device is in pairing mode.
LOAD SIDE (3-WAY SWITCH)
- Remove load side wallplate
- Remove switch from load side switch box – DO NOT disconnect wires
- Label wire from the light LOAD
- Label traveler 1 wire – recall the wire color from the Wi-Fi dimmer installation.
- Label traveler 2 wire
- Disconnect all wires from the switch
- Conecte el cable verde o pelado al terminal TIERRA
- Connect the load wire to the traveler 1 wire using a wire nut
- Connect traveler 2 to the LINE (hot) terminal
- Connect one end of a jumper to the bundle of line wires using a wire nut
- Connect the other end of the jumper to the COMMON terminal
- Secure the 3-way switch into the switch box – ensure wires are not pinched or crushed
- Install the wallplate
- Apply power to the fuse box or circuit breaker
Scan code for alternate 3-way wiring process
WARNING
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
CONTROLLING APPLIANCES
CAUTION: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO OTHER EQUIPMENT, DO NOT INSTALL TO CONTROL A RECEPTACLE, MOTOR-OPERATED APPLIANCE, FLUORESCENT LIGHTING FIXTURE OR A TRANSFORMER-SUPPLIED APPLIANCE
- ONLY USE TO CONTROL INCANDESCENT OR DIMMABLE CFL/LED BULBS • DO NOT EXCEED RATINGS
- DO NOT USE TO CONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.)
- NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT
- FOR INDOOR USE ONLY
WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7AM–8PM, M-F, Central Time or www.byjasco.com if the unit should prove defective within the warranty period.
FCC/IC
Suppliers Declaration of Conformity | Model #: 51399, 51413, 51414 | Jasco
Products Co., 10 E. Memorial Rd.,
Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC and Industry Canada license-
exempt RSS standards. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such
modifications could void the user’s authority to operate the equipment
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee interference will not occur in
a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment of and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
See product label for FCC/IC certification numbers. CAN ICES-3(B)/NMB-3(B)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>