ECOXGEAR SEI-INTRLED8KIT Interior LED Light Strips User Guide
- June 10, 2024
- Ecoxgear
Table of Contents
SEI-INTRLED8KIT Interior LED Light Strips
User Guide
Extreme Strip
INTERIOR LED LIGHT STRIPS
User Guide | Model: SEI-INTRLED8KIT
SEI-INTRLED8KIT Interior LED Light Strips
IMPORTANT:
- Please read the User Guide before installation and use.
- The Extreme Strip is compatible with the ECOXGEAR audio and LED lighting Eco System, which includes LED Cast and Eco Cast Innovations. Look for the LED Cast and Eco Cast logos on the growing family of ECOXGEAR and Sound Extreme audio and lighting solutions.
- The Extreme Strip must be controlled by a Sound Extreme product with LED Cast technology (sold separately).
- Do NOT make modifications to the product connectors.
- Do NOT connect this product to any other manufacturers’ LED controller.
WARNING:
- Connecting this product to any other manufacturer’s product may cause permanent damage to the product and shall void the warranty.
- Do NOT overly bend the LED strips.
**Extreme Strip Layout***
Connections
The Extreme Strip LED strips come pre-connected by a 3-pin connector. If the
strips are disconnected or if you want to rearrange the strips, please note
that the strips are directional. (Additional strips sold
separately).
IMPORTANT: When reconnecting the strips, verify that the arrows on each strip are facing the same direction AND ensure the arrows on the strip are facing away from the controller. The arrows on the strip MUST face away from the controller or other LEDCast product that the strips are connected to, otherwise they will NOT function.
Mounting Instructions
-
Each LED segment has two options to mount the strip to your vehicle’s body:
• 3M – double-sided tape
• Screw mounting holes at each end of the strip (screws included) -
The Interconnection Cable between two LED strip segments may be longer than the installation requires. Do NOT cut the cable and reconnect. Instead wrap the extra length on your vehicle and fasten the cable with the included zip ties. Please ensure the cable does NOT touch or drag on the ground AND is safely secured to prevent it from coming into contact with any moving parts.
Wiring Instructions
-
Run the LED Control Cable to a Sound Extreme product with LED Cast technology (sold separately), making sure the cable does NOT touch any moving parts on the vehicle. If the cable is longer than required do NOT cut the cable and reconnect. Instead wrap the extra length on your vehicle and fasten the cable with the included zip ties. Please ensure the cable does NOT touch or drag on the ground AND is safely secured to prevent it from coming into contact with any moving parts. You can also use the provided Cable Clips to keep loose sections of the cables from dangling. Mount the clip to your vehicle using the adhesive backing.
-
Connect the 3-pin male connector on the LED Control Cable to the LED control output 3-pin female connector on a Sound Extreme product with LED Cast technology.
IMPORTANT: To avoid potential electric damage to your strips or the LED controller, power off your Sound Extreme product with LED Cast technology before you make the connection. Align the arrow on both connectors, push-in, and screw the nut cap on the female connector. -
Once connected, you can change the Extreme Strip lighting effects via the connected Sound Extreme product, which can be controlled by either a RF remote or the Sound Extreme smartphone app.
Specifications
Total Length
in ( cm)
Unit Weight
lbs. ( kg)
Maximum Working Current
1.0A (12V Power Supply)
Storage Temperature
-4°F to 122°F / -20°C to 50°C
Operating Temperature
23°F to 95°F / -5°C to 35°C
FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: FCC’s RF Exposure guidelines, this equipment should be installed
and operated with minimum distance between 20cm the radiator to your body.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures: reorient or relocate the receiving antenna,
increase the separation between the equipment and receiver, connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected, consult the dealer or an experienced radio/TV
technician for help.
RF WARNING STATEMENT:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
IC STATEMENT :
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
PRODUCT USE AND PROTECTION:
Read and follow all instructions. Use only as intended.
The Sound Extreme unit is intended to be used indoors or outdoors and in land
or water environments. The unit has been tested to IP66 waterproofing
standards, which means the unit can be exposed to dust and water, but should
NOT be submerged underwater.
To prevent fire or shock, do NOT attempt to power this unit if it is wet or
you suspect water has entered the unit. In this situation, please return the
unit to Sound Extreme for a free assessment. If we have found that the unit
has carried water, we will repair or replace the unit free of charge.
SAFETY ADVISORY & WARNING:
Read and follow all instructions. Use only as intended.
CAUTION: Do NOT open to repair. A qualified technician must carry out
repair work.
ATTENTION: Do NOT connect to a Sound Extreme product with LED Cast
technology while the unit is wet. Make sure all connections are dry BEFORE
connecting to a power source. Failure to do so may result in electrical damage
to the unit and may void the warranty.
WARNING: Cancer and Reproductive Harm –
www.P65Warnings.ca.gov
ATTENTION: Do NOT dispose of in a landfill. Contact Sound Extreme at
www.gracesupport.com or a certified recycling
agent to dispose of the unit.
SAFETY:
This product has a limited life span of use and should be replaced when it
shows obvious signs of wear.
Do not modify or remove any original component parts of the speaker. Doing so
could cause damage to the unit, allowing water to ingress. A unit with water
ingress should not be charged due to potential risk of fire or shock.
Please exercise care and good judgment when using your Sound Extreme unit.
You should always
1.) Return the unit to Sound Extreme if you suspect water ingress into the
unit or if the unit has experienced a severe impact that may have affected the
integrity of the unit to take on water.
You should never
- Never power your Sound Extreme unit if you suspect water has entered the device. Powering a device with water inside could be potentially hazardous and cause fire or a spark.
- Never use your Sound Extreme unit if you have dropped it or thrown it against a hard surface which may have destroyed the integrity of the housing. In the event of a severe impact to your unit, please return the unit to Sound Extreme to review for potential damage.
- Never attempt to fix, repair your Sound Extreme unit . Please send it back to Sound Extreme for any assessments and repairs.
CARE, MAINTENANCE & PRECAUTIONS:
- Do NOT apply excessive force to any surfaces of the unit.
- Do NOT use or store the unit in places with high temperature.
- AVOID prolonged exposure to ultraviolet radiation (UV sunlight) and strong magnetic fields.
LIMITED MANUFACTURER’S WARRANTY:
The Extreme Strip is covered by a 1-year limited warranty that covers defects
in workmanship and / or materials for a period of 1 year from original
purchase date. This warranty does not apply to any products which have been
abused, neglected, modified or used for a purpose other than the one for which
they were manufactured. Please refer to the above care and maintenance
instructions for suggested care details. The warranty is valid only for the
original owner who purchases the unit from an authorized dealer. Transfers do
not qualify for warranty protection. Sound Extreme reserves the right to
replace any out-of-stock or discontinued product with a comparable product.
Discontinued products may not be available for warranty replacement. Any
contents are NOT covered by the limited manufacturer’s warranty. Warranty
terms may be revised without notification at the discretion of the
manufacturer. Please visit www.soundextreme.us
for additional product & warranty information.
Extreme Strip by Sound Extreme Inc., Houston, Texas.
Designed in Texas. Made in China.
What’s in the Box
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>