RPNB RPFS66 Large Fireproof Safe with Fingerprint Sensor Instruction Manual

RPNB RPFS66 Large Fireproof Safe with Fingerprint Sensor

Thank You for Your Recent Purchase
At RPNB Safe, we believe that everyone should have access to high-quality protection where they need it most. Whether you’re looking to protect your most cherished people or possessions, we are here to help you find the right safe for your needs. Our mission is simple: Create a safer world.

FS Series

Box Contents

1. RPNB® Touchscreen Fireproof Safe
2. Removable Shelf
3. Program Button
4. Living Bolts (3)
5. Dead Bolts (2)
6. Indicator Light
7. Fingerprint Sensor
8. Backlit Keypad
9. Backup Keys (2)
10. Expansion Bolt
11. Handle Spoke
12. Instruction Manual

Warning

• To prevent damage to your RPNB® unit or bodily injury, read the following safety precautions before using this unit.
• DO NOT PLACE OR STORE THE BACKUP KEYS INSIDE THE SAFE AT ANY TIME.
• IF THE BATTERY FAILS, YOU WON’T BE ABLE TO OPEN THE SAFE.
• DO NOT expose to extreme heat or cold. Battery power may be affected.
• DO NOT store loaded guns in this unit. Firearms are serious in nature and must be handled with respect. Store responsibly.
• ALWAYS check to make sure the safe is closed and locked when it is not in use.

Disclaimer

• Neither seller nor manufacturer shall be liable for unauthorized access, any injury, loss or damage to personal property direct or consequential, arising out of the use of, or the inability to use the RPNB® Safe.
• The user shall determine the suitability of the RPNB® Safe before the intended use and user assumes all risk and liability whatsoever in connection therewith, RPNB® Safe are not intended to protect against environmental hazards including fire and water.
• Be sure and follow all local and state firearm laws.
• DO NOT operate a firearm without proper training and experience.

Opening the Safe with the Backup Key

1. Locate the handle spoke in the yellow box hanging on the front door foam, mount 3 spokes to the
   handle hub.

2. Press the tab left and turn the lock cover counterclockwise. (see Figure A-1)

3. Insert one of your backup keys into the keyhole, turn it counterclockwise (see Figure A-2), at the same time turn the door handle clockwise to open the door. (see Figure A-3)

Battery Installation

1. With the lock cover remove, locate the battery compartment.
2. Connect a 9V alkaline battery (not included) to the battery connecting cap matching the polarity ( +/-) indicated. (see Figure B)
3. When the battery is connected correctly, the indicator light will light up once with 1 beep.
4. Place the lock cover, turn it clockwise back into its original position. (see Figure C)

NOTE:
When changing the battery, always hold the battery connecting cap while disconnecting or attaching the battery. Do not pull on the wires.

Master Code Programming

First-time users should change the default code as soon as possible to prevent unauthorized access to your safe. The code should be kept confidential.
Tips: Code Requirements

• Programming a new code will overwrite your previous code.
• Your code can be a minimum of 4 and a maximum of 6 digits.
• Two keys cannot be pressed simultaneously.
• Press any one of the “1,2,3,4” symbols until all keys (1-4) light to wake up the system before entering your passcode.

1. To get started, wake up the system and enter the default code

   • 1-2-3-4 on the keypad to open your safe.

2. With the safe open, press the Program Button once and release it, the indicator light will light up BLUE once with 1 beep. (see Figure D)

3. Enter your NEW master code.
   Press the Program Button once and release it, the indicator light will light up BLUE 2 times with 2 beeps.

4. Now test the passcode after woke up the system. If you set the passcode unsuccessfully, the indicator light will light up RED 5 times with 5 beeps, and the new code will not work. You must repeat the above steps to reset the code.

Fingerprint Registering

1. With the safe open, press the Program Button once and release it, the indicator light will light up BLUE once with 1 beep. (see Figure E)
2. Place your finger on the fingerprint sensor for the 1st of 4 scans. Remove your finger after the indicator light lights up BLUE once with 1 beep. Place your finger again over the fingerprint sensor until the indicator light lights up Blue once with 1 beep. You will repeat this process until the indicator light lights up BLUE 2 times with 2 beeps.
3. Now your fingerprint has been successfully registered.
4. Test your fingerprint. If you registered the fingerprint unsuccessfully, the new fingerprint will not work. You must repeat the above steps to re-register your fingerprints.

NOTE:

You cannot register more than 20 fingerprints. If the indicator light lights up RED 5 times with 1 O beeps when you register your fingerprint, it means the fingerprint storage capacity is full.

Helpful Programming Tips :

1. Place your finger on the center of the sensor (this allows the sensor to read where most of the fingerprint detail is located).
2. Adjust your finger slightly between scans for increased accuracy.
3. Excessive moisture, lotion, or dirt will affect your fingerprint and may cause inaccurate sensor reading.
4. If you are experiencing difficulty, try different fingers. Each finger is unique, and some fingers such as your thumb, contain more readable information than others.
5. To increase your success rate, please register the same fingerprint multiple times.

Registered Fingerprints Deleting

1. Press and hold the Program Button until the indicator light lights up BLUE 2 times with 2 beeps.
2. Now all previously registered fingerprints are erased.

Lock-Down System

• If you enter the wrong code or unregistered fingerprints, the indicator light will light up RED 5 times with 5 beeps.
• If the wrong code or unregistered fingerprint is entered 5 consecutive times, the safe will go into a lock-down mode for 5 minutes.
• During this time the indicator light will keep flashing RED, the keypad and fingerprint sensor will be temporarily disabled.
• The safe can still be opened by using the backup keys override.
• After 5 minutes, the safe will automatically resume normal operation.

Low Battery Warning

If the indicator light lights up BLUE 1 second, and then lights up RED 1 O times with 1 O beeps when opening the safe by electronic way, your battery level is critically low and your safe needs to be replaced the new battery.

Vibration Alarm Setting

Press and hold the number “4” for 4 seconds until you hear 1 beep and the indicator light lights up together.
NOTE:

• During the alarm, the keypad and fingerprint sensor will be temporarily disabled, the safe can still be opened by the backup keys or you can reinsert the battery.
• After the alarm is deactivated, you need to reset the above steps.

Locking the Safe

Turn the door handle clockwise to close the door.
Silence Mode Setting
To silence the audible sound of the electronics, hold the number “1” for 3 seconds, until the indicator light lights up. To unmute the keys, repeat this step, you will hear 1 beep and the indicator light lights up together.

Securing Your Safe
There are some mounting screws included to mount your RPNB® safe to a flat surface using the pre-drilled holes in the bottom.

Using the Mounting Screws

Tip: Make sure you have enough clearance for the lid to open properly before mounting the safe.

1. Use the mounting hole in the bottom of the safe to mark the desired mounting location.
2. Remove the cover, then use a pencil to mark the hole for drilling. (Figure G)
3. Position safe in place and install the expansion bolt through safe into pilot hole. Tighten screws.

IMPORTANT

Use the expansion bolt when there is a concrete wall surface. Use the clamping screw when there is a wooden wall surface.

How shall I view tutorial videos?

1. Go to our website at: www.rpnbsafe.us
2. Select “Support” on the footer navigation bar
3. Click “How to Use”
4. Click the Product Model you purchased

How shall I replace the keys?

1. Go to our website at: www.rpnbsafe.us
2. Select “Support” on the footer navigation bar
3. Click “Replace Keys”
4. Fill in the required information

How shall I order accessories?

1. Go to our website at: www.rpnbsafe.us
2. Select “Support” on the footer navigation bar
3. Click “Accessories”
4. Select the product model you purchased

More online at www.rpnbsafe.us under support

Customer Support/Warranty

Customer Support

If you have a problem with your RPNB® safe that is not answered in the this manual, we encourage you to email us: [email protected]

Linked Warranty (Terms and Conditions)

• RPNB® is committed to building high quality products and will make every effort to ensure our products are free from any defects. We guarantee your safe will be free of defects in materials or workmanship for a period of one year from the date of purchase.
• This warranty does not cover abuse, misuse, use in any manner for which is not designed, neglect, modification, damage inadvertently caused by the owner, accidents, and/or tampering.
• If you safe is determined to be defective and we are responsible for the cause we will have it repaired at our expense, or we will send a new replacement at no cost to you. You will be required to return your existing unit as well as all included accessories to
• RPNB® prior to replacement of the defective unit along with your proof of purchase.
• If it is determined your safe needs to be returned, our customer support team will provide you with return details.
• Please have the following information available when contacting us:
• Purchaser1s name and mailing address, email address, and phone number
• Online order number
• Detailed description of problem

HOW TO CONTACT

• Go to Your Orders, find your order in list, and click get product support.

You can e-mail the seller by doing the following:

1. Go to your account and find the order
2. Find your order item
3. Click get product support
4. Give the seller 24 hours to respond

• Please email us to get a special VIP discount code before your next order.
• Problem with the order? Please email us, and give us a chance to help you first.
• Do you love your new RPNB product? Help others find it by leaving a product review online!
• Email:[email protected]
• www.rpnbsafe.us
• Scan the QR code to learn more

Documents / Resources

| RPNB RPFS66 Large Fireproof Safe with Fingerprint Sensor [pdf] Instruction Manual
RPFS66 Large Fireproof Safe with Fingerprint Sensor, RPFS66, Large Fireproof Safe with Fingerprint Sensor, Fireproof Safe with Fingerprint Sensor, with Fingerprint Sensor, Fingerprint Sensor
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>