Shark 510-00044 Wireless Vertical Mouse User Manual

Shark 510-00044 Wireless Vertical Mouse

Thank you for choosing this special wireless vertical mouse.
Please read the user manual carefully when using this product.

Contents

• Wireless vertical mouse —- Xl
• User manual —- X1
• USB nano receiver — X1

Note
USB Receiver

Features

• Vertical mouse, worm bionic shape design
• Anti-skidding design
• Ergonomic design with removable palm, reduce hand and wrist pain

Installation

• Plug the USB connector for wired mouse (or USB Nano receiver for wireless version) to the USB port in the computer, after detecting successfully it will work normally.

Battery Installation

1. Open the battery cover.
2. Put the battery into the mouse in the correct direction.
3. Install the battery cover.

Note:

• In order to achieve the best economic effect, intelligent power-saving technology is adopted. When your mouse stops moving, it will switch to the power-saving mode automatically, and as this time passes, it will use less power.

Receiver Connection

1. Insert the USB Nano receiver into your computer by USB port.
2. After detecting ok by your computer, the mouse can work normally in ON mode.

Building Up the Connection Between the Mouse and Receiver

1. If your mouse cannot work normally, you can try to build up the connection again between mouse and receiver, as following steps:
2. Take out the Nano receiver from the computer and insert it again, it will detect automatically for about 15 seconds.
3. Keep the mouse in ON mode and with the battery in the correct direction.
4. Keep the effective distance within 1 O CM between the mouse and receiver.
5. Press the middle button (scroll wheel) and the right button at the same time for about 1~3 second, then release it. The connection is being built for about 1 O seconds.
6. lf cannot build up the connection in 10 seconds, please repeat the above steps.

sage Tips

• Please switch the ON/OFF button to be OFF mode if you do not use the mouse.
• Please take out the battery if you do not use the wireless mouse for a long time, and keep the battery in a cool and dry place.
• Please do not use the battery if leading, discoloration, distortion, or any other abnormity happens

Debugging Tips

• Check the receiver if is connected to the USB port.
• Check the ON/OFF button if in ON mode.
• Check the battery if is installed in the correct direction.
• Check the batter capacity if is enough.
• Check the effective distance between mouse the receiver and shorten it.
• Rebuild up the connection between the mouse and receiver.

Working Environment

• The radio signal can penetrate lignin, glass and other non-metallic objects, realizing 360 degree fee transmit. However, it cannot penetrate the metal materials. So please do not put the mouse and the receiver onto the metallic tabletop. The ideal distance is above20CM.
• Please be sure there is no big metal between the mouse and receiver, otherwise the connection will be affected. For desktop,
• USB extending port or front-set USB port is better.
• The receiver should be far away from the monitor, outside dies driver or other electronic products. 20 CM distance is suggested in order to prevent the radio disturbance produced by other electronic products.
• The optical mouse is suitable for operating media wooden, paper or cloth, but not for the lens cover, such as glass and smooth rubber.
• A mouse pad is needed in such an environment.

Warranty

• This product is guaranteed against any manufacturing defect, as defined on the D.Lgs. February 2, 2002, No 24. In case of failure, please contact the retailer where you purchased it. You can be found at www.adj.it for the guarantee of a standard.
• Please use the product only for the purpose for which it was designed. It is forbidden any other use or modification.

This product complies with the following directives:

• DIRECTIVE 2014/53/EU on the harmonization of the laws of the Member States relating to the making available on the market of radio equipment;
• DIRECTIVE 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
• The declaration of conformity for this product is visible on www.adj.it site, on the product page.
• The symbol of the crossed-out trash indicates that the product, at the end of its useful life, must be treated separately from domestic waste and must be taken to a recycling center for electrical and electronic equipment or delivered to the seller when buying a replacement.
• The separate waste collection contributes in preventing possible adverse effects on the environment and health and promotes the recovery of materials it is made.
• You are responsible for assigning the equipment in question at the appropriate waste disposal center.
• For more detailed information contact your local waste disposal service or the shop where it was purchased. Anyone who does not carry the product in a recycling center for electrical and electronic waste shall be punished with an administrative penalty provided by law on the illegal disposal of waste.
• Additional compliance information:
• To obtain additional information about the compliance, go to the ADJ website: www.adj.it/certification or contact ADJ Customer Support to the following e-mail address: supporto@adj.it
• Made in China – Imported and distributed by lot Tenologie s.r.l.
• Via della Faeta, 1 – 00030 San Cesareo (RM) – ITALY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>