TRANIS46722 Tracer Razor 2 Paper Shredder Instruction Manual
- June 4, 2024
- Tracer
Table of Contents
Instruction Manual
Tracer Razor 2 paper shredder Instructions for use
Tracer Razor 2
Tracer Razor 2 paper shredder
SPECIFICATIONS
- Cutting Style: Strip cut
- Entry Width: 220 mm
- Shred Capacity: 6 sheets (A4 paper)
- Input: AC 230V, 50Hz, 0.9A
- Power: 190W
- Operating cycle: 2 min on / 40 min off
- Net weight: 1.4 kg
NAMES OF COMPONENTS
- 3 – Position slide switch for AUTO, OFF, and REV.
- Paper entry: Put paper into this entry to shred.
- Credit card entry: Put credit card into this entry to shred.
- Wastebasket: It is used to undertake shredded paper.
SAFETY SYMBOLS
Warning: Please pay more attention to the safety instruction, before operating the machine otherwise wrong operation will result in danger to users.
| The product is not intended for use by children (the product is not a toy)|
|
Avoid hair touching the docu-SY ment feed opening.
---|---|---|---
| R) Avoid touching the document feed opening with your hands.| | Do not
insert paper clips or staples into the infeed slot.
| Avoid clothing and long necklace- ces or bracelets touching the document
feed opening| | Keep aerosol products away (for products incorporating a
universal (brush) motor.
INSTALL GUIDE
- Put the machine on a flat table.
- Insert the power plug into the corresponding electric socket and make sure that the working voltage complies with the supplying voltage.
OPERATION GUIDE AND REMARKS
- Set the slide switch to the “AUTO” position, at the same time, the machine is on standby; put the shredding paper, vertically into the entry, thereafter, it starts up automatically and does shredding; it returns to standby automatically after finishing.
- When a jam is caused by inserting too much paper, or you want to withdraw the paper immediately at the normal shredding, please set the slide switch to “REV”, at the same time, the machine does the reverse rotation and returns the paper that has not been shredded; then put the switch to “OFF”.
- To ensure your machine has a long use life and exerts good shredding function, please notice the ma- maximum number of shredded paper. For continuous paper shredding in large quantity, please minimize the consecutive using time to 2 minutes. Hence, you can properly protect your shredder for higher efficiency.
- If the machine works continuously or spasmodically for a long time, it may pause because the inside temperature increases continuously. After resting for a period of time, it can work again.
- Please do not put clips, adhesive paper, adhesive tapes, or cloth into the paper entry in order to avoid damaging the blades or lowering the shredding performance.
- If you want to clean the wastebasket or the machine, or the machine is not used for a long time, please cut off the electric power and unplug the machine.
SAFETY OPERATION GUIDE
- Before use, please r e a d introduction manual carefully ;
- Keep ties, jewelry, hair, etc. away from the machine to ensure personal safety;
- Do not place the machine near the heat sources o r in the humid environment for a long time;
- Please use the machine near the electric socket to unplug it easily;
- When cleaning the machine or repairing the damaged plug, please unplug it from the electric socket at first;
- The machine must be far away from children and pets;
- If the machine is not to be used for a long time, please cut off the electric power and unplug it.
ABNORMITY AND ) COUNTERMEASURE IN USE
| Index | Abnormities | Cause | Countermeasure |
|---|---|---|---|
| 1 | After finishing the normal shredding, it runs ceaselessly yet. | Too much |
scrap paper in the wastebasket, so that the just scrapped paper cannot fall
and leave in the entry.| 1. Cut off the power, and empty the wastebasket.
2. Cut off the power, and press the scrapped paper down to make them away
from the machine head.
2| Paper feed or positive rotation is normal, but there is still some scrapped
paper hanging at the exit after finishing.| The slots of the blades clamp the
scrapped paper.| Set the slide switch to “REV” (if needed, please clean the
scrapped paper at the exit).
3| It can’t work if feeding paper follows withdraw-wing paper.| Some scrapped
paper lock automatic inductive devices.| Set the slide switch to “REV”.
4| Some paper is in the entry, but the shredder does not work.| After feeding
the paper, any corner of the paper is inserted, but the rest doesn’t touch the
automatic inductive device.| Adapt to the position of the feeding paper and
make it touch the automatic inductive device.
5| The paper is jammed, and the machine stops rotating.| 1. The number of
inserted paper is too larger than the limitation
2. Locked rotor makes the motor overheat and then the temperature protection
set takes action.| 1. Set the slide switch to “REV” and withdraw the
shredding paper.
2. Unplug the plug and let the machine stop for a while.
6| The machine doesn’t start after inserting a sheet of paper or stop running
when the paper is being inserted.| The paper is too thin, too soft, humid, or
too crinkly to activate the automatic inductive device.| 1. Fold the paper
and then
insert it.
2. Set the slide switch to “REV”.
Producent:
Megabajt Sp. z 0.0., ul. Rydygiera 8, 01-793 Warszawa
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>