DOREMiDi UTD-10 USB To DMX Cable Instructions
- June 10, 2024
- DoreMidi
Table of Contents
DOREMiDi UTD-10 USB To DMX Cable
Introduction
USB to DMX cable (UTD-10) is a high-quality light control converter designed by DOREMiDi. UTD-10 has DMX and RDM functions, which can convert DMX/RDM to USB and connect to a computer. UTD-10 has a communication indicator light, which is convenient for operation and debugging. In addition, UTD-10 has a built-in protection circuit to protect the computer and external light control equipment, and an external magnetic ring shield to improve the anti- interference ability.
Appearance
- XLR plug, connect RDM/DMX equipment.
- USB connector, connect to Windows, Mac, Linux, and other equipment.
- USB indicator light, after the USB connection, the indicator light is always on.
- IN indicator, the RDM input indicator flashes after receiving data from RDM equipment.
- OUT indicator, DMX output indicator, flashes after sending DMX data output.
Product Parameters
Name | Description |
---|---|
Model | UTD-10 |
Length | 2 meters |
Weight | 100g |
USB Plug | USB2.0 standard full-speed USB plug |
XLR plug | Standard three-pin XLR plug |
Indicator Ligh | USB work indicator, RDM input/DMX output indicator |
Compatible System | Windows, Mac, Linux, etc. |
Steps for usage
-
Connection: Connect the USB USB-A plug of UTD UTD-10 to the PC, and the XLR plug to the RDM/DMX device device.
-
Install the driver: Generally, Win8/Win10 will automatically discover the USB USB-DMX device. If it is not found, you need to install the driver manually. Driver download
- link: https://ftdichip.com/drivers/vcp vcp-drivers/
- Select the driver to download according to the system situation, as shown in the figure for part of the driver:
-
Software settings: Take FreeStyle X2 as an example
-
Install FreeStyle X2 software:
FreeStyle software download link: www.freestylerdmx.be -
Set FreeStyle to connect to UTD-10:
Open “Setup→FreeStyle Setup”, select “JMS USB2DMX” and “FT232R USB UART”, and then select “Save” to save the settings. -
Add/remove DMX/RDM equipment:
Open “Setup→Add/Remove fixtures” and add/remove RDM/DMX devices according to the picture.
-
Precautions
- This product contains a circuit board
- Rain or immersion in water may cause the product to malfunction
- Do not heat, press, or damage internal components
- Non-professional maintenance personnel are not allowed to disassemble the product
- The working voltage of the product is 5VDC, using a voltage lower or exceeding this voltage may cause the product to fail to work or be damaged
Q&A
-
Question: Recognized after connecting to a computer.
Answer: Please make sure that the computer has been correctly installed the driver, the driver link: https://ftdichip.com/drivers/vcp-drivers/ -
Question: After connecting to the DMX lamp, the lamp cannot be controlled normally.
Answer: Please make sure that the DMX channel that occurs is consistent with the lamp. -
Question: After opening the software, the interface fails to open, or the software does not recognize the UTD-10 cable.
Answer: Re-plug the UTD-10 cable, or use another USB interface, or restart the application software.
If the problem is not resolved, please contact customer service.
Manufacturer:
-
China Show (Shenzhen) Technology Co., Ltd.
-
Address: Room 9A, 9th Floor, Kechuang Building, Quanzhi Science and Technology Innovation Park, Shajing Street, Baoan District, Shenzhen, Guangdong Province
Customer Service -
Email: info@doremidi.cn.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>