WOMEDUAL 36W Outdoor Air Conditioner Fence Privacy Screen Instruction Manual
- May 15, 2024
- womedual
Table of Contents
OUTDOOR PRIVACY FENCE
Assembly Instructions
STEP ONE
STEINVENTORY BOX CONTENTS & PREPARE ASSEMBLY TOOLS
The following tools will help you do a better job of assembling your fence.
Please prepare them in advance of your assembly.
If there is any problem in the assembly, you can contact us.
*Note: You can choose the right tool for different soils
|
---|---
▶ Electric screwdriver (highly recommended)| ▶ Gloves x1 (complimentary)
|
▶ Mallet (to aid in installation)| ▶ Ruler or measuring tool (to ensure
location)
When you receive your shipment,
please count the number of each product in the package.
If there are missing or damaged. Please contact us by email or Amazon. We will
provide you with a solution.
STEP TWO
**ASSEMBLE ONE PANEL
**
STEP 2.1
Slide (20/22) Rails (B) into
the routed holes in the Left Post (A1).
36 “W X 45 “H: 20 pcs
48 “W X 48 “H : 22 pcs
STEP 2.3
Slide (1) Right Post (A2)
over the opposite ends of the slats and rails.
Tap Left Post (Al)and Right Post (A2) bar properly with a mallet so that Rails
(B) bar is completely inside Left Post (Al1)and Right Post (A2) bar hole.
STEP THREE
INSTALL SCREWS AND CAPS
*Note:* Place the adjusted panel on a flat surface.
Note: Due to the sensitive nature of the pvcnotches, do not tap on any
of the notches after screwing In the screws!
STEP 3.1
Note: Please don’t worry if the Rails (B) are crooked when screwing in
the screws. It will not affect the aesthetics nor the use. Solution: Turn the
screw back a little and the Rails (B) will stay square.
Drive total of 4 Self-Drilling Stainless Steel Screw (F
1 2 3 4) into the Left Post (A1)and Right Post (A2).Use an electric
screwdriver.
Note: Before installing the Screw (F 1 2 3 4)you need to make sure that
Rails (B) is fully into the Post (A1) rod.Prevent Rails (B) from slipping out
of Post (A2) during the installation of screws.
STEP 3.2 Install 2 top caps (E). Press fit Left Post (A1)and Right Post
(A2).
“Note:** Use a mallet to gently tap in the cover to ensure a tight fit.
STEP FOUR
ASSEMBLE THE SECOND SCREEN PANEL
Repeat Steps TWO & THREE In to assemble the second screen.
STEP FIVE
INSTALL PANEL INTO THE GROUND
*Select the screen mounting location.
*Note:* It Is recommended to install on tight ground. It Is not
recommended to install on loose ground such as planted flowers, as this will
not ensure strong stability.
Note: When staking the ground, it is recommended to put something in the
center. For example, paper shells. This will effectively prevent the ground
stake from bending.
STEP 5.1**
- Locate the first ground stake(D).
Pointed section facing down. Use a mallet to drive in. Tap into the ground about 9.45 inches. The top leaks out 6.3 inches.
STEP 5.2
Measure the distance betweer the two holes atthe bottom ofthe fence (36
inches/48inches).
STEP 5.3
Determine the location of another ground stake (D). Repeat the tapping
procedure to complete the installation of both ground.
*With the help of a ruler, ensure ground stakes(D) are properly leveled.
STEP 5.4 Insert the holes in the bottom Left Post (A1)and Right Post (A2)
of the fence into the upper end of the ground stakes (D). It’s recommended to
use the aid of a mallet as an assistant.
STEP SIX
INSTALL ANOTHER PANEL INTO THE GROUND
STEP 6.1
Confirm
how the two panels will be used. Straight Line Application or Corner
Application.
Repeat Step 5. Complete the floor mounting of the second panel.
STEP 6.2
2.Drive total of 2 Self-
Drilling Stainless Steel Screw (F 5 6 5″6″) into the bottoms of Left Post
(A1)and Right Post (A2) Use an electric screwdriver.
STEP SEVEN
CONNECT THE SCREENS
STEP 7.1
- Straight Line Application:Connect the screens as shown below using Joiner Clips (C) and stainless steels screws(G).
STEP 7.2 - Corner Application:Connect the screens as shown below using Joiner Clips (C) and stainlesssteel screws(G).
*Note: There are no pre-drilled holes for the joiner clips to allow for
greater customization duringassembly. When driving in the screws, you need to
make sure that the screws are upright at 90degrees. It can not be crooked.
Mail: xhjtradecn@hotmail.com
LOT-
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>