SHARP FX-J80U Air Purifier Owner’s Manual

SHARP FX-J80U Air Purifier

The air purifier draws in room air through the air inlet, circulates it through a pre filter, an Active carbon deodorizing filter and a true HEPA filter inside the main unit, and then discharges it through the air outlet. The True HEPA filter can remove 99.97% of dust particles as small as 0.3 microns that pass through the filter and also helps absorb odors. The Active carbon deodorizing filter gradually absorbs odors as they pass through the filter. Some odors absorbed by the filters will break down over time, causing additional odors. Depending on usage conditions, and especially if the product is used in environments significantly more severe than a normal household, these odors may become noticeable sooner than expected. If these odors persist, replace the filters.

NOTE

• The air purifier is designed to remove air-suspended dust and the odors.
• The air purifier is not designed to remove harmful gases such as carbon monoxide contained in cigarette smoke.
• The air purifier may not completely remove an odor if the source of the odor is still present.

Declaration of Conformity SHARP AIR PURIFIER FX-J80U. This device complies with Part 18 of FCC rules. Responsible Party: SHARP ELECTRONICS CORPORATION 100 Paragon Drive, Montvale, NJ 07645, U.S.A. This Wi-Fi adapter complies with Part 15 of the FCC rules. Operation is subject to the following two conditions

• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.

REGISTER YOUR PRODUCT
Registering your new product is easy and offers benefits that help you get the most out of your Sharp product including

• Convenience: If you ever need warranty support, your product information is already on fi le
•  Communication: Stay up to date with important note cations and special offers from SHARP.
• Support: Quickly access support content including Owners Manuals, FAQ’s, How to Videos, and much more.

3 EASY WAYS TO REGISTER TODAY

SCAN

Use the camera or QR code scanning application on your smart phone.

ONLINE
Visit our sites to learn more about your product at sharpusa.com and sbl.sharpusa.com

CALL US
US 800-BE-SHARP 800-237-42777

PRODUCT SUPPORT

If you have questions about the setup or operation of your product, please refer to the corresponding section within this manual. Additionally, visit www.sharpusa.com/support to access exclusive content about your product including

• FAQ’s and How-To Videos
• Find or Request Service
• Downloads including the Installation Guide, Spec Sheet.

CONTACT US
If at any time you have questions or comments concerning your SHARP product, please contact the SHARP Customer Assistance Center. We are available to assist you through multiple contact methods for your convenience

EMAIL
Available 24/7
US: sharpusa.com

CHAT ONLINE
Mon-Fri: 7am-7pm CST Sat-Sun: 9am-7pm CST

CONSUMER LIMITED WARRANTY
the Product  when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction. In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer. The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING TH WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp. The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND PUERTO RICO. TO OBTAIN SERVICE, SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP, OR VISIT OUR WEBSITE AT www.sharpusa.com
SAVE THE PROOF OF PURCHASE AS IT IS NEEDED SHOULD YOUR AIR PURIFIER EVER REQUIRE WARRANTY SERVICE.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

WARNING

• Use the product only for intended household use.
•  Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure they do not play with the appliance.
• Never operate the product if the power cord or plug is damaged or the product is malfunctioning or damaged.
• If the power cord or plug is damaged, it must be replaced by the manufacturer, its service agent or a Sharp authorized Service Center in order to avoid a hazard.
• Contact the nearest Service Center for any problems, adjustments, or repairs.
• Do not repair or disassemble the product yourself.
• Follow the instructions a to h below for the power cord or plug.
• It may cause short circuit, excessive heat, electric shock or fire.
• Use only AC 120 volt outlet.
• Do not use the product if the power code or plug is damaged or the connection to the wall outlet is loosened.
• Always turn off the product before unplugging the power plug.
• Always unplug the product before moving or maintaining it, opening the back panel, changing the filters and whenever the product is not in use.
• Be sure to pull the power plug and not the power cord.
• Do not touch the power plug with wet hands when inserting or unplugging from the wall outlet.
• Periodically remove dust from the power plug.
• Always observe the following not to damage the power cord.
• Do not run cord under carpeting.
• Do not cover the power cord with throw rugs, runners, or similar coverings.
• Do not put heavy things on the power cord or pinch it.
• Do not run the power cord under furniture or other appliances.
• Run the power cord away from traffic area and where it will not be tripped over.
• The product has a polarized plug one blade is wider than the other.
• To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way.
• If the plug does not fit fully in the outlet, reverse the plug.
• If it still does not fit, contact a qualified electrician or service person. Do not attempt to defeat this safety feature.
• Do not use this product near gas appliances, fire places, candle fire, incense or sparks from lit cigarettes.
• Do not operate the product in a room with flammable gas, such as oily residue or chemical fumes.
• Do not expose the product to rain, or use near water, in a bathroom, laundry area or other damp location.
• Do not insert fingers or foreign objects into the air inlets or air outlets.
• Do not look into the air outlets.

NOTE

Radio or TV Interference

If the product should cause interference to radio or television reception, try to correct the interference by one or more of the following measures

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the product and radio/TV receiver.
3. Connect the product into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

CAUTIONS CONCERNING INSTALLATION

1. Place the product on a level and stable surface with sufficient air circulation.
2. When placed on heavy carpet, the product may vibrate slightly.
3. Avoid a location where the sensors are exposed to direct breeze or draft if the product has sensors.
4. The product may not operate properly.
5. Avoid use in locations where furniture, fabrics, or other items may come in contact with and restrict the air inlets and/or outlets.
6. Avoid locations exposed to direct sunlight. It may cause to change shape or color of the product.
7. Avoid locations where the product is exposed to condensation or drastic changes in temperature.
8. Use under appropriate conditions between 32 – 95 ºF 0 – 35 ºC.
9. Avoid use in locations where greasy or oily smoke is generated. (such as in a kitchen, etc.
10. The main unit surface may crack and the sensors may malfunction as a result.
11. The dust collecting ability of the product is effective even when the product is as close to 1.2 inches (3 cm) from the wall, but the surrounding walls or floor may get dirty.
12. Please place the product at a distance from the wall.
13. The wall directly behind the air outlets and the floor or rug on which the product placed may become dirty over time.
14. When using the product for an extended period of time at the same location, periodically clean the walls, the floor or the rug.

CAUTIONS CONCERNING FILTER

• Take out the filters from the plastic bag before placing the filter in the main unit.
• Do not operate the product without the filters properly installed.
• Do not wash and reuse the True HEPA filter and the Active carbon deodorizing filter.
• Washing will not improve filter performance and can also cause electric shock or operating malfunctions.
• Do not operate the product in a rooms where aerosol insecticides are present.
• It may cause the odor of insecticide may be remained in the product and emitted from the air outlets.

CAUTIONS CONCERNING OPERATION

1. Do not block the air inlets or air outlets.
2. Always operate the product in an upright position.
3. Always hold the handle of the product when moving it.
4. Always lift up the product when moving it on easily damaged flooring, an uneven surface, or carpet.

CAUTIONS CONCERNING MAINTENANCE

• Clean the exterior with a soft cloth only.
• Do not use volatile fluids and/or detergents.
• The main unit surface may be damaged or cracked with strong corrosive cleansers, benzine, paint thinner, polishing powder or grease.
• In addition, the sensors may malfunction as a result if the product has sensors.
• Do not scrub the back panel (pre-filter) hard during its maintenance.
• When replacing filters or any accessories, use specified parts.

PART NAMES 1

FRONT

BACK

2 locations: Left and Right

7| Front Louver
8| Back Panel (Pre-Filter)
9| Air Inlet
10| Active Carbon Deodorizing Filter
11| True HEPA Filter

12

| Sensor Filter Sensor Internal

Odor / Sensitive dust /

Temperature / Humidity

13| Unit

Plasma cluster Ion Generating Unit

14| Unit Holder
15| Unit Cover
16| Unit Cleaning Brush
17| Power Cord, Plug

OPERATION PANEL

Press either button  to start.

FRONT DISPLAY

For details on items marked with refer to the Wi-Fi Connect Guide. * Press and hold 3 seconds or longer.

Button, Indicator Light white

5| Plasmacluster Ion SPOT Button, Indicator Light – white

6

| Fan Speed Button, Indicator Lights – white

Press 3 sec.

Plasmacluster Ion ON/OFF Button

7| TIMER Button

Press 3 sec.

FILTER RESET Button

8|

Press 3 sec.

CHILD LOCK Button

9| Child-Lock Indicator Light  white
10| Light Sensor

11

| Air Quality Monitor

Indicates the air purity of the room in 5 levels with color changes.

****Red

12| Wi-Fi Indicator
13| SHARP CLOUD Indicator

14

| PM2.5 Monitor

Indicates the sensitive dust sensor detects microscopic dust.

TURN OFF

Orange

Red Clean

Impure

15

16

| Dust Monitor Odor Monitor

Continuously monitors dust or odor in the air and changes color depending on purity

---|---
17| Unit Replacement Indicator
18| Filter Maintenance Indicator
19| ON Timer Indicator
20| OFF Timer Indicator
21| Plasmacluster Ion Indicator

22

| DISPLAY

The displayed numbers are approximate values.

PM2.5 Monitor

PM2.5 10μg/m3 to 499μg/m3 is displayed.

9μg/m3 500μg/m3

or less or more

Wattage Monitor

Indicates wattage by current operation.

Humidity Monitor

Humidity 20% to 90% is displayed

20% 90%

or less or more

Temperature Monitor

Temperature 32oF to 122oF is displayed.

31oF 123oF

or less or more

Timer Monitor

Indicates setting time or remaining time of ON/OFF timer.

FILTER INSTALLATION

To maintain the quality of the filter, it is installed in the main unit and packaged in a plastic bag.. Be sure to stop operation and unplug the product before filter installation or replacement.

Remove the back panel

Take out the filters from the plastic bag Install the filters in the correct order as shown Install the back panel. Record the date when you start or replace the filters on the back cover

OPERAOPERATION  1

START/STOP

Unless the power plug has been unplugged, the operation will Auto Resume in the previous mode it was operating in. Example: if the power is lost during operation, the operation will resume to previous operation mode and settings if power is restored.

AUTO MODE

The fan speed is automatically controlled depending on the 3 detections.Dust / Odor / Light)

NOTE
When light control is set to Auto, front display, air quality monitor will automatically switch ON or dims based on room brightness.

PLASMACLUSTER EXPRESS CLEAN MODE

The air purifier releases Plasmacluster ions at max air flow for 10 minutes. After that, it operates for 50 minutes on high fan speed. When the operation finishes after 60 minutes, the product will return to the prior operation mode. It is able to change to other modes during this operation. The Plasmacluster ion cannot be turned OFF.

PLASMACLUSTER ION SPOT MODE

Use this mode when you want to remove adhering odor, germs, and other substances from clothes, sofas and curtains.

NOTE

• The product emits high density Plasmacluster ions only in the forward direction.
• The product produces stronger air for 8 hours.
• When the operation finishes, the product will return to its prior operation mode.
• The Plasmacluster ion cannot be turned OFF.

FAN SPEED BUTTON

SLEEP

• The product will operate quietly, and the fan speed will automatically switch depending on the amount of impurities in the air and room brightness.
• The front display and air quality monitor automatically switches dims or turns OFF based on room brightness.
• Room is bright: light is dimmed
• Room is dark: light is OFF

POLLEN:

The dust sensor is automatically increased and quickly detects impurities such as dust and pollen and cleans the air powerfully.

OPERATION 2

ON TIMER

Set the ON TIMER when you would like to schedule the air purifier to turn on after a certain number of hours with the product OFF

Every time you press the TIMER button, it will change the auto start time in the following sequence NOTE
If you have already set the timer using the App, you cannot set the timer using the product.

OFF TIMER

Set the OFF TIMER when you would like to schedule the air purifier to turn off after a certain number of hours. Every time you press the TIMER button, it will change the auto shutdown time in the following sequence:

NOTE
If you have already set the timer using the App, you cannot set the timer using the product.

SELECTING DISPLAY

With the product ON

CHILD LOCK

The operation panel will be locked.

NOTE
It is possible to turn Wi-Fi off while in Child Lock Mode.

PLASMACLUSTER ION ON/OFF

When the Plasmacluster function is ON, the Plasmacluster ion indicator light is on.

OPERATION 3

HOW TO CHANGE VARIOUS SETTINGS

You can change the functions listed in the table below.

Turn the product OFF

Select

Press for 3 sec.

You can select F or A.

Set

Select Function Number

Select Setting Number

Finish the setting.

Light control F1

You can select the brightness of the front display and air quality monitor.

| Turn off 01

Dim 02

Auto (default) 03

Light automatically switches based on room brightness.

Auto resume F2

This model has Auto Resume function, where the operation resumes at the previous operation mode and settings if the power is restored.

| Cancellation 02

ON default

Adjusting sensor sensitivity F3

F4

F5

Light sensor

|

Low 01

Standard default 02

High 03

| Sensitive dust sensor| |
Odor sensor| |

CARE AND MAINTENANCE 1

• To maintain optimum performance of this air purifi er, please clean the product including the filter periodically.
• Be sure to stop operation and unplug the product before any maintenance or replacing accessories.

MAIN UNIT / BACK PANEL

FILTER MAINTENANCE INDICATOR

The filter maintenance indicator light will turn on* when it is time to maintain the back panel pre filter. This indicator light will turn on after approximately 720 hours operating. (30 days × 24 hours = 720 hours. After maintenance, connect the power plug to the wall outlet and press POWER ON/OFF button, then TIMER button for 3 seconds.

MAINTENANCE

Wipe with a dry, soft cloth

Remove the dust gently with a cleaning tool such as a vacuum cleaner.

How to clean hard to remove dirt.

Back panel

Add a small amount of neutral detergent to water and soak for about 10 minutes. Do not apply excessive pressure when scrubbing the back panel. Rinse off the neutral detergent with clean water. Completely dry the filter in a well ventilated area.

Sensor filter

1. Remove the back panel.
2. Remove the sensor filter.
3. If the sensor filter is very dirty, wash it with water and dry it thoroughly.

CARE AND MAINTENANCE 2

TRUE HEPA FILTER / ACTIVE CARBON DEODORIZING FILTER

REPLACEMENT AND MAINTENANCE CYCLE

Filter Name| Maintenance Cycle| Max Service Life| Replacement Filter Model
---|---|---|---
True HEPA Filter| ****

Whenever dust accumulates, when odor emanates from the air outlet, or once a month.

| ****

2 years

| FZ-J80HFU
Active Carbon Deodorizing Filter| FZ-J80DFU

According to Japan Electric Manufacture’s Association JEM 1467, the Max service life is based on the equivalent condition of the smoke from 5 cigarettes per day whereby the dust collection/deodorization power is reduced by half compared with that of new filter. It is recommended to replace the filter more frequently under more severe conditions.  Designated App notifies when filters or Plasmacluster ion generating unit should be replaced according to usage.

MAINTENANCE

Remove the dust on the filters TRUE HEPA FILTER

Maintain only the tagged surface. Do not clean up the opposite surface. The filter is fragile, so be careful not to apply too much pressure.

NOTE
Do not wash the filters. Do not expose to sunlight. Otherwise these filters may lose efficacy.

ACTIVE CARBON DEODORIZING FILTER

Both surfaces can be maintained. The filter is fragile, so be careful not to apply too much pressure. Some odors absorbed by the filters will break down over time, causing additional odors. Depending on usage conditions, and especially if the product is used in environments significantly more severe than a normal household, these odors may become noticeable sooner than expected. Replace the filter in those cases or if dust is unable to be removed after maintenance

REPLACEMENT

Please consult your dealer for purchase of replacement filter. Use only filter designed for this product.Record the date when you replace the filters on the back cover. Scan the QR code for
product information and accessories

FZ-J80HFU: 1 unit

Disposal of Filters

Please dispose of the replaced filter according to the local disposal laws and regulations. True HEPA Filter materials: Polypropylene, Polyethylene Active Carbon Deodorizing Filter materials: Polypropylene, Polyester, Activated carbon. Do not wash and reuse replaced filter.

PLASMACLUSTER ION GENERATING UNIT

MAINTENANCE

Remove the unit cover, and pull out the unit holder.

Remove dusts from the electrode section.

Insert the unit holder in the main unit, and install the unit cover. NOTE

• Do not clean with anything other than the unit cleaning brush. Doing so could lead to failures in the unit.
• A bent electrode could be cut off and dropped during the cleaning process, but it will not change the performance.
• Do not touch the electrode directly. Doing so could lead to pain/itching.
• Do not transform the electrode section. Doing so can damage it.
• Do not touch the connection terminals. Doing so can damage them.

UNIT REPLACEMENT INDICATOR

When the total operation time exceeds 17,500 hours, the unit replacement indicator will flash to indicate that the Plasmacluster ion generating unit needs replacement.

Operating time|
---|---
17,500 hours

Flash slowly

|

Replace the Plasmacluster ion generating unit

19,000 hours

Flash quickly

|

Stop the emission of the Plasmacluster ions.

The replacement time is not related to the selected operation mode.

REPLACEMENT

Consult your dealer when purchasing a replacement Plasmacluster ion generating unit.

Model: IZ-C90MU

Remove the claw of unit holder ( 1 ), and remove the Plasmacluster ion generating unit ( 2 ).

Disposal of Plasmacluster Ion Generating Unit

Dispose of used Plasmacluster ion generating unit according to local laws and regulations materials: Polybutylene terephthalate, electronic parts.

TROUBLESHOOTING

Before calling for service, please review the list below, since the problem may not be the product malfunction.

Odor and smoke persists

Check the filters. If they appear to be extremely dirty, clean or replace them.

Air discharged from the product has an odor

Check to see if the filters are extremely dirty. Clean or replace the filters.

The product does not operate when cigarette smoke is in the air

• Make sure the product is installed in a location in which the sensors can detect cigarette smoke.
• Check to see if the sensitive dust sensor openings are blocked or clogged. If they are blocked or clogged, clean the sensor filter or the back panel.

Smell from a new filter

Immediately after removing the plastic bag, a slight odor may occur. This odor is not harmful for filter performance or human exposure.

The product makes a clicking or ticking sound

The product may make clicking or ticking sounds when it is generating ions.

The air quality monitor is blue even when the air is not clean

The air may have been dirty when the product was plugged in. Unplug the product, wait one minute, and then plug the product in again.

The air quality monitor is red even when the air is clean

Dirty or clogged the sensitive dust sensor openings interfere with sensor operation. Gently clean the sensor filter or the back panel.

The air quality monitor changes color frequently

The air quality monitor automatically changes color when the sensitive dust sensor and odor sensor detect impurities. If you are concerned about the change, you can change sensor sensitivity.

The filter maintenance indicator light is on

Whenever after performing maintenance of the filters, connect the power cord to an outlet and press POWER ON/OFF button, then press the FILTER RESET button.

The front display is turned off

When light control is set to “Turn off”, the light is always off. If you do not want the light to be off, set light control to Auto or Dim setting.

The product’s display does not match weather report or another

hygrometer or thermometer in the room

Outdoor and indoor as well as the home environment (the volume of traffic nearby, number of stories in home, etc.) may cause a reading different than those data. There is a difference in the level within the same room.

When should sensor sensitivity be changed?

Please change sensor sensitivity as follows according to each case.

Light sensor

• Change to Low when the front display still lights up brightly even if it turns dark in the room.
• Change to High when the front display lights up dark even if it is bright in the room.

Sensitive dust sensor

• Change to Low when PM2.5, Dust or Air Quality Monitor displays in red frequently.
• Change to High when PM2.5 or Dust Monitor doesn’t light up or Air Quality Monitor stays in blue even if it is dusty in the room.

Odor sensor

• Change to Low when Odor Monitor displays in red frequently.
• Change to High when Odor Monitor doesn’t light up even if there is some odor in the room.

ERROR DISPLAY

Flash quickly

| The communication between SHARP server and the air purifier is not available.

Please check the Wi-Fi Connect Guide for details.

|

| Is the Plasmacluster ion generating unit inserted properly?

Pull out the Plasmacluster ion

generating unit and insert it to the

end again, and then operate again.

---|---|---|---

| The concentration of Plasmacluster ion is descending.

Maintain the electrode section of

the Plasmacluster ion generating

unit.

|

| Unplug the product, wait one minute, and then plug the product in again.

SPECIFICATIONS

Fan Speed Operation

| Fan Speed Adjustment| MAX| MED| SLEEP
Rated Power W| 70| 27| 3.2
Fan Speed CFM| 321| 170| 35
Noise Level dBA 1| 49| 45| 15
Standby Power (W)| 0.9 (When Wi-Fi adapter is ON.)

0.7 (When Wi-Fi adapter is OFF.)

Recommended Room Size*2| 502 sq. ft. (47 m2)
CADR (Dust / Smoke / Pollen)| 334 / 324 / 361

Filter type

| Dust collection| True HEPA Filter
Deodorization| Active Carbon Deodorizing Filter
Cord Length| 6.6 ft 2.0m

Dimensions

| 16.4 in W × 11.5 in D × 28.7 in H

416 mm W × 291 mm D × 728 mm H

Weight| 23.8 lbs. (10.8 kg)

1 Noise level is measured based on the JEM 1467 standard of the Japan Electrical

Manufacturers Association

2 Size of a room which is appropriate for operating the product at maximum fan speed.

Standby Power

This product consumes a minimal amount of power while in standby mode. For energy saving, unplug the power cord when the product is not in use.

SAFETY / PRECAUTIONS

In case of remote operation from outside, you may not be able to check air purifier current condition or the area around it and the situation concerning anyone possibly staying there, so please adequately confirm safety before use. Make sure the electric plug is fully inserted into a power socket, and there is no dust on the plug or in the socket hole. It may cause heat, combustion, fire, etc., due to poor contact or contact failure. Make sure beforehand that although there are some wind changes, no negative impact will occur to the environment inside the room. (such as whether there is anything flying easily in the wind) Because the wind may cause something to fall down, resulting in fires, wounds, defacement of household belongings.

CAUTION FOR USE

• Agreement with Terms of Service is needed to use App.
• App will be periodically revised because of version upgrade.
• Screens and illustrations in this book are for explanation, there are some differences to the real product.
• In the case of bad connection, the App may not be able to control the air purifier.
• The current operation of the air purifier may not be accurately reflected on the App.
• Locking smartphone display is recommended to avoid wrong operation.
• Although the App is free, communications expenses for download of dedicated App and operation with smartphone or tablet are customer’s obligation.

CAUTION FOR Wi-Fi

Caution for usage about electrical wave

• In case of the usage at the following place, the operation cannot be guaranteed : Near Bluetooth wireless communications device using the same frequency (2.4GHz) as this product or specified low power wireless device.
• Also in the place like magnetic field of the device such as microwave oven, or the place with static electricity or the place radio disturbance is occurred, it may not be available temporarily due to weak electrical wave.
• Wireless connection and performance cannot be guaranteed for all routers or housing environment.
• At the following places, it is likely electrical wave cannot reach or is disconnected.
• Inside of the building made with concrete, reinforcing steel or metal / near the obstruction / near the wireless communications device applying the same frequency.
• Wi-Fi of this product corresponds to channel 1 – 13. It’s not available to communicate with the routers set up to other channels.

Caution for personal information related to Security

• Using Wi-Fi device has the possibility of interception as long as using electrical wave regardless of secret code setting.
• Wi-Fi has the advantage of free LAN connection in the service area because of the communication between this product and the router applying electrical wave. On the other side, intercept of communication or unfair intrusion are likely to occur because electrical wave reaches everywhere in the certain area through the obstructions (e.g. walls).
• Do not connect to the device or network without App to authority.
• The Wi-Fi function of this product should be initialized in case of disposal or handover to a third person.
• The Wi-Fi function of the unit should be initialized in case of handover from a third person to avoid illegal access of outsider.

How to set Wi-Fi ON / OFF after completing the initial settings

When turning off Wi-Fi

When turning on Wi-Fi again

Wi-Fi Connect Guide and set up the connection with the router again. If the product is already registered to your smartphone, you do not need to register again.

NOTE

• Wi-Fi ON / OFF can also be set from
• Wi-Fi adapter ON/OFF”. (Page 19)
• In this case, Wi-Fi connection with the router will be automatically restored.
• Reconnection to the Wireless Router may take a few minutes to complete, after turning Wi-Fi on again.

HOW TO CHANGE VARIOUS SETTINGS 1

You can change the functions in the table below. Follow Steps 1 – 4 to select the Function.

Step 1

Turn the product OFF.

Step 2

Step 3

Select A

Step 4

Select Function Number GO BACK

No| Function|
---|---|---
A1| Wi-Fi adapter ON/OFF|
A2| Wi-Fi connection with a router|
A3| Link settings with a smartphone|
A4| Initialization of Wi-Fi function|
A5| Update|
A6| Confirmation of MAC address|
A7| Display Wi-Fi network status|
A8| AP

Access Point mode

|

Step 5

Please  for the detail of each functions.

Step 6

Finish the setting.

Wi-Fi adapter ON/OFF

• Select  A1 by following Steps 1 – 4.
• Select Setting Number.

OFF: Stoppage of Wi-Fi function AND ON: Start the Wi-Fi function

Complete

When  02 is selected, the square rotates on the display until the setting is completed. When setting is completed A2  is displayed

 A2 Wi-Fi connection with a router

Select by following Steps 1 – 4. After is displayed, press the Wi-Fi Protected Setup (WPS) button of the router.

Once connected, receiver level will be displayed

A connection error is occurring if is displayed. Please confirm the router and try again.

Complete

HOW TO CHANGE VARIOUS SETTINGS 2

 A3 Link settings with a smartphone

After  CP is displayed, start the App and register the air purifier.

A connection error is occurring if is displayed. Please confirm the router and try again.

Complete

 A4 Initialization of Wi-Fi function

After  AC is displayed press  AUTO button.

A connection error is occurring if  DE is displayed. Please confirm the router and try again.

Complete

Please delete the device registration from the App when initializing the air purifier which is already connected to the Wi-Fi.

 A5 Update

Start the App then tap at the Home screen and select Update.

UP will be displayed.  Follow instructions on the App screen. will be blinking during update. A connection error is occurring if is displayed. Please confirm the router and try again.  Air purifier will automatically go off after completion of the update. Go off It may take a few minutes to complete the update.

  A6 Confirmation of MAC address

Press Plasmacluster Express Clean button to display MAC address

For example In case MAC address is “12 : 34 : 56 : AB : CD : EF

Complete

HOW TO CHANGE VARIOUS SETTINGS 3

 A7 Display Wi-Fi network status

After displaying for a few seconds, network status of Wi-Fi adapter will be displayed.

Please turn on Wi-Fi adapter.

bU| Router is not registered

Please perform the Wi-Fi connection with the router.

CU| Link settings with the App is not performed Please perform the link setting with the smartphone.
AE| Wi-Fi adapter network error

Please turn off Wi-Fi adapter and turn on again after a while.

bE| Network error between the air purifier and the router

Please confirm the network status of the router.

CE| Network service error

Please turn off the air purifier and confirm the internet status, then try again.

Complete

 A8 AP (Access Point) mode

Perform Wi-Fi connection of the air purifier and the router based on the App screen and blinks while setting the connection between the product and the router. Once connected, receiver level will be displayed.

A connection error is occurring if bE is displayed. Please confirm the router and try again.

SPECIFICATIONS

• Wireless LAN: IEEE802.11b/g/n
• Frequency range: 2.4GHz frequency band

Intellectual property rights for this product 1

Software structure

Software installed in this product is structured with multiple independent software components, each of them has our or third-party’s copyright. Software of our development and free software Among the software components of this product, for software we developed or created and incidental documents has our copyright. And they are protected
by copyright law, international regulation and other related laws. Also this product uses software components distributed as free softwar  with third- party’s copyright.

Obligation of license indication

Some software components installed in this product are required to indicate the license by those copyright holders. License indications of such software components are as below: Expat Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper Copyright (c) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the
following conditions. The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISINGFROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE Wslay The MIT License Copyright (c) 2011, 2012 Tatsuhiro Tsujikawa Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files the Software  to deal in the Software without restriction, including without limitation the rights to use, copy,
modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the
following conditions

• The above copyright notice and this permission notice shall be included in all
  copies or substantial portions of the Software.

• THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND,

• EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
  NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
  WHETHER IN AN ACTION OF CONTRACT,TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
  OTHER DEALINGS IN THE SOFTWARE Copyright (C) 2000-2009 Josh Coalson Copyright (C) 2011-2014 Xiph.Org Foundation

• Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other
  materials provided with the distribution.

• Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

• THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,

• INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

• DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

• NCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
  POSSIBILITY OF SUCH DAMAGE. Copyright (c) 2001, 2002 Swedish Institute of Computer Science All rights reserved

Redistribution and use in source and binary forms, with or without modification are permitted provided that the following conditions are met

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other
   materials provided with the distribution.

3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.

4. THIS SOFTWARE IS PROVIDED BY THE AUTHOR “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
   WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE
   LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES(INCLUDING, BUT NOT LIMITED TO,
   PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
   ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

This file is part of the lwIP TCP/IP stack Copyright 2010 Serge A. Zaitsev Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to  following conditions The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AN NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT  HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR  OTHER DEALINGS IN THE SOFTWARE.  All Rights Reserved Licensed under the Apache License, Version 2.0 the License you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.0. Unless required by applicable law or agreed to in writing, software distributed
under the License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for
the specific language governing permissions and limitations under the License. Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. Neither the names of the above-listed copyright holder(s) nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Intellectual property rights for this product 2

Software structure

Software installed in this product is structured with multiple independent software components, each of them has our or third-party’s copyright. Software of our development and free software Among the software components of this product, for software we developed or created and incidental documents has our copyright. And they are protected
by copyright law, international regulation and other related laws. Also this product uses software components distributed as free software with third- party’s copyright.

Obligation of license indication

Some software components installed in this product are required to indicate the license by those copyright holders. License indications of such software components are as below:

Expat

Copyright c 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper Copyright (c) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the
following conditions

• The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

• THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
  FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

• The MIT License Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT  HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

• Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
• Neither the name of the Xiph.org Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other
   materials provided with the distribution.

3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES(INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE  POSSIBILITY OF SUCH DAMAGE. This file is part of the lwIP TCP/IP stack.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the
Software without restriction, including without limitation the rights to use, copy modify, merge, publish, distribute, sublicense, and/or sell copies of the Software,
and to permit persons to whom the Software is furnished to do so, subject to the following conditions. The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.0 Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the

All Rights Reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of
   conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other
   materials provided with the distribution.

3. Neither the names of the above-listed copyright holder(s) nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTIONHOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE O OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Intellectual property rights for this product 3

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. Neither the name of KTH nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY KTH AND ITS CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NO LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL KTH OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOTLIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OFTHE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  Permission to use, copy, modify, and distribute this software for any purpose
without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software. THIS SOFTWARE IS BEING PROVIDED AS IS, WITHOUT ANY EXPRESS  OR IMPLIED WARRANTY. IN PARTICULAR, THE AUTHOR MAKES NOREPRESENTATION OR WARRANTY OF ANY KIND CONCERNING THEMERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE. Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTOR “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,  BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of  conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OFSUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OFTHE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or othermaterials provided with  the distribution.
3. The name of the company may not be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY ARM LTD “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL ARM LTD BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other
   materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Red Hat Incorporated Copyright (c) 1994-2009 Red Hat, Inc. All rights reserved. This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License. Thisprogram is distributed in the hope that it will be useful but WITHOUT ANY WARRANTY expressed or implied, including the implied warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. A copy of this license is available at http://www.opensource.org/licenses. Any Red Hat trademarks that are incorporated in the source code or documentation are not subject to the BSD License and may only be used or replicated with the express
permission of Red Hat, Inc.

University of California, Berkeley
Copyright (c) 1981-2000 The Regents of the University of California. All rights reserved. Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met

• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
• Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER INCONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Redistribution, modification, and use in source and binary forms is permitted provided that the above copyright notice and following paragraph are duplicated in all such forms.
This file is distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. (4) (formerly GPL for fr30) The GPL is no longer applicable to the fr30 platform. The piece of code referencing the GPL has been officially relicensed. 5) Advanced Micro Devices Copyright 1989, 1990 Advanced Micro Devices, Inc. This software is the property of Advanced Micro Devices, Inc (AMD) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by AMD. AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH
REGARD TO THIS SOFTWARE. IN NO EVENT SHALL AMD BE LIABLE FOR  INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS SOFTWARE. So that all may benefit from your experience, please report any problems or suggestions about this
permission to use, copy, modify, and distribute this file for any purpose is hereby granted without fee, provided that the above copyright notice and this notice appears in all copies, and that the name of Hewlett-Packard Company not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission. Hewlett-Packard Company  makes no representations about the suitability of this software for any purpose (10) Hans-Peter Nilsson Copyright (C) 2001 Hans-Peter Nilsson Permission to use, copy, modify, and distribute this software is freely granted, provided that the above copyright notice, this notice and the following disclaimer are preserved with no changes.
THIS SOFTWARE IS PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR  IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE.

National Semiconductor Corporation
Copyright (c) 2004 National Semiconductor Corporation The authors hereby grant permission to use, copy, modify, distribute, and license this software and its documentation for any purpose, provided that existing
copyright notices are retained in all copies and that this notice is included verbatim in any distributions. No written agreement, license, or royalty fee is required for any of the authorized uses. Modifications to this software may be copyrighted by their authors and need not follow the licensing terms described here, provided that the new terms are clearly indicated on the first page of each file where they apply.

References

• Simply Better Living – SHARP | Simply Better Living
• Sharp Electronics | SharpUSA
• Apache License, Version 2.0
• Licenses – Open Source Initiative
• Sharp Electronics | SharpUSA
• Sharp Electronics - Sign in
• Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>