SounDigital SD5000-1 EVO 5 Digital Amplifier 5000 Watts Owner’s Manual

June 11, 2024
SOUNDIGITAL

SounDigital logo SD5000-1 EVO 5 Digital Amplifier 5000 Watts
Owner’s Manual

INTRODUCTION

DEAR CUSTOMER,
CONGRATULATIONS ON ACQUIRING A PRODUCT WITH THE HIGHEST QUALITY AND TECHNOLOGY!
You have just purchased a SounDigital product of the highest technology and quality, so we thank you for your confidence.
Class D Amplifiers:
Class D amplifiers have as main characteristics the audio quality, efficiency, application versatility and compact design. Following are the advantages of these features:
Audio Quality – In the past, Class D products had limited response and for higher frequencies, Class AB products performed better, but their efficiency was very low.
The new technologies introduced by SounDigital resulted in a Class D amplifier with high efficiency and superior Class AB performance.
Efficiency – SounDigital Class D amplifiers have total efficiency (output

  • power source) greater than 70%, which guarantees lower battery consumption and less heating.
    Application Versatility – The flat full-frequency response of SounDigital amplifiers allows them to be used in all car sound systems. Meeting the demands with extreme quality.
    Compact Design – The high efficiency and high technology applied, allows SounDigital amplifiers to be very compact, facilitating installation in vehicles where space is limited.
    IMPORTANT INFORMATIONS
    On this manual you will learn about the product, its features and characteristics, in order to obtain the best result and to be able to enjoy your music with SounDigital quality and power.
    To better understand and take advantage of all the functions of the product and use it safely, read this manual carefully and if you have any questions, consult our support by email info@soundigitalusa.com.

PACKAGE CONTENTS

  • 01 5000.1 EVO5 Amplifier
  • 01 Installation quick guide with warranty card
  • 01 Promotional sticker

SAFETY INSTRUCTIONS

To prevent injuries to the user or damage to the amplifier, read all safety instructions written on this manual;
If you are insecure about the installation of this equipment, get in touch with our tech support or with a professional specialized in car audio installation;
Before proceeding with the installation of any electric equipment on your vehicle, unplug the negative (-) terminal of the battery to avoid fires, injuries or damages;
Use your sound system safely. The continuous exposure to sound pressures over 85dB may cause irreversible hearing damage;
This equipment is for use in automotive DC voltage batteries between 12.6 and 14.4 volts. Before installing the equipment, check voltage of the batteries;
Do not install the amplifier in places exposed to water, dirt or humidity;
Choose a ventilated place to install the amplifier and avoid blocking the side ventilation windows;
Mount the amplifier in a secure way. Avoid mounting it on metallic parts of the vehicle, because it may cause ground looping (noise);
Make sure that the location chosen for the amplifier installation does not effect the operation of the vehicle;
When passing cables through metallic walls, use rubber O-rings to avoid cable cutting and short-circuits;
Clean the amplifier periodically with brush or dry cloth to assure the thermal efficiency of the heatsink;
This product may reach temperatures over 60°C/140°F. Make sure it is cold before touching it;
Be careful when making holes in the vehicle. Make sure you are not making holes in the fuel tank, brake lines or electrical cables of the vehicle;
Make sure the cables are properly secured throughout the installation;
Wear gloves, safety glasses and and all necessary PPE during the installation of SounDigital amplifiers.
THIS “WARNING” SIGN ALERTS THE USER OF IMPORTANT INFO. NOT FOLLOWING THIS INSTRUCTIONS MAY CAUSE INJURIES TO THE USER OR DAMAGE TO THE EQUIPMENT.

ASSEMBLING AND DISASSEMBLING THE PLASTIC COVER

The plastic covers have the function of finishing and hiding the amplifier fixing screws. To disassembling and assembling them, follow the instructions below.
DISASSEMBLING OF THE PLASTIC COVERSounDigital SD5000-1 EVO 5 Digital
Amplifier 5000 Watts - fig 1

  1. Carefully pull out the top of plastic cover to release the upside latches, as shown in the picture 1.
  2. Slide up the plastic cover in a continuous movement to remove it.

*Merely illustrative images.
ASSEMBLING THE PLASTIC COVERSounDigital SD5000-1 EVO 5 Digital
Amplifier 5000 Watts - fig 2

  1. To fit the plastic cover back, carefully insert the point A of the plastic cover into point B of the amplifier, slowly sliding it down.
  2. Gently press the sides of the top of the plastic cover towards the bottom of the amplifier until you hear a clicking noise.

*Merely illustrative images.

PANELS DESCRIPTION

SounDigital SD5000-1 EVO 5 Digital Amplifier 5000 Watts - fig
3

1| Right Channel
Left Channel| Audio input – High Level
(To connect to the speaker output of the head unit)
---|---|---
2
3| Right Channel
Left Channel| Audio inputs – RCA connectors
4| –| Variable Gain Control
5| –| Variable “LOW PASS” filter control (50Hz ~ 6kHz)
6| –| Variable “SUBSONIC” filter control (5Hz ~ 80Hz)
7| –| Variable “BASS BOOST” control 50Hz (0dB ~ +12dB)
8| –| Remote level control connector
9
10
11| Red
Yellow
Blue| “PROTECTION” LED indicator
“CLIP” LED indicator
“POWER ON LED” indicator

PANELS DESCRIPTION

SounDigital SD5000-1 EVO 5 Digital Amplifier 5000 Watts - fig
4

12 Positive speaker connector (+)
13 Minimum connection impedance indicator
14 Positive power supply connector (+12VDC)
15 Negative speaker connector (-)
16 Remote power supply connector (REM)
17 Negative power supply connector (GND)

ELECTRICAL DIMENSIONING AND AUDIO INPUTS

ELECTRICAL DIMENSIONING
For proper operation of your SounDigital amplifier, you need the proper dimensioning of the electrical system and the cables used.
The table below shows the minimum section of GND cables, +12VDC cables and speaker output cables according to the power generated by the amplifier.

5000
WRMS| POWER CABLE (+12VDC)
GROUND CABLE (GND)| 50mm² – 0 AWG
---|---|---
SPEAKER CABLE| 5000.1 EVO 5 1Ω| 2 x 10mm² – 7 AWG
5000.1 EVO 5 2Ω| 2 x 6mm² – 9 AWG

We recommend the use of ONLY OFC (Oxygen Free Copper) Cables on the installation of our products. CCA cables must not be used.

AUDIO INPUTS

RCA inputs ** All RCA Inputs must be connected for the all channels to work properly. If the signal source is mono type, use “Y” cable at the input.
High Level input ** All High Level Inputs must be connected for the all channels to work properly.
High level input must be used when the main unit does not have RCA outputs.
When High level inputs is used, no remote connection is required, the amplifier recognizes the audio signal and switches on.
If your source unit is not able to turn on the amplifier through the High level input, the remote input should be connected normally.
RCA AND HIGH INPUTS SHOULD NOT BE USED SIMULTANEOUSLY OR YOU MAY DAMAGE THE AMPLIFIER.

INSTALLATION SEQUENCE

BEFORE PROCEEDING WITH THE INSTALLATION, UNPLUG THE NEGATIVE TERMINAL FROM ALL OF THE BATTERIES, TO AVOID FIRE, DAMAGE TO THE AMPLIFIER AND THE USER HIMSELF.
Mount the amplifier in such a way you have access to the connectors;
Install the power cables in the vehicle properly, starting from the battery to the fuse holder or circuit breaker, use the cable with the appropriate size. Make all connections, install fuse holders or circuit breakers, but without placing the fuses or with the circuit breakers in the “OFF” position;
THE MAXIMUM DISTANCE FOR THE INSTALLATION OF THE FUSE/CIRCUIT BREAKER IS 12 INCHES (30cm) AWAY FROM THE BATTERY.
Connect the power cables in to the amplifier, observing the polarity. Connect all the positive cables from the fuse holder or circuit breaker to the positive conector of the amplifier and all the negative power cables from the batteries to the negative connector of the amplifier;
The ground cable must be as short as possible and must be connected to the vehicle chassis and the battery negative;SounDigital SD5000-1 EVO 5 Digital
Amplifier 5000 Watts - fig 7 Install the signal input cables in a proper way, distant from the power cables;
Connect the RCA or the high level signal input cables to the head unit and amplifiers;
Install the audio output cables with the appropriate section, distant from the power and audio input cables;
Connect the audio output cables to the amplifier and speakers respecting the positive (+) and negative (-) polarities;
Install the remote cable with the power cables, using 1.5mm² (15 AWG) cable or thicker;
Connect the remote power cable to the amplifier’s “REM” terminal at the main unit’s remote power output (when not using the high level signal inputs);
Before powering the system, verify all the connections and make sure there are no mistakes or short-circuits on the power and ground cables;
Reconnect the ground of the batteries;
Check if the head unit is turned off and then place the fuses in the fuse holders or switch the circuit breakers on;
Turn on the main unit and the amplifier will turn on the “ON” LED indicating that it is in operation.

WIRING DIAGRAM

**** All RCA Inputs must be connected for the channels to work properly.SounDigital SD5000-1 EVO 5 Digital Amplifier 5000 Watts - fig
8

Model Minimum Impedance
5000.1 EVO5 1Ω
5000.1 EVO5 2Ω

SD RLC / GAIN SETTING

*EXTERNAL LEVEL CONTROL – SD RLC (NOT INCLUDED)**

The SD RLC is an easy-to-install external level control accessory that allows you to tune the level of SOUNDIGITAL amplifiers that have remote level control.
In SD RLC, you can adjust the amplifier level without having to lean over and adjust the gain setting on the amplifier and can monitor the “CLIP” LED which is also available on the accessory.
Necessary equipament:
Digital AC voltmeter;
Media with sine wave test tone 60Hz recorded at 0db;
Screwdriver 1/8″ ( for gain set).
Set up procedure
Turn the gain control all the way down;
Disconnect the output cables from the amplifier outputs;
Turn off all processing (bass, treble, loudness, EQ, etc.);
Set the source unit volume to 3/4 of full volume;
Set the source unit’s fader control to center position;
Set the variable “LOW” crossover in 6kHz and the “SUBSONIC” in 5Hz;
Use a 60 Hz sine wave;
Increase the gain control until the “CLIP” LED starts blinking;
Return the gain to the limit where the “CLIP” LED stops blinking and remains off;
Once you have adjusted the amplifier to the correct voltage output, turn off the source unit and reconnect the speaker(s).
Download the tracks for set up in https://soundigitalusa.com/tracks-for-set- up/SounDigital SD5000-1 EVO 5 Digital Amplifier 5000 Watts - fig
10

BASS BOOST AND CROSSOVER SET UP

Using Bass Boost
The Amplifier Bass Boost setting enables the user to boost the sound intensity at low frequencies of the sound system, where boost intensity can be adjusted.
This is a semi-parametric equalizer type circuit with ”Q” value for the fixed filter, with an intensity boost adjustment from 0 to +12dB (16 times), and a central frequency adjustment of the filter in 50Hz, making it versatile for several types of sound systems. How to Adjust Bass Boost
Reproduce your favorite song and set the boost intensity between 0dB and +12dB at the variable control level according your preference.
How to Adjust the Crossovers
The use of the two associated filters can form a bandpass filter, as in the figure below, where the point “A” is defined in the “SUBSONIC” crossover and the point “B” is defined in the “LOW” crossover.SounDigital SD5000-1 EVO 5
Digital Amplifier 5000 Watts - fig 14To set the “SUBSONIC” variable control between 5Hz and 80Hz (“A”) where you want to perform the subsonic cut filter; Set in the “LOW” variable control between 50Hz and 6kHz (“B”) where you want to perform the low pass cut filter;

TECHNICAL SPECS

PARAMETERS 5000.1 EVO5 1Ω 5000.1 EVO5 2Ω
Power RMS @ 4Ω** 2178W 3300W
Power RMS @ 2Ω** 3300W 5000W
Power RMS @ 1Ω** 5000W N/A
Frequency Response (-3dB) 5Hz ~ 6kHz 5Hz ~ 6kHz
Low Pass filter (12dB/oct) 50Hz ~ 6kHz 50Hz ~ 6kHz
Subsonic (12dB/oct) 5Hz ~ 80Hz 5Hz ~ 80Hz
Operating Voltage 8V ~ 16V 8V ~ 16V
SNR 90dB 90dB
Input Sensitivity (RCA) 0.2V ~ 2V 0.2V ~ 2V
Input Sensitivity (High Level input) 1.2V ~ 12V 1.2V ~ 12V
Current Draw (music) 230A 230A
Current Draw (max.) 461A 461A
Total Efficiency 86% 86%
Damping Factor (@100Hz nominal impedance) >2000 >2000
Power Cable 50mm² (0 AWG) 50mm² (0 AWG)
Speaker Cable  2 x 10mm² (7 AWG)  2 x 6mm² (9 AWG)
Fuse* (music) 250A 250A
Recommended battery (minimum) 250Ah 250Ah

*It is mandatory to install the fuse at a maximum distance of 12 inches from the battery.
Power at 12.6V @ 60Hz with a maximum THD of 1%.
POWER RATING ACCORDING TO CTA-2006 INDUSTRY STANDARDS
DIMENSIONAL DATA![SounDigital SD5000-1 EVO 5 Digital Amplifier 5000 Watts

SounDigital logo YOUR MUSIC. YOUR POWERSounDigital SD5000-1 EVO 5
Digital Amplifier 5000 Watts - icon 2 WWW.SOUNDIGITALUSA.COM
SOUNDIGITALUSA
SOUNDIGITALUSA
CODE.: 1000750341-001/SEP2022

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SOUNDIGITAL User Manuals

Related Manuals