Paruu X2 Wearable Breast Pump User Manual

X2 Wearable Breast Pump
User Manual

PRODUCT DESCRIPTION

1.1 Parts List

1. Flange (25mm)
2. Linker
3. Diaphragm
4. Pump Motor
5. Milk Bottle
6. O-Ring| 7. Valve
8. Flange Insert (21mm)
9. Flange Insert (17mm)
10. Bottle Lid
11. Type-C Charging Cable
12. Bra Adjuster
---|---

1.2 Controls
Flashing light: Low battery Note:

• This product has a built-in Lithium polymer battery. When the leftmost indicator light flashes , we recommend that you use a certified 5V 2A Power Adapter to charge the device as soon as possible.
• You may check the remaining battery power by counting how many indicators light up in standby mode when pressing the “+” and “-” buttons at the same time for 2 seconds. Each indicator light represents around 20% of the remaining power.

INTENDED USE

2.1 Indications for Use
The wearable breast pump helps lactating women express and collect milk from their breasts. Meanwhile, it can alleviate breast engorgement, and address breast milk supply issues. The device is intended for a single user.
2.2 Operating Life

1. The operating life of the device is defined to be approximately 500 hours.
2. The expected operating life of the replaceable washable components is 2-3 months, It also depends on how frequently the parts are used and washed.
3. It’s recommended to replace the washable components after long-term storage or before next pumping session.

IMPORTANT SAFETY INFORMATION

3.1 Warnings

• If you are a mother who is infected with Hepatitis B, Hepatitis C or Human Immunodeficiency Virus (HIV), pumping breast milk will not reduce or remove the risk of transmitting the virus to your baby tl rough your breast milk.
• Powered breast pumps that are designed for single users should never be rented or shared.
• Pregnant women should not use the breast pump, as pumping can induce contractions or premature labor.
• The Wearable Breast Pump (X2) is not intended to be used during air transport.
• This is a single-user product, use by more than one person may present a health risk and voids the warranty.
• Inspect for damage, clean and sterilize washable components that come into contact with your breast and breast milk prior to first use.
• Clean all parts that come into contact with your breast and breast milk, and inspect for damage after every use.
• During normal use, areas of the Parru wearable pump may warm up. If your pumping environment is at the upper operating temperature limit (+30°C / +86°F) for the maximum session time (30 minutes), the temperature of the Flange may reach up to +45°C / + 113°F.
• Do not store wet or damp parts, as mold may grow.
• Do not immerse the pump motor in water or other liquids. Wipe with a clean, damp cloth.
• This product contains small parts and a cable that may present a hazard. Keep out of reach of children.
• Only use Parru manufactured parts with Parru pump, including the charging cable, do not substitute.
• It’s recommended to use an adaptor compatible with both IEC 60601-1 and your regional power source.

3.2 Precautions

• Before each use, visually inspect the individual components for cracks, chips, tears,discoloration or deterioration. In the event that damage to the device is observed, please discontinue use until the parts have been replaced.
• If discomfort is felt, then suction can be broken by inserting a finger between the breast and the flange.
• If irritation or discomfort occurs, discontinue use and see a healthcare provider.
• If the power adapter casing or wiring becomes loose, separated, or frayed, stop use of the power adapter immediately and contact the device manufacturer. Stop using the device immediately if you note any smoke or burning from the pump unit or power adapter.
• Monitor milk level during pumping to ensure overfill does not occur.
• If you feel excessive warmth from the X2 Wearable breast pump while pumping, stop pumping immediately and remove pump.
• Always inspect all parts before use.
• Always ensure all parts are completely dry before assembling.
• Do not place the pump motor in the fridge or freezer.
• Do not use flammable materials while using Parru pump or connecting Parru pump to a charger.
• Do not use Parru wearable pump while sleeping or overly drowsy.
• Using a breast pump should not cause pain. Do not try to express with an intensity setting that is too high or uncomfortable. If excessive discomfort or pain is felt during pumping, break the seal between the flange and the breast tissue and end the session.
• Contact your healthcare professional if you express minimal or no milk, or if expression is painful.
• For assistance with correct flange sizing and comfort, pls see section 4.3 or talk to a lactation consultant or breastfeeding specialist.
• Extra care is necessary when using the Parru pump in the vicinity of children.
• Parru pump should not be used while lying down, or engaging in strenuous exercise or activities with risk of harm.
• Always break the seal between the flange and the breast tissue and end the session before removing Parru pump from your breast.
• Do not expose Parru pump or components to direct sunlight.

GETTI NG STARTED

4.1 Cleaning and Sterilizing

1. For the first time and after each use, you must disassemble, wash and sterilize all the breast pump parts that come into contact with breast milk.
2. Disassemble and clean the parts that come into contact with breasts and breast milk immediately after use , as bacteria can grow quickly in breast milk residue.
3. Take care when cleaning the silicone flange, diaphragm and valve, if it gets damaged, your breast pump will not function properly.
4. Never wash or sterilize the pump motor, this component does not come into contact with your breast milk. You can wipe this part clean with a soft cloth.

• The pump motor contains electronics that should be kept dry. A clean, damp cloth can be used to clean the pump motor. Any other cleaning method will be classed as misuse under the warranty.

Washable parts:
milk bottle, flange, diaphragm, linker, valve, bottle lid, flange insert.

• Cleaning washable components that come into contact with milk prevents the build-up of dry milk residue, which can prevent the growth of bacteria.

Warnings:

• Missing of the Seal Ring will cause vacuum leak.
• Do not get the pump motor wet during washing and sterilizing.

The pump body which houses the electrical components should be wiped down with a low-level disinfectant such as ethyl alcohol or isopropyl alcohol (70 – 90 %).

Clean washable components| | Sterilize washable components

---|---|---
1. Rinse in cold, clear water ( approx +20°C / +68°F ).
2. Wash in warm water than five minutes (approx +30°C / +86°F) using mild dish washing soap and wipe  afterwards with a clean cloth.
3. Rinse in cold, clear water ( approx +20°C / +68°F ) for 10 to 15 seconds.| Rinse in boiling water for no more
OR
Suitable for steam or cold water sterilizing methods.
We do not recommend steam sterilizing for more than five minutes*.

• For additional cleaning guidelines see the Center for Disease Control website
  https://Avwww.cde.gow/healthywater/hygiene/healthychildcare/infantfeeding/breastpump.html
  4.2 Charging

  1. When the battery is low in working process, the leftmost indicator light will flash.
  2. When charging, the indicator light will light up and the pump will not turn on. Use the charging cable provided to connect the pump motor to a USB power source (5V 2A), such as your phone plug.
  3. When fully charged, the five indicator lights all light up. It takes approximately two hours to fully charge the battery, which provides approximately two hours’ usage time at standard settings.

Please only use the charging cable provided with Parru breast pump. Do not use Parru breast pump while charging.
Tips: Charge immediately after finishing your pumping session if a low battery is indicated.
Before each use, you may check how much battery power is left in the standby mode when pressing the -+” and ‘ -” buttons at the same time for 2 seconds to count how many indicator light is on in standby mode. Each indicator light represents around 20% of the remaining power.
4.3 Flange Size
Parru breast pump comes with preassembled 25mm flange and two flange inserts in size of 21mm and 17mm, so you can find a flange size fit that is comfortable for you.
4.4 Assembling the Pump

1. Make sure all parts are dry before putting them together (after the parts have been cleaned and sterilized). Attach the Diaphragm (03) to the linker (02).
2. Attach the o-ring (06) to the linker (02). Do not twist the o-ring.
3. Attach the Valve (07) to the linker (02).
4. Push the well-assembled linker (02) into the Pump Motor (04). Make sure it’s assembled in place and the diaphragm is pressed tightly.
5. Twist the milk bottle (05) onto the Pump motor (04). Follow the instructions below to fasten the milk bottle.
6. Push the flange (01) into the pump motor (04), make sure it’s aligned and assembled in place.
7. In case that the standard 25mm silicone flange (01) are too big for you, you may choose the 21mm (08) or 17mm (09) flange inserts, to be placed in the center of pump motor (04).

USING Parru BREAST PUMP

Caution: Wash hands with soap and water, and inspect and assemble clean pump kit. 5.1 Aligning Your Nipple
Correct nipple alignment in the flange is key to comfort, expression and performance. Your nipple must be positioned correctly in the flange tunnel before pumping to avoid discomfort. 5.2 Finding The Right Compression

1. Parru breast pump is designed to be worn with your standard nursing bra and you can use it in either a sitting or standing position.
2. Getting the right compression could impact milk volumes. The breast pump needs to be firmly pressed against your breast, there should be no gaps between the breast pump and your breast.
3. Every bra has a different level of support, so make sure to get the compression right before each session. If you are using a particularly structured and inflexible bra, the included bra adjuster may be used to create more room.
4. Once the buckle of each end is hung on the nursing bra, you can adjust the length of bra adjuster to make it more comfortable.
   

5.3 Starting Your Session
Long press the power button to turn on the breast pump and position it in your bra.
Short press the power button to Play / Pause. (when the pause time exceeds 5 minutes, the pump will automatically shut down and enter the standby mode).

1. Modes
   Long press the power button to switch the pump on, it automatically enters into stimulation mode at Level 1 (default setting) with the leftmost indicator lighting up. This is a faster pumping rhythm to stimulate milk let-down.
   The breast pump will automatically switch to Expression mode after 2 minutes. You can also press mode button to enter expression mode if your milk starts to flow earlier. This is a slower pumping rhythm for efficient milk expression.

2. Intensity Settings
   1. Parru wearable breast pump has 5 intensity (vacuum) settings, giving you control over what feels comfortable and works most efficiently in both Stimulation and Expression modes. 2. Once you can feel the suction on your nipple, use “+” “-” to adjust intensity to find your preferred setting in both modes. The 5 indicator lights represent 5 levels.
   Tips: a higher intensity setting does not always mean a higher volume of milk. Putting your nipple under excess stress can reduce milk production. Always ensure you are pumping at a comfortable level. If you don’t feel suction, please check the pump is assembled correctly.

3. Ending Your Session
   1. Long press the Power button to stop pumping and switch off (The pump will automatically switch off after working for 30 minutes).
   2. Take off your bra, and slide a finger under the rim of the flange. This should break the seal between the flange and the breast tissue.
   3. Remove the breast pump.

5.4 Storing Your Milk
After finishing your pumping session, twist the milk bottle (05) to remove it from the Pump Motor (04), you may store your breast milk in the Bottle using the Lid (10) provided or pour your breast milk into a container for storage or feeding.
When storing milk, always follow the guidance of your lactation consultant or health professional.
Warnings:

• Clean all parts that come into contact with your breast and breast milk, and inspect for damage after each use.
• Do not store wet or damp components, as mold may grow.

TECHNICAL SPECIFICATION

Problem 1: Weak suction or no suction.

diaphragm.
The connection between diaphragm and pump motor is loose.| Tighten all connections.
| Choose the correct flange size based on your needs. keep the flange fit the breast all the time with the nipple in the center of the flange.

Problem 2: Can not turn on or charge.

The output does not meet the requirements. or the charger is plugged improperly.| Use the right charger and make sure it is plugged properly.
Run out of battery.| Charge the breast pump.

Problem 3: Milk backflow

pumping and switch off the pump, clean it. Please don’t use it until the diaphragm is well-fitted or replace a new diaphragm.

FCC Statement
Any Changes or modifications not expressly approved by the party responsible for ompliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>