BJE 008566 Red Fox Tank Gauge Instruction Manual
- June 11, 2024
- BJE
Table of Contents
008566 Red Fox Tank Gauge
Instruction Manual
008566 Red Fox Tank Gauge
MODEL 008566
Recommended Installation, Maintenance and Inspection Instructions
Important safety instructions – save these instructions in a readily
accessible location.
WARNING Never use with gasoline or highly flammable liquids.
WARNING: Cancer and Reproductive Harm – www.p65warnings.ca.gov
INSTALLATION INSTRUCTIONS
- Pull chain out of groove in swivel nut.
- Remove cap from swivel nut and pull chain through cap to free chain.
- Remove tissue paper allowing chain to free-fall. Hold gauge chain firmly. Do not let go of gauge chain: It will retract into body and be irretrievable.
- Confirm gauge chain is knot-free.
- Attach float eyelet to end of chain.
- Slowly pull float down then retract gauge chain to confirm gauge is functioning properly.
- Apply Teflon tape or appropriate pipe thread sealant to male threads of gauge. Ensure there is no sealant on the chain or internal mechanism, as this may void the warranty.
- Using the chain, slowly lower the float assembly to the bottom of the tank (do not drop float in).
- Install gauge to tank, tighten firmly – approximately 1 to 2 turns past hand tight – but do not overtighten.
DO NOT OVERTIGHTEN. DO NOT USE HOUSING AS A WRENCH.
ALWAYS USE CHAIN TO LOWER FLOAT TO BOTTOM OF TANK.
TESTING/MAINTENANCE/INSPECTION
Quarterly
- Remove gauge from tank and confirm smooth movement of chain.
- Apply city, state, or federal testing regulations as appropriate.
MADE IN THE USA
ALWAYS ADHERE TO INSTALLATION / USAGE INSTRUCTIONS AND WARNINGS.
Improper use may result in injury, damage, or hazardous spill.
GENERAL WARNINGS / INSTRUCTIONSSHOCK OR INJURY TO PERSONS:
- Use of equipment is at individuals’ own risk.
- Always abide and adhere to city, state, and federal regulations regarding use and installation of monitoring equipment.
- Always follow the product manufacturer’s installation and maintenance instructions. •
- Always turn off all power to monitor during maintenance activities.
- Always replace or remove from service damaged equipment immediately.
- Always report leaks / spills / accidents to appropriate authorities.
- Always wear appropriate safety equipment during maintenance and inspection activities.
- Always have appropriate fire extinguishing equipment within 5 ft/ 1.5 m of tanks.
- Always use Teflon ® tape or appropriate thread sealant.
- The tank contents are the sole responsibility of the tank owner.
- Never allow waste product to touch eyes or skin.
- Never install monitors outdoors without proper protection from the elements.
- Never use on below ground storage tanks.
- Never exceed the maximum milliamps specified in manufacturer’s installation and maintenance instructions.
- Never solely rely on this product; there is no substitute for human supervision.
- Never to be used as a component of any automatically controlled pump transfer system.
CAUTION: NEVER USE HOUSING AS A WRENCH!
Important safety instructions – save these instructions in a readily
accessible location.
WARRANTY
Husky Corporation will, at its option, repair, replace, or credit the purchase
price of any BJE® product deemed to be defective in material and/or
workmanship for a period of one (1) year.
Buyer must return the products to Husky® , transportation charges prepaid. The
warranty excludes damages due to malfunction, failure to follow manufacturer’s
installation, operation or maintenance instructions and guidelines,
unauthorized modifications or alterations, abuse, or misuse.
The warranty provisions contained herein apply only to original purchasers who
use the equipment for commercial or industrial purposes. There are not other
warranties of merchantability, fitness for a particular purpose, or otherwise,
and any other such warranties are hereby specifically disclaimed.
Husky assumes no liability for labor charges or other costs incurred by Buyer
incidental to the service, adjustment, repair, return, removal or replacement
of products. Husky is not responsible for any losses (including loss of
profits or revenues) incurred by the purchaser during the time necessary to
repair the equipment. Husky assumes no liability for any incidental,
consequential, or other damages under any warranty, express or implied, and
all such liability is hereby expressly excluded. Husky reserves the right to
change or improve the design of any Husky Oil Filter Crushers, Tank Monitors,
Tank Gauges, Overfill Alarms, Overfill Accessories, Air Shut-off Valves,
Solenoid Valves, and Electronic Drain Valves without assuming any obligations
to modify any Husky Oil Filter Crushers, Tank Monitors, Tank Gauges, Overfill
Alarms, Overfill Accessories, Air Shut-off Valves, Solenoid Valves, and
Electronic Drain Valves previously manufactured.
Husky Corporation
2325 Husky Way
Pacific, MO 63069
Phone: 800-325-3558
Fax: 636-825-7300
www.husky.com
Page 2 009344-5 7/2019
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>