BJE 010528 55 Gallon Horizontal Drum Gauge Instruction Manual

: May 15, 2024
: BJE

Table of Contents

BJE 010528 55 Gallon Horizontal Drum Gauge
Product Information
Product Usage Instructions
FAQs
Important Safety Instructions
INSTALLATION INSTRUCTIONS
TESTING /MAINTENANCE /INSPECTION
GENERAL WARNINGS
WARRANTY
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BJE 010528 55 Gallon Horizontal Drum Gauge

Product Information

Specifications:
- Model: #010528
- Product: Seasee 55 Gallon Horizontal Drum Gauge
- Installation: Horizontal gauge for 55-gallon drums
- Material: Made in the USA

Product Usage Instructions

Installation Instructions:
- Install faucet/tee subassembly into drum 3/4 NPT bung.
- Tighten approximately 1 or 2 turns past hand tight. Ensure the female quick disconnect is in the vertical position.
- Install quick disconnect sight glass tube sub-assembly onto the faucet/tee subassembly.
- If needed, loosen the 2 NPT bung cap to allow the drum to breathe.
- Place the drum in an appropriate cradle and check for leaks.
Removal Instructions:
- To remove the drum gauge, follow the installation steps in reverse order.
Testing/Maintenance/Inspection:
- If there is any test or inspection failure, immediate equipment replacement or removal from service is required.
- Always adhere to maintenance schedules and safety checks.

FAQs

Q: Can this drum gauge be used with gasoline or highly flammable liquids?
- A: No, it is recommended to never use this drum gauge with gasoline or highly flammable liquids to prevent hazards.
Q: What should I do if I encounter a leak during installation?
- A: If you notice a leak during installation, stop using the drum gauge immediately, and address the issue before continuing use to prevent any accidents.

Important Safety Instructions

Important safety instructions – save these instructions in a readily accessible location.

WARNING: Cancer and Reproductive Harm – www.p65warnings.ca.gov.
WARNING Never use with gasoline or highly flammable liquids.

INSTALLATION INSTRUCTIONS

55-gallon drum quick disconnect horizontal gauge

Use pipe thread sealant (not Teflon® tape) approved for automotive fluids on male threads of faucet/tee subassembly.
Install faucet/tee subassembly into drum 3/4″ NPT bung.
Tighten approximately 1 or 2 turns past hand tight.
- Note: the female quick disconnect must be in the vertical position – do not over-tighten. $BJE-010528-55-Gallon-Horizontal-Drum-Gauge-FIG-1 $1$$
Install quick disconnect sight glass tube sub-assembly onto faucet/tee sub-assembly.
If necessary, loosen the 2″ NPT bung cap to allow the drum to breathe. $BJE-010528-55-Gallon-Horizontal-Drum-Gauge-FIG-1 $2$$
Place the drum in the appropriate cradle and check for leaks.
To remove the 55-gallon drum quickly disconnect the horizontal gauge, and follow steps 1 thru 6 in reverse order.

TESTING /MAINTENANCE /INSPECTION

Monthly
- Check for leaks.
- Follow all city, state, or federal wiring code requirements as appropriate.
- Apply city, state, or federal testing regulations as appropriate.
- ANY TEST / INSPECTION FAILURE REQUIRES IMMEDIATE EQUIPMENT REPLACEMENT OR REMOVAL FROM SERVICE.

ALWAYS ADHERE TO INSTALLATION / USAGE INSTRUCTIONS AND WARNINGS. Improper use may result in injury, damage, or hazardous spill.

GENERAL WARNINGS

GENERAL WARNINGS / INSTRUCTIONS ABOUT A RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS:

Use of equipment is at the individual’s own risk.
Always abide by and adhere to city, state, and federal regulations regarding the use and installation of monitoring equipment.
Always follow the product manufacturer’s installation and maintenance instructions.
Always replace or remove from service damaged equipment immediately.
Always report leaks /spills /accidents to appropriate authorities.
Always wear appropriate safety equipment during maintenance and inspection activities.
The drum contents are the sole responsibility of the drum owner.
Never allow waste products to touch the eyes or skin.

WARRANTY

Husky Corporation will, at its option, repair, replace, or credit the purchase price of any BJE® product deemed to be defective in material and/or workmanship for one (1) year.
Buyer must return the products to Husky®, transportation charges prepaid.
The warranty excludes damages due to malfunction, failure to follow the manufacturer’s installation, operation or maintenance instructions and guidelines, unauthorized modifications or alterations, abuse, or misuse.
The warranty provisions contained herein apply only to original purchasers who use the equipment for commercial or industrial purposes.
There are no other warranties of merchantability, fitness for a particular purpose, or otherwise, and any other such warranties are hereby specifically disclaimed.
Husky assumes no liability for labour charges or other costs incurred by Buyer incidental to the service, adjustment, repair, return, removal or replacement of products.
Husky is not responsible for any losses (including loss of profits or revenues) incurred by the purchaser during the time necessary to repair the equipment. Husky assumes no liability for any incidental, consequential, or other damages under any warranty, express or implied, and all such liability is hereby expressly excluded.
Husky reserves the right to change or improve the design of any Husky Oil Filter Crushers, Tank Monitors, Tank Gauges, Overfill Alarms, Overfill Accessories, Air Shut-off Valves, Solenoid Valves, and Electronic Drain Valves without assuming any obligations to modify any Husky Oil Filter Crushers, Tank Monitors, Tank Gauges, Overfill Alarms, Overfill Accessories, Air Shut-off Valves, Solenoid Valves, and Electronic Drain Valves previously manufactured.