CORRO-PROTEC ANTI-CORROSION Anode Rod for Water Heaters User Guide
- June 11, 2024
- CORRO-PROTEC
Table of Contents
CORRO-PROTEC ANTI-CORROSION Anode Rod for Water Heaters User Guide
FOR YOUR RECORDS
Anode Rod Serial Number :————————–
Serial number can be found on the top of the anode rod stainless steel part.
Water Heater Serial Number :————————
READ THIS MANUAL
Inside you’ll find many helpful hints on how to install and maintain your Corro-Protec anode rod.
You’ll find several answers to common questions in the FAQ section at the end of this document.
If you have general questions about the Corro-Protec anode, you can visit our website www.corroprotec.com/faq or contact us at info@corroprotec.com
READ THE SAFETY INFORMATION
Your safety and the safety of others are very important. There are many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol. Recognize this symbol as an indication of Important Safety Information! This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word
“DANGER”, “WARNING”, “CAUTION” or “NOTICE”
These words mean:
DANGER An imminently hazardous situation that will result in death or serious injury.
WARNING A potentially hazardous situation that could result in death or serious injury and/or damage to property.
CAUTION A potentially hazardous situation that may result in minor or moderate injury
NOTICE Attention is called to observe a specified procedure or maintain a specific condition.
IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
Be sure to read and understand the entire Use and Care Manual before attempting to install or operate this powered anode rod. It may save you time and cost. Pay particular attention to the Safety Instructions. Failure to follow these warnings could result in serious bodily injury or death. Should you have problems understanding the instructions in this manual, or have any questions, STOP, and get help from a qualified service technician, or the local electric utility.
SAFETY PRECAUTIONS
- Read this manual entirely before installing or operating the water heater.
- Use this appliance only for its intended purpose as described in this Use and Care Manual.
- Be sure your appliance is properly installed in accordance with local codes and the provided installation instructions.
- DO NOT attempt to repair or replace any part of your powered anode rod unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.
TOOLS REQUIRED
-
Teflon tape
-
Universal pliers
-
Ratchet wrench with a 1 1/16” socket
-
Ratchet wrench with a 31mm socket
(you can also use an adjustable wrench or a 1 3/16 socket) -
Robertson screw driver
(squared-headed)
INSTALLATION STEPS
The Corro-Protec anode is universal and can be installed on all tanks and
adapts to all types of water.
If you DIDN’T ORDER THE RIGHT MODEL for your tank, write to us at
info@corroprotec.com with
the following information and we will take care of the exchange process, FREE
OF CHARGE. Your
name, address, phone, Corro-Protec model ordered and Corro-Protec model you
need.
NEED ASSISTANCE?
Email us : info@corroprotec.com Call us or text
us : 1-877-466-6660
-
Disconnect the water heater from the power source.
Gas: Twist the dial on the top of the thermostat from the ON to the OFF position. Electric: Switch the circuit breaker for the water heater to the OFF position.
CAUTION ELECTRICITY / GAS -
Turn off water supply
-
Locate a 110 volts power outlet.
The Corro-Protec rectifier cord length is 12 feet long. This should be enough to
reach an outlet. If it’s not the case, install a 110v outlet near the tank by a professional electrician following the electric code.
-
Release the pressure from the tank using the pressure relief valve. Make sure the pressure relief valve is safely connected to a drain. When the tank don’t have pressure anymore, turn off the pressure relief valve.
CAUTION HOT WATER
-
Locate the magnesium anode rod on top of the tank.
You can use the owner’s manual of the water heater to help you locate the anode. Here are some standard locations of the anode rod in your tank:
If you have a Bradford White water heater, the anode rod might be located in the hot water outlet. Please see page 10 for more informations.
-
Using the ratchet wrench fitted with a 1 1/16’’ socket, unscrew the existing anode counterclockwise
NOTICE Use a 1 1/16’’ hexagonal socket to avoid damaging the rod hex head.
If you are having some difficulties removing the anode rod, here’s some tips: -
Use a breaker bar
-
Use an impact wrench
-
Use a torque multiplier
If you are not able to remove the magnesium rod after trying all steps listed above, send us an email at info@corroprotec.com and we will send you fittings to install the Corro Protec anode it in the hot water outlet port. -
Slowly remove the original magnesium anode.
Should you have to cut it into pieces due to limited space, be sure to hold the bottom to keep it from slipping inside the tank.
CAUTION PLEASE DISPOSE IN A SAFE WAY and as per your municipality environmental waste regulations. -
Cover the threaded part of the anode with Teflon Tape.
Apply 5-6 layers of teflon tape counterclockwise .
-
Insert the Corro-Protec anode and manually screw it to make sure threads are aligned.
-
**Using the ratchet wrench fitted with a 31 mm socket, screw the Corro-Protec anode rod clockwise.
NOTICE DO NOT USE EXCESSIVE FORCE WHEN TIGHTENING.
**
-
Install the black grounding connection on one of the tank cover screws. Make sure the ground is in direct contact with the metal and not on the paint.
-
Insert the female connection in the exceeding end-piece of the anode and press firmly using universal pliers.
-
**Turn on water supply and make sure the tank is full.
**
-
Connect the power source.
Gas: Twist the dial on the top of the thermostat from the OFF to the ON position. Electric: Switch the circuit breaker for the water heater to the ON position. -
Connect the Corro-Protec power supply to the 110v outlet.
The light located on the rectifier will automatically light after couple seconds.
If the Green light doesn’t turn ON:
To ensure that the Corro-Protec works, the following conditions must be met:
* The rectifier must be connected.
* Corro-Protec must be connected to the rectifier.
* The negative side must be installed on the water heater, as indicated in the instruction manual.
* The water heater must be functional (filled and operational). If the above conditions are met and the indicator light is not lit, please visit corroprotec.com/warranty-claim
- Register your Corro-Protec anode to activate the 20 years warranty at corroprotec.com/warranty
MAINTENANCE
Corro-Protec recommends inspecting your anode yearly to make sure the green
light is on.
Green light on the power supply means everything is working as it should and
your tank is protected.
FAQ Frequently asked questions
How do you install the Corro-Protec on a Bradford White Water Heater?
Since Bradford White water heaters have the magnesium anode built into the hot
water outlet, you need our Corro-Protec for Bradford Whites model that comes
with all the fittings you need to install it.
If you ordered the regular Corro-Protec instead of the Badford White model, you don’t have to create a return or pay any return fees. You just have to send us an email at info@corroprotec.com with your Name, Address and phone number so we can take care of the exchange for you.
My water heater has 2 magnesium anodes, should I replace both?
The answer is no and that is why Corro-Protec offers different models adapted
to tank sizes.
If your water heater has two anodes, you can replace one of them with our Corro Protec anode and leave the other one in place. Even if you install the Corro-Protec anode to eliminate the rotten egg smell in your hot water, you don’t need to remove the second magnesium anode.
Do I have to unplug the Corro-Protec if we turn off the hot water for
several
months at our cottage?
The Corro-Protec does not require any special maintenance. Leave it connected
at all times, and it will work only if necessary. Even if you turn off the hot
water tank, if there is still water in the tank, the Corro-Protec will remain
functional to prevent corrosion. If you empty the tank, the Corro-Protec will
turn off automatically because the water acts as a conductor between the anode
and the ground.
An impressed current anode does not function as a heating element. There is no danger in emptying the water from the tank without disconnecting the anode
Can I use a powered anode if I have a water softener?
Yes, it is even highly recommended to install an impressed current anode if
you have a water softener.
The water softener generally makes the water more aggressive to the tanks, which reduces the life of your hot water tank and creates a more conducive environment for the development of Sulfur Reducing Bacteria that creates the rotten egg smell in hot water. The Corro-Protec Powered anode rod will automatically adjust to provide optimum rust protection.
What is the annual power consumption of a Powered Anode Rod?
Since the amount of current used by the anode will vary from region to region
due to the hardness of the water, it is impossible to give an exact answer.
However, on average, the anode will use 10 KWh per year. If we take the
average price of electricity in the United States, the cost to run the anode
24 hours a day all year round is $ 1.36.
Is it normal to read a voltage lower than that indicated on the Powered
Anode rectifier?
Yes, because the voltage adjusts automatically depending on the resistance of
your water. A very low voltage means that your water is very conductive and
the anode does not need to send much current to provide adequate protection.
LIMITED WARRANTY
What does this limited warranty cover?
Corro-Protec warrants this powered anode system against defects in material or workmanship for twenty years when installed in a single-family residence. If this part is installed in any location other than a singlefamily residence, the warranty period is reduced to 2 years. This warranty sets forth owner’s only remedy and our sole responsibility with respect to any defect in this part.
During the warranty period, Corro-Protec will repair or replace, at no charge, products or parts of a product that proves defective because of improper material or workmanship, under normal use and maintenance.
What will we do to correct problems?
Corro-Protec will either replace or repair the product at no charge, using new or refurbished replacement parts. If an identical part is no longer available due to a change in law, regulation, or standard, we will replace the part with one having similar functionality.
How long does the coverage last?
The limited warranty periods for physical goods purchased from Corro-Protec is
20 years from the date of purchase when installed in a single-family
residence. A replacement physical good or part assumes the remaining warranty
of the original physical good or 90 days from the date of the replacement or
repair, whichever is longer.
What does the limited warranty not cover?
This limited warranty does not cover any problems that is caused by :
- Conditions, malfunctions, or damage not resulting from defects in material or workmanship.
- Improper installation or maintenance.
- Failure to follow applicable codes and/or printed instructions.
- Alterations to the anode or the power supply.
- Failure to operate the part at the specific voltage/wattage.
- Damage during shipping, transport, or installation.
- Abuse, misuse, accident, fire, flood, or acts of God.
- Service trips to teach you how to install, use or maintain the part.
- The water heater itself or any of its components which are not part of the Corro-Protec product.
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE APPLICABLE DURATION OF THIS WARRANTY. ALL OTHER WARRANTIES ARE EXPRESSLY DISCLAIMED. IN NO EVENT SHALL WE BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, SPECIAL, PUNITIVE OR OTHER DAMAGES, WHETHER LIABILITY IS BASED ON TORT, CONTRACT, STRICT LIABILITY OR ANY OTHER THEORY. Some states or provinces do not allow limitation and/or the above exclusion on how long implied warranties last, or do not allow for the exclusion of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary upon location.
CORRO-PROTEC
40, Boulevard Industriel, Princeville, Quebec, G6L 4P2
1-877-466-6660 |
info@corroprotec.com
CORROPROTEC.COM
References
- Corro-Protec - Powered anode rod - Residential, RV & Commercial
- Corro-Protec Warranty & Returns - Corro-Protec
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>