TURTLE BEACH Velocityone Universal Rudder Pedal Controls User Guide

TURTLE BEACH Velocityone Universal Rudder Pedal Controls

Product Information

The Rudder Pedals come with the following:

• 3 2M standalone connection cable
• USB-C DE 2M
• 4 2.5M pass-through cable
• DE 2.5M
• 5 spring sets x2 (60N & 80N)
• 6 Allen key tool
• 8 cockpit fixing screws x4
• USB-C socket prise USB-C

The Rudder Pedals also come with two different sets of pedals: one for steep pedal setups (as found in smaller, private airplanes)  and one for flat pedals (as in large, commercial plane types). The setup can change anytime depending on the plane you want to simulate. Additionally, there are two different sets of springs to control the resistance of the pedal operation. There are also two sets of rubber pads to ensure a secure grip on different surfaces: one set for flat surfaces and spiked for use on carpets and similar surfaces. The pedal width can change to further simulate the craft you are flying. There are six positions to choose from.

Product Usage Instructions

Hardware Setup

1. Attach the appropriate set of pedals to the Rudder Pedals based on the plane you want to simulate.
2. To change the resistance of the pedal operation, use the Allen key provided to remove the screw cap, then pull the spring out. Insert the new spring and close the chamber by tightening the screw cap. Repeat the process for the other side with the matching spring.
3. Attach the appropriate set of rubber pads to the recessed areas on the bottom of the product based on the surface you will be using the pedals on.
4. Adjust the pedal width to further simulate the craft you are flying. There are six positions to choose from.
5. Connect the Rudder Pedals to your computer using either the 3 2M standalone connection cable or the USB-C DE 2M cable.
6. If using the 4 2.5M pass-through cable, connect it to your joystick or throttle controller, then connect the Rudder Pedals to the pass-through cable.
7. Use the cockpit fixing screws to securely fix the Rudder Pedals in place.

IMPORTANT : READ BEFORE USING ANY QUESTIONS? TURTLEBEACH.COM/SUPPORT

CONTENTS

CONTROLS

HARDWARE SETUP

Your Rudder Pedals come with two different sets of pedals, one for steep pedal setups (as found in smaller, private airplanes) and one for flat pedals (as in large, commercial plane types). This setup can change anytime depending on the plane you want to simulate. Your Rudder Pedals come with two different sets of springs to control the resistance of the pedal operation.

1. Using the Allen key provided, remove the screw cap, then pull the spring out.
2. Insert the new spring and close the chamber by tightening the screw cap.
3. Repeat the process for the other side with the matching spring.

Your Rudder Pedals come with two sets of rubber pads to ensure a secure grip on different surfaces: One set for flat surfaces and spiked for use on carpets and similar surfaces. To attach the pads, remove the protective film on the back and attach them to the recessed areas on the bottom of the product.

The pedal width can change to further simulate the craft you are flying. There are six positions to choose from.

To adjust the width, push the Lock Handle on one side, move the pedal base to the desired position and release the handle again. Make sure that both pedals are set to the same width.

CONNECTING TO PC

The Rudder Pedals are set to work in PC Mode by default. Use the supplied 2m USB-A to USB-C to connect the product to your Windows PC. Windows will recognize the device automatically, and the product LED will shine white. The pedal axes will now be assignable in your simulation software of choice.

PASS THROUGH CONNECTION FOR XBOX

Use the Pass-Through cable to achieve Xbox compatibility via the VelocityOne Flight system.

1. Start with the VelocityOne Flight* connected to an Xbox console and set to Xbox Input Mode.
2. Remove the existing USB-C to USB-C cable from the Yoke and throttle quadrant.
3. Connect the pass-through cable to match the corresponding port colours as shown.
4. Push and hold the Mode button on the pedals for three seconds, then release. The status LED will turn blue.
5. On the VelocityOne Flight FMD, navigate to the Accessories menu and enable the Rudder Pedals.

VelocityOne Flight must be running the latest firmware to enable compatibility.

FIXED INSTALLATION

The Rudder Pedals can be fixed to existing cockpit setups using the supplied screws. To prevent material wear and potential damage to the product, do not over tighten the screws.

Note : When installing the Pedals, make sure they are fixed to a sturdy, even surface.

CALIBRATION

The Rudder axis is calibrated at factory to the widest pedal width. When you first power up the pedals and move the rudder axis to min and max deflection, it will self-calibrate to the width you have set. If you change the width of the pedals, we recommend power cycling the product. You can then move the rudder axis through full deflection again and the new calibration data will be set

SAFETY INFORMATION

Do not use excessive force on the pedals. To prevent damage, do not stand on the pedals.

• Do not overtighten screws when changing the springs or pedals to prevent material damage.
• This product uses strong springs. Use caution when adjusting to avoid possible injury when operating the mechanisms.

Download Turtle Beach Control Center for feature and performance updates on Windows and Xbox

Not seeing what you’re looking for here?
Visit turtlebeach.com/support for the latest Tech Support information.

Regulatory Compliance

Statements for the VELOCITYONE RUDDER Federal Communications Commission (FCC) Compliance Notices Class B Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15, Subpart B of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product is compliant with the Consumer Product Safety Improvement Act of 2008, Public Law 110-314 (CPSIA)

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.

Canadian ICES Statements
Canadian Department of Communications Radio Interference Regulations This digital apparatus does not exceed the Class B limits for radio-noise emissions from a digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. This Class B digital apparatus complies with Canadian ICES-003.

European Union and European Fair Trade Association (EFTA) Regulatory Compliance Declaration of Conformity indicates compliance with the Essential Requirements of the EMC Directive of the European Union (2014/30/EU). This equipment meets the following conformance standards

Applicable Standards:

• EMC : EN55014-1 / EMI: EN55014-2
• CE-GPSD : EN62368-1
• CE Packaging : 94/62/EC Toxic Elements in Packaging
• Additional licenses issued for specific countries available on request.

Other:
EN71-1/-2/-3, Chemistry : BPA

Environmental:
REACH: SVHC 211, REACH: Appendix 17: Entry 23 of REACH Annex XVII / PAHs: Entry 50 of REACH ANNEX XVII, ROHS 2.0 WEEE : Directive 2012/19/EU

Please visit the following URL for a complete copy of the Declaration of Conformity: http://www.turtlebeach.com/homologation This symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for  recycling, please contact your local authority, or where you purchased your product. Voyetra Turtle Beach Inc. is obligated as a producer with a main activity of selling under The Producer Responsibility Obligations (Packaging Waste) Regulations 2007. To fulfil our obligation we are registered with Comply Direct and their Recycling Room. Here you will find advice and information on packaging waste management, recycling symbols and the waste hierarchy principles of reduce, reuse and recycle. https://www.complydirect.com/the-recycling-room/ WWW.TURTLEBEACH.COM

References

• Turtle Beach Support
• P65Warnings.ca.gov
• Turtle Beach® #1 Gaming Headsets - Hear Everything. Defeat Everyone.
• Turtle Beach Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>