BeaverLAB DDL-G1A-B Electric Glue Gun Instructions
- June 11, 2024
- BeaverLAB
Table of Contents
BeaverLAB DDL-G1A-B Electric Glue Gun Instructions
Product Introduction
Please read this manual carefully before using the product and keep it
properly.
- Protective cap of glue gun
- Glue gun nozzle
- Switch key
- Status indicator
- Rubber inle
- Glue trigger
- Lanyard
- Type-C power supply port
Instructions
This product is suitable for 7mm hot-melt adhesive stick, please do not insert
hot-melt adhesive stick of other specifications.
Cordedversion： Be sure to select appropriate power supply (power supply
voltage DC5V, power supply current ≥ 2A)
(Mobile phone charger and charging treasure can be used). Connect the glue gun
to the power supply equipment with the power supply cable
Battery version： Please ensure that the equipment has sufficient power
ON-OFF
- In the shutdown state, press and hold the switch button for 2S to start the product.
- When the machine is turned on, long press the switch button for 2s to turn off the product.
- If the product is not used for any operation within 3 minutes, the product will automatically shut down
Usage method
- Insert the glue stick, after starting the product, wait for the green light of the indicator to be on (the waiting time is about 30 s), after the pre heating is completed, press the trigger to release the glue.
- Apply the hot melt adhesive to the object to be bonded, press it for aperiod of time, and the bonding is completed after the hot melt adhesive has solidified.
※ Charging (applicable to lithium battery version)
- You can use the mobile phone charger, power bank, computer USB interface and other power supplies that can output 5V DC voltage to charge this product.
- If the product has not been used for a long time, please fully charge the product before use.
Indicator Status
| Indicator Status | Indicator Status | Product status |
|---|---|---|
| Green Fashing | Heating | |
| Green Bright | Can Work | |
| Flash Red Light | Low Battery（Battery version） | |
| Red Slow Flashing | Charging（Battery version） | |
| The red light stays on for3 minutesand then goes out | Charging |
completed（Battery version）
Tips
- Be sure to take off the protective cap of the glue gun before use.
- The nozzle temperature of the glue gun is high during operation, please do not touch.
- The temperature of hot melt adhesive in molten state is very high, please do not touch.
- If the melted hot melt adhesive drops on the skin, please wipe it off immediately and wash it with cold water immediately.
Attention
- Lithium battery version products are not fully charged when leaving the factory, and should be fully charged before the first use.
- Lithium battery version products do not support charging while using.
- When inserting the glue stick for the first time/replacing the glue stick, please insert the glue stick forcefully, and release when the motor is tightly held for conveying.
- Do not forcibly pull out the glue stick before it is used up to avoid damaging the productt
- The lithium battery version has not been used for a long time. If the status indicator does not display normally during recharging, please keep charging for 30 minutes before observing.
- Wired version, plug and play.
- If not in use, please stand or hang the product.
- This product is only applicable to the glue stick with a diameter of 7mm
General faults and troubleshooting
Maintenance
- It is prohibited to place the product in a high temperature environment for a long time. If the product is not used for a long time, please place the product in a normal temperature and humidity environment, and charge the product once every six months.
- Please do not smash this product to avoid damaging the internal components.
Troubleshooting
| Fault | Reason | Exclusion method |
|---|---|---|
| Product does not work | Charge out | Use after charging |
| Automatic shutdown | Restart the product | |
| Internal circuit damage | Need repair | |
| Glue stick cannot be squeezed out | Glue stick is used up | Insert new glue |
stick
Internal blockage| Need repair
Unable to charge| Internal circuit damage| Need repair
BeaverLAB electric glue gun performance fault table
| Name | Fault content |
|---|---|
| BeavegrlLuAeBguelnectric |
- Unable to charge normally（Battery version）.
- The indicator cannot be displayed normally.
- The key cannot be used normally.
- he shell of the body is damaged due to structural or material factorswithout human reason.
BeaverLAB Electric Glue Gun
Battery version:
Product Model： DDL-G1B
Battery Capacity： 2000mAh
Charging Voltage: 5V 1A
Glue Stick Length： 125mm
Rated Voltage： DC 5V
Preheating Time： About 45s
Glue Stick Diameter： 7mm
Charging time： 3-4 h
Executive Standards： GB 4706.1-2005
Official Website: www.dangdangli.com
Manufacturer: Beaver Technology (Shenzhen) Co.Ltd
Address: F518 Fashion Creative Park,Xixiang Street,Baoan District
Shenzhen
E-mail: service@dangdangli.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>