HINKLEY 2205DZ LED Wall Mount Cape Cod Instruction Manual
- June 11, 2024
- HINKLEY
Table of Contents
HINKLEY 2205DZ LED Wall Mount Cape Cod
Product Information
HINKLEY Fixture
HINKLEY Fixture is a lighting fixture that comes in three different models – 2204, 2205, and 2206. The fixture is designed for indoor use only and needs to be mounted on a junction box on the wall. The fixture is packaged with glass and all the required mounting hardware except for two screws to attach the mounting strap to the junction box.
Product Usage Instructions
HINKLEY Fixture
- Find a clear area to work and unpack the fixture and glass from the carton.
- Review the instructions carefully before proceeding with the assembly.
- Prepare the mounting strap by threading one nipple into the center hole of the mounting strap, approximately 1/4 inch. (Refer Drawing 1)
- Attach the mounting strap to the junction box using two screws (not provided).
- To assemble the fixture, remove ball knob (3), lockwasher (4), and screw (5) from scroll (2).
- Slip the looped end of scroll (2) through loop (1) found on top of the canopy assembly.
- Line up the hole in the end of scroll (2) with the hole in the top of the backplate (B) of the canopy assembly.
- Slip lockwasher (4) onto screw (5) and slip screw up through hole in top backplate.
- Thread on ball knob (3) to secure scroll (2) to the fixture.
- Make electrical connections from supply wire to fixture lead wires. Refer to instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to continue installation of this fixture.
- Read wiring and grounding instructions (I.S. 18) and any additional directions before starting the installation.
- Turn off the power supply during installation.
- If new wiring is required, consult a qualified electrician or local authorities for code requirements.
- Connect the positive supply wire to positive fixture lead with an appropriately sized twist-on connector.
- Connect the negative supply wire to negative fixture lead.
Assembly Instructions
- Find a clear area in which you can work.
- Unpack fixture and glass from carton.
- Carefully review instructions prior to assembly.
- The construction of this fixture will be accomplished by first installing the mounting hardware to the junction box, assembling the fixture, making all necessary electrical connections, and then attaching the fixture to the wall.
- Prepare mounting strap (A) by threading 1” nipple (C) into the center hole of the mounting strap (A) , approximately 1/4“ – see Drawing 1.
- Attach mounting strap (A) to junction box (J) using two screws (B)not provided.
- To assembly fixture, first remove ball knob (3), lockwasher (4) and screw ( from scroll (2).
- Slip looped end (A) of scroll (2) through loop (1) found on top of ca assembly.
- Liine up hole in end of scroll (2) with hole in top of backplate (B) of ca assembly.
- Slip lockwasher (4) onto screw (5) and slip screw up through hole in top backplate.
- Threead on ball knob (3) to secure scroll (2) to fixture.
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
Make electrical connections from supply wire to fixture lead wires. Refer to instruction sheet(I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to continue installation of this fixture.
wiring grounding instructions
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
wiring instructions
Indoor Fixtures
- Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector – see Drawings 1 or 2.
- Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
- Please refer to the grounding instructions below to complete all electrical connections
Outdoor Fixtures
- Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector — see Drawings 2 or 3.
- Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
- Cover open end of connectors with silicone sealant to form a watertight seal.
- If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.
- Please refer to the grounding instructions below to complete all electrical connections.
grounding instructions
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) – see Drawing 1.
_ Note: _On straps for screw supported fixtures, first install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.
Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – see Drawing 3.
Caulking Instructions
After securing fixture to the wall it is recommended that the gap between the wall and the fixture backplate be sealed on the top and both sides, with a good quality waterproof caulk or silicone sealant (NOT INCLUDED) – see Drawing
After securing the fixture in place it is recommended that the gap between the mounting top and fixture base be sealed with any good quality waterproof caulk or silicone sealant (not included). It is also recommended that a small bead of caulk or sealant be put under the ball knobs used to mount fixture – see Drawing 2.
HINKLEY
- 33000 Pin Oak Parkway, Avon Lake, OH
- 44012 800.446.5539
- 440.653.5500
- hinkley.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>