Lucci 269800 Quill 2 Light Table Lamp Instruction Manual
- June 11, 2024
- Lucci
Table of Contents
Lucci 269800 Quill 2 Light Table Lamp
Product Information: QUILL 2 LIGHT TABLE LAMP
The QUILL 2 LIGHT TABLE LAMP is a portable luminaire that comes fully assembled and is ready to use for the first time. It is designed to be used with LED lamps only and has a maximum wattage rating of 10W (2x Max. 5W – LED lamps only). The lamp holder is G9 and the rated voltage is 220-240V~ 50Hz. The lamp weighs 2.4kg and has dimensions of H: 810mm L:910mm W: 200mm.
Product Usage Instructions:
-
Remove all packaging material from the portable luminaire and be careful not to throw away accessories that may be hidden within the packaging material. To help with assembly, lay the luminaire on its side on a smooth non-scratch surface.
-
Select a suitable location for your portable lamp.
-
Install the luminaire (D) on to the lamp base (I).
-
Install the included LED lamps (B) into the lamp holders.
Note: This luminaire must be used with LED lamps only. Do not exceed the maximum wattage rating. -
Install the shades (C & F) onto the lamp holders and ensure they are secure.
-
Adjust the luminaire arm (E) to your desired angle.
-
Insert the plug (H) into the mains power socket outlet and ensure it is fully plugged in.
-
Turn power on at the mains power socket outlet.
-
Use the cord line switch (G) to turn the lamp on/off.
Note: To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation, and use of the product. Please keep instructions for future reference.
Installation requirements
-
Select a suitable location for the portable luminaire:
- Ensure it is on a flat and stable surface.
- This portable luminaire is suitable for indoor use only.
- Do not place flammable material near or over the portable luminaire.
- Ensure the portable luminaire is not installed in the direct line of an air vent/system.
- If the portable luminaire is placed in an area prone to moisture, ensure that the area is well-ventilated, and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.
-
Do not exceed the maximum wattage rating. This luminaire must be used with LED lamps only.
-
Take care not to pull any electrical wires during unpacking as this may damage the connection.
-
Lay out all the components on a smooth surface and make sure no components are missing before assembling.
If parts are missing, return the complete product to the place of purchase for inspection or replacement. -
Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
-
Do not plug into the main’s power socket outlet before or during assembly. Only do so after the portable luminaire is fully assembled and is ready to use for the first time.
Installation directions
-
Remove all packaging material from the portable luminaire and be careful not to throw away accessories that may be hidden within the packaging material. To help with assembly, lay the luminaire on its side on a smooth nonscratch surface.
-
Select a suitable location for your portable lamp. See the requirements above.
-
Install the luminaire (D) on to the lamp base (I)
-
Install the included LED lamps (B) into the lamp holders.
NOTE: This luminaire must be used with LED lamps only. Do not exceed the maximum wattage rating. -
Install the shades (C & F) onto the lamp holders and ensure they are secure.
-
Adjust the luminaire arm (E) to you desired angle.
NOTE: Do not adjust the arm (E) more than 80°, as this may damage the joint or the internal wiring. -
Adjust the luminaire head (A) to you desired angle.
NOTE: Do not adjust the head (A) more than 86°, as this may damage the joint or the internal wiring. -
Insert the plug (H) into the mains power socket outlet and ensure it is fully plugged in.
-
Turn power on at the mains power socket outlet.
-
Use the cord line switch (G) to turn the lamp on/off.
NOTE: Do not adjust the arm (E) more than 80°, as this may damage the
joint or the internal wiring.
NOTE: Do not adjust the head (A) more than 86°, as this may damage the
joint or the internal wiring.
Safety tips
-
Always ensure the power is OFF and the portable luminaire has cooled down before performing any maintenance, cleaning or making any adjustment to the portable luminaire.
-
The external flexible cable or cord of the luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
-
To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
Young children should be supervised to ensure that they do not play with the portable luminaire. -
Handle the luminaire and shade with care to avoid any damage or breakage.
-
Select a suitable location away from liquids and hazards.
-
To clean, wipe with a soft damp cloth. Do NOT soak or immerse the product in water or other liquids.
-
Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
Specifications
Specifications|
---|---
SKU #| 269800
Rated Voltage| 220~240V~ 50Hz
Rated Wattage| 10W MAX (2x Max. 5W – LED lamps only)
Lamp Holder| G9
Weight*| 2.4kg
Dimensions| H: 810mm L:910mm W: 200mm
Warranty
- This portable luminaire is covered by 12 month warranty valid for in-store replacement or refunds only.
- The warranty period starts from the date of purchase. Please retain the proof of purchase.
- The warranty will be void if there is any damage due to improper usage or modification to the portable luminaire.
- Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>