PMXP2 Right Hand Hood Installation Guide
- June 11, 2024
- PMX
Table of Contents
PMXP2 Right Hand Hood
Product Information
The user manual provides instructions for installing the audio and antenna harnesses, reinstalling the right-hand hood panel, and installing the head unit. The audio harness is used to connect the PMX head unit to the vehicle’s speakers, subwoofer, and power source. The antenna harness is used to connect the vehicle’s antenna to the head unit.
Product Usage Instructions
Antenna Harness Routing
- Begin routing harness 2 towards firewall. Secure harness to electrical chassis harness with one cable tie 13 at taped location.
- Pass harness 2 through grommet in firewall.
- Route antenna harness 2 along accessory mounting panel. Secure in tabs along edge of panel.
Right-Hand Hood Reassembly
-
Reinstall right-hand hood panel with one hood fastener A and one push-pin rivet B. Do not torque hood fastener A at this time.
-
Reinstall right-hand hood panel with three hood fasteners A.
TORQUE
Hood Fasteners A: 89 in-lbs (10 N·m) -
Torque Hood Fasteners A
-
Reinstall hood nose panel with one fastener A.
TORQUE
Hood Fasteners A: 89 in-lbs (10 N·m)
Audio Harness Routing
Note : See Harness Detail section, page 3, for connector identification.
- Place audio harness q in accessory mounting panel.
- Route amplifier connector 1C and 1D through bottom opening of accessory mounting panel. Secure harness to accessory mounting panel with one routing edge clip 1Q. Join audio harness connectors 1C and 1D to amplifier.
- Route audio harness to driver side. Secure to front cab panel with four routing clips 1Q.
- Join audio harness connector 1H to tweeter and connector 1G to driver.
- Route audio harness to head unit. Secure rear audio connector 1J to accessory mounting panel with attached push-pin. Secure audio harness to accessory mounting panel with routing clip 1Q. Secure audio harness to chassis electrical harness with two cable ties f at taped locations 1R.
- Route audio harness to passenger side. Secure to front cab panel with four routing clips 1Q.
- Join audio harness connector 1E to tweeter and connector 1F to driver.
- Place audio harness 1 in accessory mounting panel
- Install fuse relay 1A onto accessory mounting panel. Join power connector 1B to Polaris Pulse® bar. Secure harness to accessory mounting panel with one routing edge clip 1Q.
- Route amplifier connector 1C and 1D through bottom opening of accessory mounting panel. Secure harness to accessory mounting panel with one routing edge clip 1Q. Join audio harness connectors 1C and 1D to amplifier
- Route audio harness to driver side. Secure to front cab panel with four routing clips 1Q.
- Join audio harness connector 1H to tweeter and connector 1G to driver.
- Route audio harness to head unit. Secure rear audio connector 1J to accessory mounting panel with attached push-pin. Secure audio harness to accessory mounting panel with routing clip 1Q. Secure audio harness to chassis electrical harness with two cable ties 13 at taped locations 1R.
- Route audio harness to passenger side. Secure to front cab panel with four routing clips 1Q.
- Join audio harness connector 1E to tweeter and connector 1F to driver.
Head Unit Installation
- Install U-clip nuts 9 onto dashboard bracket 8.
- Note orientation of back plate 16.
- Pass four fasteners 5 through display cover 4 , PMX head unit 3 , dashboard bracket 8 , and hand-tighten to back plate 16.
- Remove and discard cover panel.
- Join PMX head unit to audio harness.
- REF CONNECTS TO
- 1K PMX Head Unit Power
- 1N Subwoofer
- 1M White, Left Audio
- 1L Red. Right Audio
- 2 Bullet Connector
- Secure PMX head unit to dashboard with four fasteners a.
- Torque Head Unit Fasteners a (assembly to vehicle):
- Maneuver head unit assembly so that dashboard bracket is positioned inside of dashboard and cover panel is flush against dashboard front.
- Push carefully on front cover y until it snaps in place.
Vehicle Reassembly
General
Verify audio connection is operating properly before proceeding with
vehicle reassembly.
Instr 9929592 Rev 01 2019-01 Page 11 of 15
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>