YARD FORCE LX PS300 300W Portable Power Station Instruction Manual

YARD FORCE LX PS300 300W Portable Power Station Instruction Manual

SYMBLOS

Safety symbols
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them require your careful attention and full understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.

WARNING: Be sure to read and understand all safety instructions in this operator’s manual, including all safety alert symbols such as “DANGER,” “WARNING,” and “CAUTION” before using this tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION. May be used in conjunction with other symbols or pictographs.

Symbol meaning
This chapter depicts and describes safety symbols that may appear on this product.
Read, understand and follow all instructions on the machine before attempting to assemble and operate.

Read the instructions for use before use!
Batteries contain Li-ion. Do not dispose of waste batteries in domestic waste.
Contact local authority to find out how to dispose of batteries.
WEEE symbol. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
Do not throw into water.
Do not throw to fire.
Do not subject the battery to strong sunlight over long periods of time. Do not leave on a heater (max.45°C).
Do not expose to rain or water
The product complies with the applicable European directives and an evaluation method of conformity for these directives was done.

GENERAL SAFETY WARNINGS

IMPORTANT SAFETY INSTRUCTIONS

WARNING! Keep dry and do not expose to high heat.
WARNING! Never disassemble, puncture, shock, crash, short or incinerate.
WARNING! Recycle and dispose in accordance with local regulation.

When using this product, basic precautions should always be followed, including the following:

• Please read the instruction manual before using this product.
• To reduce the risk of injury, close supervision is necessary when using this product near children.
• Do not put fingers, hands or any body part into the product.
• Use of an unrecommended attachment or third-party power station manufacturer may result in a risk of fire, electric shock or injury.
• Do not use a damaged or modified battery pack or appliance.
• Do not operate the power station with a damaged cord, plug or output cable.
• When service or repair is required, do not disassemble the power pack yourself. Take the unit to a qualified service provider. Incorrect reassembly may result in a risk of fire or electric shock.
• In order to reduce the risk of electric shock when the product fails, disconnect the portable power station from the power supply before performing any instructive maintenance operations.
• Charge the internal battery in a well-ventilated area. Do not restrict ventilation.
• Under harsh conditions, liquid may be ejected from the battery. Avoid contact with the battery and liquid. If contact accidentally occurs, flush with water. If liquid contacts eyes, seek additional medical help.
• Do not expose the unit to fire or excessive heat.
• Have servicing performed by a qualified repair person only.

SAVE THESE INSTRUCTIONS

USE CARE AND SAFETY GUIDE

Do not throw into water.
Do not throw to fire.
Do not subject the battery to strong sunlight over long periods of time. Do not leave on a heater (max.45°C)

DESCRIPTION OF PRODUCT

DISPLAY

Battery Level Indicator ‒ Shows the remaining battery percentage. If your battery drops towards 0%, the battery segment on the screen will begin to blink. When this happens, please charge the device immediately.

Time display:
HOURS
– Showing the remaining charge time based on the current inlet level.
– Showing the remaining working time base on the current outlet level.

Power indicator:
INPUT
– Showing current inlet power level.

OUTPUT

– Showing current outlet power level.

Function indicator:

AC- Alternating current output function is actived.

DC USB-A – Direct current function is actived.

50HZ Actived when the alternating current output function is actived.

TECHNICAL DATA

Iutput port
DC 5521| 10-25 V max 60 W| 10-30 V max 120 W
Input/ Output port
PD Type C (1 port)| 5-20 V/ 65 W (Output)5-12 V/ 60 W (Input)| 5-20V/ 65 W (Output)5-12V/ 60 W (Input)
Output port
AC output| Pure sine wave, 300 W 230 V -50/60 Hz (2 ports)| Pure sine wave, 600 W total 230 V – 50/60 Hz (2 ports)
Max power devices supported by X-boost| 500 W| 1200 W
USB-A x1| 5 V 15 W Max (1 port)| 5 V 15 W Max (1 port)
USB-A QC| 5-12 V 18 W (1 port)| 5-12 V 18 W (1 port)
DC 5521| 12 V Max 120 W (1 port)| 13.6 V Max 120 W (2 ports)
Car charger| 12 V Max 120 W (1 port)| 13.6 V Max 120 W (1 port)

OPERATION

Charing the device

Charge the device with original adaptor

1. Connect the power plug with the adaptor.

2. Charge the device by inserting the 5521 interface to the port.
   NOTE: only use the original charging adaptor!

3. The display will show the current charging status when well connected

Charge the device with Car cigarette lighter

1. Connect the wire with the 12V port in the vehicle.

2. Charge the device by inserting the 5521 interface to the port.
   NOTE: only use the original charging adaptor!

3. The display will show the current charging statues when well connected.

Charge the device with the solar panel (sold separately)

1. Charge the device by inserting the 5521 interface to the port.
   NOTE: please pay an attenion to the inlet limitation of the port for each model! LX PS300 10-25V max 60W, LX PS600 10-30V max 120W.

Charge the device by PD type C port (not in the delivery box)
Charge the device by connecting with a type C wire to the PD type C port.

To obtain the best life from the battery

1. Never allow the device to completely discharge before recharging. The device should be placed on the charger whenever the battery pack is noticeably running down or the tool no longer performs a task it previously performed.
2. Avoid conducting short charges. Make sure that the device is fully charged each time by allowing the adaptor to complete its full charging cycle.
3. Avoid allowing loose items like screws or nails etc. to be stored with device as these or similar items can short the device and cause a fire or explosion.
4. Always unplug the device when not in use and store in a dry and secure place.
5. Avoid charging or storing your device in temperatures below 5°C and above 45°C.
6. After use, allow the device to cool down for approximately 30 minutes before attempting to recharge

Switch ON the device

• Press the button for 3s to switch on the device, DC output will be actived accordingly.
• When the device is powered ON, all the DC ports are ready to use.
  

Active the AC function

• Press the button, the “AC” mark will light on in the display which means the 2 AC ports are ready to use.
  

Charging cycle and working hours

MAINTENANCE AND STORAGE

CLEAN
Caution! Protect the product from direct contact with water, and make sure that water doesn’t get the opportunity to get in.

• Always clean the product thoroughly after each use with a damp cloth, sponge or brush.
• Avoid oil and grease contamination (especially to gripping parts).
• If contamination should occur, wipe the product with a damp cloth moistened with soapy water.
• Never use aggressive cleaning agents, solvents or chemicals for cleaning. Permanent damage to plastic parts could occur.

STORAGE

• Store the machine out of reach of children.
• Don’t store the product in direct sunlight for long periods.
• For safety reasons worn or damaged parts should be replaced.
• Store in the original packaging (if possible) in a clean, dry, dark and frost-free place protected from dust and out of reach of children.
• Cover unit with a suitable protective cover that does not retain moisture. Do not use sheet plastic as a dust cover. A nonporous cover will trap moisture around the machine, promoting rust and corrosion.
• The ideal storage temperature is between 5 °Cand 30 °C.

DISPOSAL

• Dispose your device, accessories and packaging in accordance with the requirements of environmental protection into the recycling collection center.
• This machine does not belong to the household waste. Save the environment and take this device to designated collection points where it will be received for free. For more information please contact your local authority or nearest collection point. Improper disposal may be punished according to national regulations.
• The battery contains toxic substances. Toxic materiaIs must be disposed of in a specified manner in order to prevent contamination of the environment. Take used batteries to a recycling center. Do not throw the battery into household waste, fire or water.

How do I care for the power station?
This power station is designed for a variety of uses so there is a good chance our device will need a little cleaning every now and then.
Please use a dry, non-abrasive cloth. We like the cleaners that have been designed for mobile phone and computer screens if you need a little extra oomph. Do not give it a bath!

How do I store the power station?
Please store your power station in a dry environment out of direct elements. For optimal battery health, store the device at room temperature 80% charged. This device offers a water-resistant, dustproof case for maximum protection. We suggest that you keep your connected to a power source when not in use, like a solar panel or a wall plug, so it keeps its battery healthy and topped over. This prolongs battery life and will ensure your power station is ready to recharge your gear at all times.

How do I use the power station safely?
Please use the power station in temperature conditions inside of its operating temperature range. Using it outside of its optimal temperature operating range can push it beyond its safe and effective limits.
Do not submerge your power station. It is not waterproof and this will void your warranty.

Don’t throw the power station around. Treat it like the equipment you are plugging into it, with care.

WARNING! Do not charge the machine immediately after it is fully discharged. For safety, please cool the battery before charging!

DECLARATION OF CONFORMITY

To the provisions of Council Directives

We
MEROTEC GmbH
Otto-Brenner-Str. 8
47877 Willich
Germany
Declare that the product:
Machine Description: Power station
LX PS300/ NV300
LX PS600/ NV600

Complies with the essential health and safety requirements of the following directives:

Low Voltage Directive 2014/35/EU
Electromagnetic Compatibility Directive 2014/30/EU
EC Directive 2011/65/EU and its amendment Directive (EU) 2015/863 (RoHS)

Standards and technical specification referred to :
EN 62368-1:2020+A11+2020
EN 55032:2015+A1:2020+A11:2020
EN IEC 61000-3-2:2019+A1:2021
EN 61000-3-3:2013+A1:2019+2019+A2:2021

Authorized Signatory
Date: 04.11.2022
Signature:
Place: Willich
Name: Roland Menken
General Manager

MEROTEC GmbH
Otto-Brenner-Str. 8, 47877 Willich, Germany

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>