BIG DOG Wireless Bluetooth Speakers User Guide

BIG DOG Wireless Bluetooth Speakers

Product Description

BUTTON FUNCTION

• POWER ON Press Power button around 1.55 to power on
• POWER OFF Press Power button around 25
• PLAY/PAUSE Press Play/Pause button
• VOLUME DOWN Press Volume Down button
• VOWME UP Press Volume Up button
• PREY Hold Volume Down button
• NEXT Hold Volume up button
• SWITCH MODE Hold Mode button around 2s to switch BT,TF,U5B disk,AUX mode
• EQ Press Mode button for different EQ (full sound mode I bass mode /natural sound)
• PICKUP CALL Press Play/Pause button
• REJECT CALL Press Play/Pause button 25
• END CALL Press Play/Pause button
• REDIAL Press Play/Pause button twice
• BLUETOOTH DISCONNECT Hold Play/Pause button around 35

Specification

Bluetooth – When powered on, Bluetooth is on automatically, the blue light will flash quickly, the light will stay on when connected.
TWS Stereo Pairing –

1. Power on the two speakers;
2. Press the power button twice, the speaker will move to TWS paring status with a beep tone and a flashing yellow light, when pairing successfully, the two speaker’s yellow lights will stay on, then the blue light will flash on the master speaker while the mobile device is connecting.
3. When they are connected, press the power button twice to disconnect the pairing and the yellow light will turn off;
4. The two speakers can be paired automatically after powered on if the two speakers have paired before.

Bluetooth Distance – around 18m (depending on the environment)
TWS Distance – around 6m (depending on the environment)

PROMPT| Power On Prompt – Dag bark Power Off Prompt – Dog whine
OTHER| Waterproof – IPX6
DSP-Yes
Max Loud – 105dBA
Stand-By Time – Shuts down automatically after 10 mins if there is no
Bluetooth connection
Logo – Metal logo with wire appearance
SPEAKER| Drivers – Two drivers, dia 57mm Radiators – Two radiators, dia 60mm Total RMS Power – 2x20W
PORT FUNCTION| Type-C Port – Charging port
AUX Port – Plays aux source when plugged into aux cable
TF Card Port – Plays TF card source when plugged into TF card
USB·A Port – Plays USB source when plugged into USB disk
USB·A Port – Charges other devices when plugged into charging cable
LED STATUS| AUX Mode – Blue light flashes when playing music, blue light stays on when paused
TF Card Mode – Blue light flashes when playing music, blue light stays on when paused
U Disk Model – Blue light flashes when playing music, blue light stays on when paused
RGB – Slow flash – run light – off RGB
TWS

1. Waiting to pair: The yellow light is flashing

2. When paired successfully: The yellow light stays on and the blue light flashes
   EQ Switch –

3. Blue light is full sound made,

4. Green light is bass mode,

5. White light is natural sound.

Chargin

1. Red light will slowly flash when charging
2. Red light will stay on when fully charged
3. Charge time is around 3 hours

Low Power- Red light will flash

BATTERY| Battery Type – Lithium Ion battery pack
Capacity- 7.2V 2500mAh / 18WH
Play Time -15 hours at around 15% volume
ADDITIONAL ACCESSORIES| Charging Cable – USB A-type C, length 50cm
User Manual – General Manual
3.5mm AUX Cable – 3.5mm – 3.5mm cable, length 50cm
Strap-Yes

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>