BOSS RC 505 mkll Loop Station User Guide
- June 13, 2024
- Boss
Table of Contents
BOSS RC 505 mkll Loop Station
Product Information
Version | Parameter Guide |
---|---|
Version 1.2 and later | Parameter indications in this guide Parameters that |
were added
or changed in Ver. 1.2 are indicated with a Ver. 1.2 mark.
Rhythm Pattern List
Click here to view the complete Rhythm Pattern List.
Memory Settings (LOOP)
Parameter | Value (Bold: default) | Explanation |
---|---|---|
REVERSE | OFF, ON | Specifies conventional playback (OFF) or reverse playback |
(ON).
When REVERSE is set to ON, you won’t be able to switch to
overdubbing after a recording has been completed.
1SHOT PAN PLAY LEVEL START MODE STOP MODE DUB MODE FX| OFF| Conventional loop
playback. The phrase will play only once from
the beginning to the end of the track, and then stop automatically
(One-Shot Playback).
| ON| If you press the [J/t] button during playback, playback will
begin again from the beginning of the track (Retrigger Playback).
Overdubbing cannot be carried out. If you don’t want to use tempo
synchronization, set TEMPO SYNC SW (p. 3) OFF.
1SHOT PAN PLAY LEVEL START MODE STOP MODE DUB MODE FX| IMMEDIATE| Playback
starts immediately.
| FADE| Playback starts while fading in. You can use FADE TIME (p. 4)
to specify the length of the fade-in.
1SHOT PAN PLAY LEVEL START MODE STOP MODE DUB MODE FX| IMMEDIATE| Playback
will stop immediately.
| FADE| Playback will fade out and then stop. You can use FADE TIME (p.
4) to specify the length of the fade-out.
| LOOP| Playback will continue to the end of the loop, and then
stop.
1SHOT PAN PLAY LEVEL START MODE STOP MODE DUB MODE FX| OVERDUB| The new
performance is layered onto the prerecorded tracks. If
overdubbing is repeated, the next performance is layered on top of
the previous material, allowing you to create an ensemble in a
single track.
| REPLACE1| Tracks with existing recordings are overwritten as new tracks
are recorded over them. Overwriting takes places while the
previously recorded tracks are played back, allowing you to achieve
a kind of delay effect similar to that obtained from an effects
processor.
| REPLACE2| Tracks with existing recordings are overwritten as new tracks
are recorded over them. You can record over a track that has
already been recorded, without playing that track.
| OFF, ON| Specifies whether to apply input/track FX (ON) or not
(OFF).
| MULTI:| Track 1 Track 2
PLAY MODE| SINGLE:| Track 1 Track 2
| MULTI| Stops when the other track starts playing. Play back all
tracks. To ensure that playback always takes place from the
beginning of the phrase, you need to set LOOP SYNC SW (p. 3) to
OFF.
| SINGLE| Play back only a single track. The currently-playing track
stops when the other track starts playing. If SINGL CHNGE is set to
LOOP END, the track will change at the end of the loop.
Version 1.2 and later
Parameter Guide
© 2021 Roland Corporation
Parameter indications in this guide
Parameters that were added or changed in Ver. 1.2 are indicated with a Ver.
1.2 mark.
Memory Settings (LOOP)
TRACK 15
- You can press the [TRACK] buttons for tracks 15 to show the track settings screen for each track.
Parameter REVERSE
Value (Bold: default)
Explanation
OFF, ON
Specifies conventional playback (OFF) or reverse playback (ON).
- When REVERSE is set to “ON”, you won’t be able to switch to overdubbing after a recording has been completed.
Specifies whether the track playback will be one-shot (ON) or not one-shot (OFF; conventional loop playback).
Track 1: OFF Track 2: ON
If 1SHOT is ON, playback will stop when it reaches the end of the phrase.
1SHOT PAN PLAY LEVEL START MODE
STOP MODE
DUB MODE FX
OFF
Conventional loop playback.
The phrase will play only once from the beginning to the end of the track, and then stop automatically (One-Shot Playback).
ON
If you press the [J/t] button during playback, playback will begin again from the beginning of
the track (Retrigger Playback). Overdubbing cannot be carried out.
- If you don’t want to use tempo synchronization, set TEMPO SYNC SW (p. 3) “OFF”.
L50CENTERR50
Specifies the stereo position (pan) of the track.
0100200
Adjusts the playback level of the tracks.
Specifies whether playback starts with a fade-in or immediately when the track plays.
IMMEDIATE
Playback starts immediately.
FADE
Playback starts while fading in. * You can use “FADE TIME” (p. 4) to specify the length of the fade-in.
Specifies how the track will stop when you press the [9] button. 5 The [J/t] button will blink until playback stops. 5 If you press the [9] button once again before playback stops, playback will stop immediately. * You can’t overdubbing during the time until playback stops.
IMMEDIATE
Playback will stop immediately.
FADE
Playback will fade out and then stop. * You can use “FADE TIME” (p. 4) to specify the length of the fade-out.
LOOP
Playback will continue to the end of the loop, and then stop.
Specifies the overdubbing method.
OVERDUB
The new performance is layered onto the prerecorded tracks.
If overdubbing is repeated, the next performance is layered on top of the
previous material, allowing you to create an ensemble in a single track.
REPLACE1
Tracks with existing recordings are overwritten as new tracks are recorded over them. Overwriting takes places while the previously recorded tracks are played back, allowing you to achieve a kind of delay effect similar to that obtained from an effects processor.
REPLACE2
Tracks with existing recordings are overwritten as new tracks are recorded over them. You can record over a track that has already been recorded, without playing that track.
OFF, ON
Specifies whether to apply input/track FX (ON) or not (OFF).
Specifies whether tracks 1 and 2 play back simultaneously.
MULTI:
Track 1 Track 2
PLAY MODE
SINGLE: Track 1 Track 2
MULTI
SINGLE
Stops when the other track starts playing.
Play back all tracks. To ensure that playback always takes place from the
beginning of the phrase, you need to set
LOOP SYNC SW (p. 3) to “OFF”. Play back only a single track. The currently-
playing track stops when the other track starts playing. If SINGL CHNGE is
set to “LOOP END”, the track will change at the end of the loop.
2
Parameter MEASURE
LOOP SYNC
TEMPO SYNC BOUNCE IN INPUT
Memory Settings (LOOP)
Value (Bold: default)
Explanation
You can specify the number of measures for each track. When recording along with rhythm sounds or other tracks, it’s convenient to specify the number of measures before you record, so that looping will occur at the specified measure length, even if you don’t operate the switch when you’ve finished recording.
- This parameter is available only if LOOP SYNC SW is “ON”.
Track 1: One measure
Track 2: Four measures
AUTO
Tracks that are set to AUTO will have the same number of measures. The number
of measures is determined by the first-recorded track of the tracks that are
set to AUTO.
For example, if all tracks are set to AUTO, the value set as the number of
measures for the second and subsequent tracks will be identical to the number
of measures in the first track that was recorded.
FREE
The number of measures will be set automatically, corresponding to the length of the recording.
~1
The number of measures will be set manually. If you select a note, you can
make the length shorter than a single measure. Ver. 1.2 * When LOOP SYNC MODE
is set to “LOOP LENGTH” (p. 3), the number of measures is adjusted
according to the length set in LOOP LENGTH.
Sets whether to use loop sync (ON) or not (OFF).
When loop sync is used, the memory’s tempo or the tempo synchronized to
another track whose LOOP SYNC SW is “ON” is used for recording and playback.
Ver. 1.2
SW
OFF
Records or plays back when you press the buttons.
This lets you play back a loop with an unspecified length, without syncing to
the memory’s tempo or to the tempo of another track.
ON
The tempo that’s used for recording or playback is either the memory’s tempo or the tempo synchronized to another track whose LOOP SYNC SW is “ON”.
Sets how the loop sync operates (how syncing is performed).
IMMEDIATE Recording or playback starts right when you press the buttons. The length of the track to be recorded is adjusted in units of one measure.
Ver. 1.2
MODE
MEASURE
Recording or playback starts at the beginning of a measure. The length of the track to be recorded is adjusted in units of one measure. Tracks that are played back start at the beginning of the phrase, in time with the beginning of other tracks and measures.
LOOP LENGTH
Recording or playback starts at the beginning of a measure. The length of the track to be recorded is adjusted according to the length set in LOOP LENGTH (p. 4). The track to be played back starts in time with the beginning of other tracks, in units set by LOOP LENGTH.
Specifies whether each track plays at its original tempo (the tempo during recording) or at the tempo that is
specified in memory.
SW
OFF
The track will play at its own original tempo.
ON
The track will play at the memory tempo. Tracks 15 play at the same tempo.
MODE
When TEMPO SYNC SW is “ON”, this sets whether to change the pitch according to the tempo, or to instead make the pitch stay the same.
PITCH
The pitch changes according to the tempo.
XFADE
Adjusts the playback speed to match the tempo without changing the pitch.
SPEED
Sets the playback speed for each track.
- You can change the timing at which the playback speed is switched from the LOOP/PLAY “SPEED CHANGE” (p. 4) setting.
HALF
Plays back at half the speed of the original tempo.
NORMAL Plays back at the original tempo.
DOUBLE Plays back at twice the speed of the original tempo.
OFF, ON
Sets whether to allow the playback sound from a different track as well to be recorded (ON) or not (OFF) during recording or overdubbing.
MIC 1, 2
INST1 L, R OFF, ON
INST2 L, R
RHYTHM
Sets whether the sound from each input jack/connector and the rhythm should be
inputted to the track (ON) or not (OFF) during recording.
Turn the [1] knob to select the input jack/connector or RHYTHM, and press the
[1] knob to switch between ON/OFF.
- When STEREO LINK (p. 9) is “ON”, the MIC 1, 2 and L/R channels are shown as a single connector.
3
Memory Settings (LOOP)
REC
Parameter REC ACTION
QUANTIZE
AUTO REC BOUNCE SW BOUNCE TRACK
Value (Bold: default)
Explanation
Specifies the order in which record/playback/overdubbing are switched when you press the [J/t] button.
REC->DUB
Operation will switch in the order of Recording 0 Overdubbing 0 Playback.
REC->PLAY
Operation will switch in the order of Recording 0 Playback 0 Overdubbing.
With tracks for which LOOP SYNC SW (p. 3) is “ON”, under any of the conditions
listed below, your timing will be corrected (Loop Quantize) based on the tempo
and time signature of the rhythm, even if the timing at which you press a
button is slightly inaccurate. 5 If the rhythm is on 5 If there is an already-
recorded track whose LOOP SYNC SW is turned on 5 If the MIDI Sync is on The
QUANTIZE setting applies only during recording. It is ignored during
overdubbing or playback. When you stop recording, it is quantized to match
the measure length of the previously-recorded track (LOOP SYNC SW:
ON) or rhythm.
OFF
Recording begins the instant you perform the operation. When you stop recording, it is quantized to match the measure.
MEASURE
Quantize to the measure start location for recording.
“AUTO REC” (auto record) starts recording when there is audio input from the mic or your guitar performance.
OFF
Recording will begin the instant you press the [J/t] button.
SW ON
When you press the [J/t] button, the [J/t] button will blink rapidly, and the
RC-505mk2 will enter recording-standby mode.
When you begin playing, the [J/t] button will light and recording will start.
SENS 150100
Specifies the input sensitivity at which auto record starts. Recording will start when the input from the mic or guitar exceeds the specified sensitivity.
- This is valid when AUTO REC SW is “ON”.
OFF, ON
Sets whether bounce recording is used (ON) or not (OFF).
15 OFF, ON
Specifies the track used for input during bounce recording (the track used for bouncing).
PLAY
Parameter S.TRK CHANGE CURRENT TRACK FADE TIME ALL START TRK ALL STOP TRK LOOP
LENGTH SPEED CHANGE
SYNC ADJUST
Value (Bold: default)
Explanation
Specifies how the tracks will be switched when PLAY MODE (p. 2) is “SINGLE”.
IMMEDIATE
The change will occur immediately.
Ver. 1.2 * When LOOP SYNC MODE (p. 3) is set to “MEASURE”, the track switches
at the beginning of the next measure.
LOOP END
The change will occur after playback has reached the end of the loop.
MEASURE
The change will occur beginning of the next measure.
TRACK15
Sets the target track for operating and editing.
Specifies the fade-in time as a number of measures when START MODE (p. 2) is set to “FADE”.
IN
~, , ¸, ,
If you select a note, you can make the length shorter than a single measure.
1MEAS2MEAS
OUT 64MEAS
Specifies the fade-out time as a number of measures when STOP MODE (p. 2) is set to “FADE”. If you select a note, you can make the length shorter than a single measure.
15 OFF, ON
Set this to “ON” for tracks that should start playing when MIDI start data is received. Use the [1][2] knobs to select the track, and press the [1][2] knobs to turn the setting on/off.
15 OFF, ON
Set this to “ON” for tracks that should stop playing when MIDI stop data is received. Use the [3][4] knobs to select the track, and press the [3][4] knobs to turn the setting on/off.
Specifies the length to which LOOP SYNC (p. 3) aligns the beginnings of the material for loop sync.
AUTO
The length of the first-recorded phrase will be the LOOP LENGTH.
125362
Manually specifies the number of measures that will be looped.
Specifies the timing at which the playback speed switches to the speed set in TEMPO SYNC SPEED (p. 3).
IMMEDIATE
The change will occur immediately.
LOOP END
The change will occur after playback has reached the end of the loop.
When SPEED CHANGE is set to “IMMEDIATE”, this sets the conditions for synchronizing the start of the tracks.
MEASURE
The starting points of the tracks are synchronized if they are out of alignment by one measure or less.
BEAT
The starting points of the tracks are synchronized if they are out of alignment by one beat or less.
4
INPUT FX
BANK AD
Parameter FX AD BANK SW
MODE
FX TARGET
Memory Settings (LOOP)
Value (Bold: default)
Explanation
OFF, ON
Specifies the FX AD on/off. * When MODE is set to “SINGLE”, you can turn on only one effect from AD.
AD
Sets the target FX bank for operating and editing.
OFF, ON
Specifies the FX bank on/off.
Sets how the [A][D] buttons operate.
SINGLE
The effect for only one button you push can be turned on.
MULTI
The effects for all the buttons you push can be turned on.
AD
Sets which effect is controlled (FX AD) when using the [INPUT FX] knob.
FX AD
Parameter SW SW MODE
INSERT
FX TYPE
Value (Bold: default)
Explanation
OFF, ON
Specifies the effects on/off.
Sets how the [A][D] buttons operate.
TOGGLE
The effect toggles between on and off with each press of the button.
MOMENT
The effect turns on only while the button is pressed.
These parameters set the inputs for which effects are applied. * When STEREO LINK is “ON”, the L/R channels of MIC 1, 2 are shown as a single connector.
Applies effects to all inputs.
- Even when this is set to “ALL”, the unit doesn’t record inputs with effects if the LOOP/TRACK
ALL
15 INPUT (p. 3) for all the tracks hasn’t been set to “ON”.
- Even when this is set to “ALL”, the signal with effects is not output to the output jacks whose
INPUT (p. 12) in MENU/OUTPUT/ROUTING are not all set to “ON”.
MIC1, MIC2
Applies effects to the input audio from the MIC 1, 2 connectors.
INST1-L, INST1-R
Applies effects to the input audio from the INST 1 L/MONO, R jacks.
INST2-L, INST2-R
Applies effects to the input audio from the INST 2 L/MONO, R jacks.
Select the type of effect to assign to the [A][D] buttons, and set their FX parameters. * The FX parameters vary depending on the selected effect type.
&”Input FX/Track FX List” (p. 34)
5
Memory Settings (LOOP)
TRACK FX
BANK AD
Parameter FX AD BANK SW
MODE
FX TARGET
Value (Bold: default)
Explanation
OFF, ON
Specifies the FX AD on/off. * When MODE is set to “SINGLE”, you can turn on only one effect from AD.
AD
Sets the target FX bank for operating and editing.
OFF, ON
Specifies the FX bank on/off.
Sets how the [A][D] buttons operate.
SINGLE
The effect for only one button you push can be turned on.
MULTI
The effects for all the buttons you push can be turned on.
AD
Sets which effect is controlled (FX AD) when using the [INPUT FX] knob.
FX AD
Parameter SW SW MODE
INSERT
FX TYPE
Value (Bold: default)
Explanation
OFF, ON
Specifies the effects on/off.
Sets how the [A][D] buttons operate.
TOGGLE
The effect toggles between on and off with each press of the button.
MOMENT
The effect turns on only while the button is pressed.
These parameters set the tracks for which effects are applied.
Applies effects to all tracks.
ALL
- Even when this is set to “ALL”, the signal with effects is not output to the output jacks whose
TRACK (p. 11) in MENU/OUTPUT/ROUTING are not all set to “ON”.
TRACK15
Applies effects to specified tracks.
Select the type of effect to assign to the [A][D] buttons, and set their FX parameters. * The FX parameters vary depending on the selected effect type.
&”Input FX/Track FX List” (p. 34)
6
Memory Settings (LOOP)
RHYTHM
- You can access the rhythm setting screen by pressing the RHYTHM [EDIT] button.
MEMO By executing the Write operation while in the rhythm play-standby or rhythm play condition, you can save/recall the memory as a “rhythm: on” memory.
Parameter GENRE PATTERN VARIATION KIT BEAT
START TRIG
STOP TRIG
INTRO REC INTRO PLAY ENDING FILL VAR.CHANGE
Value (Bold: default)
Explanation
Selects the genre of the rhythm pattern.
ACOUSTIC, BALLAD, BLUES, JAZZ, FUSION, R&B, SOUL, FUNK, POP, SOFT ROCK, ROCK, ALT ROCK, PUNK, HEAVY ROCK, METAL, TRAD, WORLD, BALLRM, ELCTRO, GUIDE, USER
Selects the rhythm pattern. * The patterns you can select vary, depending on the genre.
&”Rhythm Pattern List” (p. 44)
AD
Selects the rhythm pattern variation.
Selects the drum kit that is used for rhythm playback.
STUDIO, LIVE, LIGHT, HEAVY, ROCK, METAL, JAZZ, BRUSH, CAJON, DRUM&BASS, R&B, DANCE, TECHNO, DANCE BEATS, HIPHOP, 808+909
2/44/47/4, 5/815/8
Selects the rhythm beat. * You cannot change the beat after the track is recorded. Be sure to set this before recording.
Specifies how rhythm playback starts.
LOOP START
The rhythm plays when loop recording or playback starts.
REC END
The rhythm plays when loop recording ends and switches to playback.
This is useful if you want to perform without specifying a tempo, then start
recording, and then play the loop in time with the rhythm when playback
starts.
BEFORE LOOP
The rhythm plays before loop recording or playback.
The rhythm starts playing when you press the button once, and
recording/playback starts in time with the rhythm when you press the button
once again.
Specifies how rhythm playback stops.
The rhythm always continues playing.
OFF
If you are performing in synchronization with an external MIDI device, you can keep the
rhythm playing continuously to allow synchronized playback.
LOOP STOP
The rhythm stops when the loop stops.
REC END
The rhythm stops when loop recording ends. This is useful when you want to use the rhythm as a guide during recording.
OFF, ON
Sets whether to add an intro (ON) or not (OFF) when recording. * The intro does not play while a track or rhythm is being played back.
OFF, ON
Specifies whether the rhythm plays with (ON) or without (OFF) an intro.
OFF, ON
Specifies whether the rhythm plays with (ON) or without (OFF) an ending.
OFF, ON
Specifies whether the rhythm plays with a fill-in (ON) or without a fill-in (OFF).
Specifies the timing at which the rhythm pattern variation is switched.
MEASURE
Play to the end of the measure and then switch.
LOOP END
Play to the end of the loop and then switch.
7
Memory Settings (LOOP)
NAME
Parameter
NAME
Value (Bold: default)
Explanation
Specifies the memory name.
1. Turn the [4] knob to move the cursor to the position at which you want to enter a character.
2. Turn the [3] knob to select a character.
[1] knob [2] knob
Turn Press Turn Press
Jumps to the beginning of uppercase/lowercase characters, numbers or symbols Deletes the character at the cursor position Toggles between uppercase/lowercase Inserts a space at the cursor position
8
System Settings (MENU)
INPUT
SETUP
Parameter PHANTOM INST1 GAIN INST2 GAIN
STEREO LINK
PREFERENCE
Value (Bold: default)
Explanation
MIC1 MIC2
OFF, ON
Turns phantom power on/off.
- Always turn the phantom power off when connecting any device other than condenser microphones that require phantom power.
These parameters set the gain for INST 1 and 2 to match that of the connected devices.
INST
Instruments such as guitars/bass guitars, keyboards, etc.
LINE
Line-level equipment such as audio players
MIC INST1 INST2
OFF, ON OFF, ON
Turns the stereo link function on/off. 5 When MIC is set to “ON”, this
collectively uses the same settings for the MIC 1 and 2
connectors. 5 When INST 1, 2 is set to “ON”, this collectively uses the same
settings for the L and R jacks.
MIC INST1 INST2
SYSTEM, MEMORY
Selects whether to switch the MIC 1, 2 and INST 1, 2 settings to either the settings for each memory or to the system settings.
- When switching to the settings for each memory, use the write operation to save the settings to memory.
EQ
9 MIC1, MIC2, INST1 L, INST1 R, INST2 L, INST2 R
- When STEREO LINK (p. 9) is “ON”, MIC, INST 1 and INST 2 are shown.
Parameter SW LO GAIN HIGH GAIN
FREQ
LO MID Q
GAIN FREQ
HI MID Q
LEVEL
GAIN
LO CUT
Value (Bold: default) OFF, ON -200+20 dB -200+20 dB 20.0250 HZ10.0 kHz
0.516
-200+20 dB 20.0800 HZ10.0 kHz
0.516
-200+20 dB -200+20 dB
FLAT, 20800 Hz
HI CUT
630 Hz12.5 kHz, FLAT
Explanation Turns equalizer on/off. Adjusts the gain for the low frequency range. Adjusts the gain for the high frequency range. Specifies the center of the frequency range that will be adjusted by the LO MID GAIN. Adjusts the width of the area affected by the EQ centered at the LO MID FREQ. Higher values will narrow the area. Adjusts the gain for the low-middle frequency range. Specifies the center of the frequency range that will be adjusted by the HI MID GAIN. Adjusts the width of the area affected by the EQ centered at the HI MID FREQ. Higher values will narrow the area. Adjusts the gain for the high-middle frequency range. Adjusts the overall volume level of the equalizer. Specifies the frequency at which the low cut filter begins to take effect. When “FLAT” is selected, the low cut filter will have no effect. Specifies the frequency at which the high cut filter begins to take effect. When “FLAT” is selected, the high cut filter will have no effect.
9
System Settings (MENU)
DYNAMICS
Parameter
Value (Bold: default)
MIC1 (*1)
COMP OFF, 1100
NS
040100
MIC2 (*1)
COMP OFF, 1100
NS
040100
INST 1 NS
040100
INST 2 NS
040100
Explanation
Specifies the depth of the compressor that is applied to the audio input from
the MIC 1 during loop recording. When this is “OFF”, no compressor effect is
applied.
Specifies the depth of the noise suppressor that is applied to the audio input
from the MIC 1 during loop recording.
Specifies the depth of the compressor that is applied to the audio input from
the MIC 2 during loop recording. When this is “OFF”, no compressor effect is
applied.
Specifies the depth of the noise suppressor that is applied to the audio input
from the MIC 2 during loop recording.
Specifies the depth of the noise suppressor that is applied to the audio input
from the INST 1 during loop recording.
Specifies the depth of the noise suppressor that is applied to the audio input
from the INST 2 during loop recording.
(*1) When STEREO LINK (p. 9) is “ON”, MIC is shown.
10
System Settings (MENU)
OUTPUT
SETUP
Parameter OUTPUT KNOB
STEREO LINK
PREFERENCE
Value (Bold: default)
Explanation
These parameters select which output levels are adjusted using the [OUTPUT LEVEL] knob.
ALL
Adjusts the MASTER OUT and PHONES OUT.
MASTER
Adjusts the general output level (MASTER OUT) for MAIN/SUB 1/SUB 2.
PHONES
Adjusts the PHONES output level (PHONES OUT).
This can’t be adjusted with the [OUTPUT LEVEL] knob.
OFF
The output level used is the level adjusted in the MIXER screen (p. 13) for each output jack.
MAIN SUB1 SUB2
OFF, ON
Turns the stereo link function on/off. When set to “ON”, this collectively uses the same settings for the L and R jacks.
MAIN
SUB1
SUB2
SYSTEM,
PHONES MEMORY
RHYTHM
Select whether to make the settings for each output jack, for the rhythm sounds (RHYTHM) and for the MASTER FX settings (MFX) apply to each memory individually or to the system.
- When switching to the settings for each memory, use the write operation to save the settings to memory.
MFX
ROUTING
9 TRACK
- If these are set individually to ON/OFF for the tracks to be output from each jack, the effect sounds for which TRACK FX’s INSERT (p. 6) is set to “ALL” are not output.
Parameter
Value (Bold: default)
Explanation
MAIN-L, R (*2)
15
OFF, ON
Sets the track to output to MAIN.
Turn the [1] or [2] knob to select the track, and press the [1] or [2] knob to
switch between ON/ OFF.
SUB1-L, R (*2)
15
OFF, ON
Sets the track to output to SUB 1.
Turn the [3] or [4] knob to select the track, and press the [3] or [4] knob to
switch between ON/ OFF.
SUB2-L, R (*2)
15
OFF, ON
Sets the track to output to SUB 2.
Turn the [1] or [2] knob to select the track, and press the [1] or [2] knob to
switch between ON/ OFF.
PHONES (*3)
15
OFF, ON
Sets the track to output to PHONES.
Turn the [3] or [4] knob to select the track, and press the [3] or [4] knob to
switch between ON/ OFF.
(2) When STEREO LINK is “ON”, MAIN, SUB 1 and SUB 2 are shown. (3) This is shown when the SW parameter of ROUTING/PHONES OUT (p. 12) is set to “INDIVIDUAL”.
11
System Settings (MENU)
9 INPUT/RHYTHM
Parameter
Value (Bold: default)
Explanation
MAIN (*4)
MIC 1, 2 INST 1 L, R INST 2 L, R RHYTHM
OFF, ON
Sets whether to output the input and rhythm sounds from MIC 1, 2/INST 1, 2 to
MAIN (ON) or not (OFF).
Use the [1][4] knobs to move the cursor, and press the [1][4] knobs to
switch between ON/ OFF.
SUB1 (*4)
MIC 1, 2 INST 1 L, R INST 2 L, R RHYTHM
OFF, ON
Sets whether to output the input and rhythm sounds from MIC 1, 2/INST 1, 2 to
SUB 1 (ON) or not (OFF).
Use the [1][4] knobs to move the cursor, and press the [1][4] knobs to
switch between ON/ OFF.
SUB2 (*4)
MIC 1, 2 INST 1 L, R INST 2 L, R RHYTHM
OFF, ON
Sets whether to output the input and rhythm sounds from MIC 1, 2/INST 1, 2 to
SUB 2 (ON) or not (OFF).
Use the [1][4] knobs to move the cursor, and press the [1][4] knobs to
switch between ON/ OFF.
- This is shown when the SW parameter of ROUTING/PHONES OUT is set to “INDIVIDUAL”.
PHONES (*4)
MIC 1, 2 INST 1 L, R INST 2 L, R RHYTHM
OFF, ON
Sets whether to output the input and rhythm sounds from MIC 1, 2/INST 1, 2 to
PHONES (ON) or not (OFF).
Use the [1][4] knobs to move the cursor, and press the [1][4] knobs to
switch between ON/ OFF.
- This is shown when the SW parameter of ROUTING/PHONES OUT is set to a value aside from “INDIVIDUAL”.
PHONES RHYTHM OFF, ON
Sets whether to output the input and rhythm sounds from MIC 1, 2/INST 1, 2 to PHONES (ON) or not (OFF).
This sets the output destination of the rhythm sound.
RHYTHM OUT INPUT THRU
OUTPUT LOOP OFF, ON
Outputs from the output jack that’s set to “ON” in RHYTHM.
Lets you record rhythm sounds in a loop, or perform loops while using the note
messages from an external MIDI device to trigger the rhythm. When this is set
to “OFF”, the input sound from the MIC 1/2 and INST 1/2 jacks is muted and is
not output to all OUTPUT jacks.
(*4) When STEREO LINK (p. 9) is “ON”, the MIC 1, 2 and L/R channels are shown as a single connector.
9 PHONES OUT
- If these are set individually to ON/OFF for the tracks to be output from each jack in the ROUTING/TRACK (p. 11) settings, the effect sounds for which INPUT FX’s INSERT (p. 5) is set to “ALL” are not output.
Parameter SW
Value (Bold: default)
Explanation
These parameters specify the track to output from the PHONES jack. * When STEREO LINK (p. 11) is “ON”, MAIN, SUB 1 and SUB 2 are shown.
MAIN-L, R
The track set in “MAIN-L, R” (p. 11) of ROUTING/TRACK is output.
SUB1-L, R
The track set in “SUB1-L, R” of ROUTING/TRACK is output.
SUB2-L, R
The track set in “SUB2-L, R” of ROUTING/TRACK is output.
INDIVIDUAL
The track set in “PHONES” of ROUTING/TRACK is output.
9 PHONES MONITOR
- This is shown when the SW parameter of ROUTING/PHONES OUT is set to “INDIVIDUAL”.
Parameter
Value (Bold: default)
PHONES MONITOR OFF, ON
Explanation
When this is set to “ON”, the track’s sound always plays back through the
PHONES jack, regardless of the track slider position.
12
System Settings (MENU)
EQ
9 MAIN L, MAIN R, SUB1 L, SUB1 R, SUB2 L, SUB2 R
- When STEREO LINK (p. 11) is “ON”, MAIN, SUB1 and SUB2 are shown.
Parameter SW LO GAIN HIGH GAIN
FREQ
LO MID Q
GAIN FREQ
HI MID Q
LEVEL
GAIN
LO CUT
Value (Bold: default) OFF, ON -200+20 dB -200+20 dB 20.0250 Hz10.0 kHz
0.516
-200+20 dB 20.0800 Hz10.0 kHz
0.516
-200+20 dB -200+20 dB
FLAT, 20800 Hz
HI CUT
630 Hz12.5 kHz, FLAT
Explanation Turns equalizer on/off. Adjusts the gain for the low frequency range. Adjusts the gain for the high frequency range. Specifies the center of the frequency range that will be adjusted by the LO MID GAIN. Adjusts the width of the area affected by the EQ centered at the LO MID FREQ. Higher values will narrow the area. Adjusts the gain for the low-middle frequency range. Specifies the center of the frequency range that will be adjusted by the HI MID GAIN. Adjusts the width of the area affected by the EQ centered at the HI MID FREQ. Higher values will narrow the area. Adjusts the gain for the high-middle frequency range. Adjusts the overall volume level of the equalizer. Specifies the frequency at which the low cut filter begins to take effect. When “FLAT” is selected, the low cut filter will have no effect. Specifies the frequency at which the high cut filter begins to take effect. When “FLAT” is selected, the high cut filter will have no effect.
MASTER FX
Parameter COMP REVERB INSERT
Value (Bold: default)
OFF, 140 040
MAIN-L, MAIN-R, SUB1-L, SUB1-R, SUB2-L, SUB2-R, OFF
Explanation
Sets the depth of the compressor effect that’s applied to the output sound.
When this is “OFF”, no compressor effect is applied.
Sets the depth of the reverb effect that’s applied to the output sound.
Sets the output jacks to which the compressor and reverb effects are applied.
When this is “OFF”, no compressor or reverb effects are applied. * When STEREO
LINK (p. 11) is “ON”, MAIN, SUB1 and SUB2 are shown.
MIXER
Parameter MIC 1, 2 IN INST1-L, R IN INST2-L, R IN MAIN-L, R OUT SUB1-L, R OUT
SUB2-L, R OUT LOOP OUT RHYTHM OUT PHONES OUT MASTER OUT
Value (Bold: default)
0100200
0100200 0100200 0100200 0100200 0100200
Explanation
Adjusts the input level from each input jack. Push the [1][4] knobs to mute
the sound. When STEREO LINK (p. 9) is “ON”, MIC, INST1 and INST2 are shown.
Adjusts the output level for MAIN/SUB 1/SUB 2. When STEREO LINK (p. 11) is
“ON”, MAIN, SUB1 and SUB2 are shown.
Adjusts the loop playback output level. Adjusts the rhythm sound output level.
Adjusts the PHONES output level. Adjusts the general output level for MAIN-L,
R OUT/SUB1-L, R OUT/SUB2-L, R OUT.
13
System Settings (MENU)
CTL FUNC
PANEL PLAY
9 TRACK/TRK15 9 FX/TRK15
PANEL UNDO
9 TRACK/TRK15 9 FX/TRK15
Specify the functions of the [TRACK] buttons (tracks 15). Specify the
functions of the [FX] buttons (tracks 15).
Specify the functions of the [TRACK] buttons (tracks 15) during undo/redo.
Specify the functions of the [FX] buttons (tracks 15) during undo/redo.
PUSH: HOLD: CLICK:
Functions when the button is pressed Functions when the button is held down Functions when the button is double-clicked
Value
7 OFF
– – –
7 TRK15 CLEAR
PUSH
CLEAR
7 TRK15 REVERSE
PUSH
REVERSE
7 TRK15 UNDO/REDO
PUSH
UNDO/REDO
7 TRK15 MARK BACK1
PUSH
MARK BACK
7 TRK15 MARK BACK2
PUSH
MARK BACK
HOLD
REC BACK
7 TRK15 REC BACK
PUSH
REC BACK
7 TRK15 MARK SET1
PUSH
MARK SET
7 TRK15 MARK SET2
PUSH
MARK SET
HOLD
MARK CLEAR
7 TRK15 MARK CLEAR
PUSH
MARK CLEAR
7 TRK15 HALF SPEED
PUSH
HALF SPEED
7 TRK15 HALF SPEED (MOMENT)
PUSH
HALF SPEED
14
Explanation No function is assigned. Clear the specified track. Turn reverse
play on/off for the specified track.
Undo/redo recording or the most recent overdubbing for the specified track.
Switches to the recording state set by the mark for the specified track. If a
mark has not been set, the track switches to the post-recording state.
Switches to the recording state set by the mark for the specified track. If a
mark has not been set, the track switches to the post-recording state.
Restores the specified track to how it was right after recording. Restores the
specified track to how it was right after recording. Sets a mark at the
overdubbing state for the specified track. Sets a mark at the overdubbing
state for the specified track. Deletes the mark that was set for the specified
track. Deletes the mark that was set for the specified track. Sets the
playback speed to 1/2 for the specified track. The specified track plays back
at half speed while you press the button.
System Settings (MENU)
Value
Explanation
7 TRK15 DOUBLE SPEED
PUSH
DOUBLE SPEED
Sets the playback speed to 2x for the specified track.
7 TRK15 DOUBLE SPEED (MOMENT)
PUSH
DOUBLE SPEED
The specified track plays back at double speed while you press the button.
7 TRK15 TRACK EDIT
PUSH
TRACK EDIT
Shows the TRACK screen for the specified track.
7 TRK15 TRACK FX
PUSH
FX ON/OFF
Turn the track FX on/off for the specified track.
7 CUR.TRK CLEAR
PUSH
CLEAR
Clear the currently selected track.
7 CUR.TRK REVERSE
PUSH
CLEAR
Turn reverse play on/off for the currently selected track.
7 CUR.TRK UNDO/REDO
PUSH
UNDO
Undo/redo recording or the most recent overdubbing for the currently selected track.
7 CUR.TRK MARK BACK1
PUSH
MARK BACK
Switches to the recording state set by the mark for the currently selected track. If a mark has not been set, the track switches to the post-recording state.
7 CUR.TRK MARK BACK2
PUSH
MARK BACK
Switches to the recording state set by the mark for the currently selected track. If a mark has not been set, the track switches to the post-recording state.
HOLD
REC BACK
Restores the currently selected track to how it was right after recording.
7 CUR.TRK REC BACK
PUSH
REC BACK
Restores the currently selected track to how it was right after recording.
7 CUR.TRK MARK SET1
PUSH
MARK SET
Sets a mark at the overdubbing state for the currently selected track.
7 CUR.TRK MARK SET2
PUSH
MARK SET
Sets a mark at the overdubbing state for the currently selected track.
HOLD
MARK CLEAR
Deletes the mark that was set for the currently selected track.
7 CUR.TRK MARK CLEAR
PUSH
MARK CLEAR
Deletes the mark that was set for the currently selected track.
7 CUR.TRK HALF SPEED
PUSH
HALF SPEED
Sets the playback speed to 1/2 for the currently selected track.
7 CUR.TRK HALF SPEED (MOMENT)
PUSH
HALF SPEED
The currently selected track plays back at half speed while you press the button.
7 CUR.TRK DOUBLE SPEED
PUSH
DOUBLE SPEED
Sets the playback speed to 2x for currently selected track.
7 CUR.TRK DOUBLE SPEED (MOMENT)
PUSH
DOUBLE SPEED
The currently selected track plays back at double speed while you press the button.
7 CUR.TRK TRACK EDIT
PUSH
TRACK EDIT
Shows the TRACK screen for the currently selected track.
7 CUR.TRK TRACK FX
PUSH
FX ON/OFF
Turn the track FX on/off for the currently selected track.
7 CUR.TRK INC
PUSH INC
HOLD
Switch the current track in the order of 1020…50….
7 CUR.TRK DEC
PUSH
DEC
Switch the current track in the order of 5040…10….
HOLD
INC
Switch the current track in the order of 1020…50….
7 TEMPO UP
PUSH
TEMPO DOUBLE
Doubles the tempo.
15
System Settings (MENU)
Value
7 TEMPO DOWN
PUSH
TEMPO HALF
7 INPUT FX ON/OFF
PUSH
FX ON/OFF
7 TRACK FX ON/OFF
PUSH
FX ON/OFF
7 MIC IN MUTE
PUSH
MUTE ON/OFF
7 MIC1 IN MUTE
PUSH
MUTE ON/OFF
7 MIC2 IN MUTE
PUSH
MUTE ON/OFF
7 LED
PUSH
TOGGLE COLOR
Explanation Slows the tempo down to 1/2. Turn the input FX on/off. Turn the track FX on/off. Mutes the audio from the MIC 1, 2 connectors. Mutes the audio from the MIC 1 connector. Mutes the audio from the MIC 2 connector. Switches the button’s color (when lit) to the color that was set.
16
CTL/EXP
9 CTL14
Value
7 OFF
– – –
7 TRK15 REC/PLAY1
PUSH
REC/PLAY
7 TRK15 REC/PLAY2
PUSH
REC/PLAY
HOLD
UNDO (PLAY)
7 TRK15 REC/PLAY3
PUSH
REC/PLAY
HOLD
UNDO (PLAY)
CLICK
STOP
7 TRK15 REC/PLAY4
PUSH
REC/PLAY
HOLD
UNDO, CLEAR
CLICK
STOP
7 TRK15 MOMENT PLAY
PUSH
PLAY
7 TRK15 PLAY/STOP1 Ver. 1.2
PUSH
PLAY/STOP
7 TRK15 PLAY/STOP2 Ver. 1.2
PUSH
PLAY/STOP
HOLD
UNDO (PLAY)
7 TRK15 PLAY/STOP3 Ver. 1.2
PUSH
PLAY/STOP
HOLD
UNDO, CLEAR
7 TRK15 STOP1
PUSH
STOP
7 TRK15 STOP2
PUSH
STOP
CLICK
TAP TEMPO
7 TRK15 STOP3
PUSH
STOP
HOLD
CLEAR
CLICK
TAP TEMPO
7 TRK15 STOP4
PUSH
STOP
HOLD
CLEAR
System Settings (MENU)
Specify the functions of the footswitch connected to the CTL 1, 2/EXP 1 jack
or the CTL 3, 4/EXP 2 jack. PUSH: Functions when the switch is pressed HOLD:
Functions when the switch is held down CLICK: Functions when the switch is
double-clicked Explanation
No function is assigned.
Switch between record/play/overdubbing for the specified track.
Switch between record/play/overdubbing for the specified track. The specified
track, long press the switch during playback or overdubbing to Undo, and long
press the switch once again to Redo.
Switch between record/play/overdubbing for the specified track. The specified
track, long press the switch during playback or overdubbing to Undo, and long
press the switch once again to Redo. Stop record/play for the specified track.
Switch between record/play/overdubbing for the specified track. The specified
track, long press the switch during recording or playback to Undo, and long
press the switch once again to Redo. Long press the switch during stopped, the
track is cleared. Stop record/play for the specified track.
The currently selected track plays back as long as you hold down the switch.
Switch between play/stop for the specified track.
Switch between play/stop for the specified track. The specified track, long
press the switch during playback or overdubbing to Undo, and long press the
switch once again to Redo.
Switch between play/stop for the specified track. The specified track, long
press the switch during recording or playback to Undo, and long press the
switch once again to Redo. Long press the switch during stopped, the track is
cleared.
Stop record/play for the specified track.
Stop record/play for the specified track. Sets the tempo using tap tempo.
Long-press the switch to return to the previous tempo.
Stop record/play for the specified track. Clear the specified track. Sets the
tempo using tap tempo. Long-press the switch to return to the previous tempo.
Stop record/play for the specified track. Clear the specified track.
17
System Settings (MENU)
Value
7 TRK15 STOP5
PUSH
STOP
CLICK
CLEAR
7 TRK15 CLEAR
PUSH
CLEAR
7 TRK15 REVERSE
PUSH
REVERSE
7 TRK15 UNDO/REDO
PUSH
UNDO
7 TRK15 MARK BACK1
PUSH
MARK BACK
7 TRK15 MARK BACK2
PUSH
MARK BACK
HOLD
REC BACK
7 TRK15 REC BACK
PUSH
REC BACK
7 TRK15 MARK SET1
PUSH
MARK SET
7 TRK15 MARK SET2
PUSH
MARK SET
HOLD
MARK CLEAR
7 TRK15 MARK CLEAR
PUSH
MARK CLEAR
7 TRK15 HALF SPEED
PUSH
HALF SPEED
7 TRK15 HALF SPEED (MOMENT)
PUSH
HALF SPEED
7 TRK15 DOUBLE SPEED
PUSH
DOUBLE SPEED
7 TRK15 DOUBLE SPEED (MOMENT)
PUSH
DOUBLE SPEED
7 TRK15 TRACK EDIT
PUSH
TRACK EDIT
7 TRK15 TRACK FX
PUSH
FX ON/OFF
7 CUR.TRK REC/PLAY1
PUSH
REC/PLAY
7 CUR.TRK REC/PLAY2
PUSH
REC/PLAY
HOLD
UNDO (PLAY)
7 CUR.TRK REC/PLAY3
PUSH
REC/PLAY
HOLD
UNDO (PLAY)
CLICK
STOP
Explanation
Stop record/play for the specified track. Clear the specified track.
Clear the specified track.
Turn reverse play on/off for the specified track.
Undo/redo recording or the most recent overdubbing for the specified track.
Switches to the recording state set by the mark for the specified track. If a
mark has not been set, the track switches to the post-recording state.
Switches to the recording state set by the mark for the specified track. If a
mark has not been set, the track switches to the post-recording state.
Restores the specified track to how it was right after recording.
Restores the specified track to how it was right after recording.
Sets a mark at the overdubbing state for the specified track.
Sets a mark at the overdubbing state for the specified track. Deletes the mark
that was set for the specified track.
Deletes the mark that was set for the specified track.
Sets the playback speed to 1/2 for the specified track.
The specified track plays back at half speed while you press the button.
Sets the playback speed to 2x for the specified track.
The specified track plays back at double speed while you press the button.
Shows the TRACK screen for the specified track.
Turn the track FX on/off for the specified track.
Switch between record/play/overdubbing for the currently selected track.
Switch between record/play/overdubbing for the currently selected track. The
specified track, long press the switch during playback or overdubbing to Undo,
and long press the switch once again to Redo.
Switch between record/play/overdubbing for the currently selected track. The
specified track, long press the switch during playback or overdubbing to Undo,
and long press the switch once again to Redo. Stop record/play for the
currently selected track.
18
Value
7 CUR.TRK REC/PLAY4
PUSH
REC/PLAY
HOLD
UNDO, CLEAR
CLICK
STOP
7 CUR.TRK MOMENT PLAY
PUSH
PLAY
7 CUR.TRK PLAY/STOP1 Ver. 1.2
PUSH
PLAY/STOP
7 CUR.TRK PLAY/STOP2 Ver. 1.2
PUSH
PLAY/STOP
HOLD
UNDO (PLAY)
7 CUR.TRK PLAY/STOP3 Ver. 1.2
PUSH
PLAY/STOP
HOLD
UNDO, CLEAR
7 CUR.TRK STOP1
PUSH
STOP
7 CUR.TRK STOP2
PUSH
STOP
CLICK
TAP TEMPO
7 CUR.TRK STOP3
PUSH
STOP
HOLD
CLEAR
CLICK
TAP TEMPO
7 CUR.TRK STOP4
PUSH
STOP
HOLD
CLEAR
7 CUR.TRK STOP5
PUSH
STOP
CLICK
CLEAR
7 CUR.TRK CLEAR
PUSH
CLEAR
7 CUR.TRK REVERSE
PUSH
REVERSE
7 CUR.TRK UNDO/REDO
PUSH
UNDO
7 CUR.TRK MARK BACK1
PUSH
MARK BACK
7 CUR.TRK MARK BACK2
PUSH
MARK BACK
HOLD
REC BACK
7 CUR.TRK REC BACK
PUSH
REC BACK
System Settings (MENU)
Explanation
Switch between record/play/overdubbing for the currently selected track. The
specified track, long press the switch during recording or playback to Undo,
and long press the switch once again to Redo. Long press the switch during
stopped, the track is cleared. Stop record/play for the currently selected
track.
The currently selected track plays back as long as you hold down the switch.
Switch between play/stop for the currently selected track.
Switch between play/stop for the currently selected track. The specified
track, long press the switch during playback or overdubbing to Undo, and long
press the switch once again to Redo.
Switch between play/stop for the currently selected track. The currently
selected track, long press the switch during recording or playback to Undo,
and long press the switch once again to Redo. Long press the switch during
stopped, the track is cleared.
Stop record/play for the currently selected track.
Stop record/play for the currently selected track. Sets the tempo using tap
tempo. Long-press the switch to return to the previous tempo.
Stop record/play for the currently selected track. Clear the currently
selected track. Sets the tempo using tap tempo. Long-press the switch to
return to the previous tempo.
Stop record/play for the currently selected track. Clear the specified track.
Stop record/play for the currently selected track. Clear the currently
selected track.
Clear the currently selected track.
Turn reverse play on/off for the currently selected track.
Undo/redo recording or the most recent overdubbing for the currently selected
track.
Switches to the recording state set by the mark for the currently selected
track. If a mark has not been set, the track switches to the post-recording
state.
Switches to the recording state set by the mark for the currently selected
track. If a mark has not been set, the track switches to the post-recording
state. Restores the currently selected track to how it was right after
recording.
Restores the currently selected track to how it was right after recording.
19
System Settings (MENU)
Value
Explanation
7 CUR.TRK MARK SET1
PUSH
MARK SET
Sets a mark at the overdubbing state for the currently selected track.
7 CUR.TRK MARK SET2
PUSH
MARK SET
Sets a mark at the overdubbing state for the currently selected track.
HOLD
MARK CLEAR
Deletes the mark that was set for the currently selected track.
7 CUR.TRK MARK CLEAR
PUSH
MARK CLEAR
Deletes the mark that was set for the currently selected track.
7 CUR.TRK HALF SPEED
PUSH
HALF SPEED
Sets the playback speed to 1/2 for the currently selected track.
7 CUR.TRK HALF SPEED (MOMENT)
PUSH
HALF SPEED
The currently selected track plays back at half speed while you press the button.
7 CUR.TRK DOUBLE SPEED
PUSH
DOUBLE SPEED
Sets the playback speed to 2x for currently selected track.
7 CUR.TRK DOUBLE SPEED (MOMENT)
PUSH
DOUBLE SPEED
The currently selected track plays back at double speed while you press the button.
7 CUR.TRK TRACK EDIT
PUSH
TRACK EDIT
Shows the TRACK screen for the currently selected track.
7 CUR.TRK TRACK FX
PUSH
FX ON/OFF
Turn the track FX on/off for the currently selected track.
7 CUR.TRK INC1
PUSH INC
HOLD
Switch the current track in the order of 1020…50….
7 CUR.TRK INC2
PUSH
INC
Switch the current track in the order of 1020…50….
HOLD
DEC
Switch the current track in the order of 5040…10….
7 CUR.TRK DEC1
PUSH DEC
HOLD
Switch the current track in the order of 5040…10….
7 CUR.TRK DEC2
PUSH
DEC
Switch the current track in the order of 5040…10….
HOLD
INC
Switch the current track in the order of 1020…50….
7 CUR.TRK NUM
PUSH
– – –
Sets the current track.
7 ALL START/STOP1
PUSH
ALL START/STOP
Makes all tracks start (play back) at the same time. If you press the switch
when the tracks are currently playing back or recording, all tracks stop. * If
START MODE/STOP MODE (p. 2) is set to “FADE”, playback starts or stops after
the fade-in or
fade-out.
7 ALL START/STOP2
PUSH
ALL START/STOP
Makes all tracks start (play back) at the same time. If you press the switch
when the tracks are currently playing back or recording, all tracks stop. * If
START MODE/STOP MODE (p. 2) is set to “FADE”, playback starts or stops after
the fade-in or
fade-out.
HOLD
ALL CLEAR
Clears all tracks.
7 ALL START/STOP3
PUSH
ALL START/STP
Makes all tracks start (play back) at the same time. If you press the switch
when the tracks are currently playing back or recording, all tracks stop. * If
START MODE/STOP MODE (p. 2) is set to “FADE”, playback starts or stops after
the fade-in or
fade-out.
CLICK
ALL CLEAR
Clears all tracks.
20
Value 7 ALL START/STOP4 Ver. 1.2
PUSH
IMM ALL ST/STOP
7 ALL START/STOP5 Ver. 1.2
PUSH
IMM ALL ST/STOP
HOLD
ALL CLEAR
7 ALL START/STOP6 Ver. 1.2
PUSH
IMM ALL ST/STOP
CLICK
ALL CLEAR
7 ALL CLEAR1 Ver. 1.2
PUSH
ALL CLEAR
7 ALL CLEAR2 Ver. 1.2
HOLD
ALL CLEAR
7 TAP TEMPO
PUSH
TAP TEMPO
HOLD
TEMPO REVERT
7 TEMPO UP
PUSH
TEMPO DOUBLE
7 TEMPO DOWN
PUSH
TEMPO HALF
7 INPUT FX
PUSH
FX ON/OFF
7 INPUT FX AD
PUSH
FX ON/OFF
7 INPUT FX CUR
PUSH
FX ON/OFF
7 TRACK FX
PUSH
FX ON/OFF
7 TRACK FX AD
PUSH
FX ON/OFF
7 TRACK FX CUR
PUSH
FX ON/OFF
7 RHYTHM START/STOP
PUSH
RHY START/STOP
7 RHYTHM START
PUSH
RHYTHM START
7 RHYTHM STOP
PUSH
RHYTHM STOP
7 MEMORY INC1
PUSH INC
HOLD
7 MEMORY INC2 Ver. 1.2
PUSH
INC
HOLD
DEC
System Settings (MENU)
Explanation
Makes all tracks start (play back) at the same time. If you press the switch
when the tracks are currently playing back or recording, all tracks stop.
Even if START MODE/STOP MODE (p. 2) is set to “FADE”, playback starts/stops
immediately.
Makes all tracks start (play back) at the same time. If you press the switch
when the tracks are currently playing back or recording, all tracks stop.
Even if START MODE/STOP MODE (p. 2) is set to “FADE”, playback starts/stops
immediately. Clears all tracks.
Makes all tracks start (play back) at the same time. If you press the switch
when the tracks are currently playing back or recording, all tracks stop. *
Even if START MODE/STOP MODE (p. 2) is set to “FADE”, playback starts/stops
immediately. Clears all tracks.
Clears all tracks.
Clears all tracks.
Sets the tempo using tap tempo. Long-press the switch to return to the
previous tempo. Returns the tempo to its previous value before editing.
Doubles the tempo.
Slows the tempo down to 1/2.
Turn the input FX on/off.
Turn the input FX AD on/off for the currently selected FX bank.
Turn the input FX on/off for the currently selected.
Turn the track FX on/off.
Turn the track FX AD on/off for the currently selected FX bank.
Turn the track FX on/off for the currently selected.
Switch the rhythm between start/stop.
Start playing the rhythm.
Stop playing the rhythm.
Switch the memory in the order of 010020…990….
Switch the memory in the order of 010020…990…. Switch the memory in the order
of 990980…010….
21
System Settings (MENU)
Value
7 MEMORY DEC1
PUSH DEC
HOLD
7 MEMORY DEC2 Ver. 1.2
PUSH
DEC
HOLD
INC
7 MEMORY WRITE
PUSH
WRITE
7 MIC IN MUTE
PUSH
MUTE ON/OFF
7 MIC1 IN MUTE
PUSH
MUTE ON/OFF
7 MIC2 IN MUTE
PUSH
MUTE ON/OFF
Explanation
Switch the memory in the order of 990980…010….
Switch the memory in the order of 990980…010…. Switch the memory in the order
of 010020…990…. Writes the settings in the currently selected memory. Mute the
audio from the MIC 1, 2 connectors. Mute the audio from the MIC 1 connector.
Mute the audio from the MIC 2 connector.
22
9 EXP1, 2 Parameter
FUNC
MIN MAX
Value (Bold: default) OFF TRK15 LEVEL1
TRK15 LEVEL2
CUR.TRK LEVEL1 CUR.TRK LEVEL2 TEMPO UP TEMPO DOWN IN FX AD CTL IN FX CUR CTL
(EXP1) TR FX AD CTL TR FX CUR CTL (EXP2) RHYTHM LEVEL1 RHYTHM LEVEL2
0255
System Settings (MENU)
Specify the functions of an expression pedal connected to the CTL 1, 2/EXP 1
jack or the CTL 3, 4/EXP 2 jack.
Explanation No function is assigned. Control the “PLAY LEVEL” (p. 2) of the
specified track in the range of 0200. Control the level of the specified
track in the range of 0”maximum value”, with the “PLAY LEVEL” setting of the
currently selected track as the maximum value. Control the “PLAY LEVEL” of the
currently selected track in the range of 0200. Control the level of the
currently selected track in the range of 0”maximum value”, with the “PLAY
LEVEL” setting of the currently selected track as the maximum value. Press the
pedal to make the tempo faster. Press the pedal to make the tempo slower.
Controls the intensity of input FX AD in the currently selected FX bank.
Controls the intensity of the currently selected input FX. Controls the
intensity of track FX AD in the currently selected FX bank. Controls the
intensity of the currently selected track FX. Control the “RHYTHM OUT” (p. 13)
of MIXER in the range of 0200. Control the level in the range of 0”maximum
value”, with the “RHYTHM OUT” setting of MIXER as the maximum value. Specifies
the variable range of the function that is specified. The value (MIN: minimum
value, MAX: maximum value) depends on the function that is specified.
PREFERENCE
Parameter MODE PLAY MODE UNDO QUICK CLEAR ALL CLEAR CTL14 EXP1, 2
Value (Bold: default) SYSTEM, MEMORY SYSTEM, MEMORY OFF, ON OFF, ON SYSTEM, MEMORY SYSTEM, MEMORY
Explanation
Selects whether to switch the “PANEL PLAY” (p. 14) settings to either the
settings for each memory (5) or to the system settings.
Selects whether to switch the “PANEL UNDO” (p. 14) settings to either the
settings for each memory (5) or to the system settings.
Turns the QUICK CLEAR function on/off. The QUICK CLEAR function clears all
track when you double-click the [9] button.
Turns the ALL CLEAR function on/off. The ALL CLEAR function clears all tracks
when you long-press the [ALL START/STOP] button.
Selects whether to switch the CTL/EXP “CTL1″”CTL4” (p. 17) settings to either
the settings for each memory (5) or to the system settings.
Selects whether to switch the CTL/EXP “EXP1″”EXP2” (p. 23) settings to either
the settings for each memory (5) or to the system settings.
(*5) When switching to the settings for each memory, use the write operation to save the settings to memory.
23
System Settings (MENU)
ASSIGN
NOTE
The ASSIGN settings are stored in memory. Execute the write operation to save these settings to each memory.
ASSIGN116
Parameter SW
SOURCE
SOURCE MODE SOURCE ACT. LO SOURCE ACT. HI
TARGET
Value (Bold: default) OFF, ON
Explanation Specifies whether assignments will be used (ON/OFF).
Specify the controller (source) that will control the target.
TRK15 REC/DB
When the specified track switches from playback/stop to recording/overdubbing
TRK15 PLY/STP
When the specified track switches from recording/overdubbing to playback/stop
SYNC ST/STP
All Start/Stop message from an external MIDI device
TRK15 FX (PLY)
The [FX] button for the specified track
TRK15 TR (PLY)
The [TRACK] button for the specified track
TRK15 FX (UND)
The [FX] button for the specified track during undo/redo
TRK15 TR (UND)
The [TRACK] button for the specified track during undo/redo
IN FX KNOB
[INPUT FX] knob
TR FX KNOB
[TRACK FX] knob
CTL1, 2
A footswitch (CTL1, CTL2) connected to the CTL 1, 2/EXP jack
CTL3, 4
A footswitch (CTL3, CTL4) connected to the CTL 3, 4/EXP jack
EXP1
An Expression pedal (EXP1) connected to the CTL 1, 2/EXP jack
EXP2
An Expression pedal (EXP2) connected to the CTL 3, 4/EXP jack
MIDI CC#0131 MIDI CC#6495
Control Change message (131, 6495) from an external MIDI device
If a momentary-type footswitch (such as the separately sold FS-5U) is connected as the source, you can specify how footswitch operations will affect the value.
MOMENT
The setting will normally be off (minimum value); it will be on (maximum value) only while you continue holding down the footswitch.
TOGGLE
The setting will alternate between off (minimum value) and on (maximum value) each time you press the footswitch.
0127
Specifies the controllable range for target parameters within the source’s operational range. Target parameters are controlled within the range set with ACT LOW and ACT HIGH. You should normally set ACT LOW to “0” and ACT HIGH to “127”.
Specifies the function that is controlled. * Depending on the specified function, control might not be possible while playing a track or the rhythm.
TRK15 REC/PLY
Switch between record/play/overdubbing for the specified track.
TRK15 PLY/STP
Switch between play/stop for the specified track.
TRK15 STOP
Stop record/play for the specified track.
TRK15 CLEAR
Clear the specified track.
TRK15 REVERSE
Turn reverse play on/off for the specified track.
TRK15 UN/RED
Undo/redo recording or the most recent overdubbing for the specified track.
TRK15 M.BACK
Switches to the recording state set by the mark for the specified track. If a mark has not been set, the track switches to the post-recording state.
TRK15 R.BACK
Restores the specified track to how it was right after recording.
TRK15 M.SET
Sets a mark at the overdubbing state for the specified track.
TRK15 M.CLEAR
Deletes the mark that was set for the specified track.
TRK15 LEVEL
Control the “PLAY LEVEL” (p. 2) of the specified track in the range of 0200.
CUR.TRK REC/PLY
Switch between record/play/overdubbing for the currently selected track.
CUR.TRK PLY/STP
Switch between play/stop for the currently selected track.
CUR.TRK STOP
Stop record/play for the currently selected track.
CUR.TRK CLEAR
Clear the currently selected track.
24
Parameter TARGET
Value (Bold: default) CUR.TRK REVERSE CUR.TRK UN/RED CUR.TRK M.BACK CUR.TRK
R.BACK CUR.TRK M.SET CUR.TRK M.CLEAR CUR.TRK LEVEL CUR.TRK INC CUR.TRK DEC
CUR.TRK NUM
ALL ST/STP
TAP TEMPO TEMPO INPUT FX IN FX TGT INC
IN FX TGT DEC IN FX BNK INC IN FX BNK DEC IN FX SW MODE IN FX AD IN FX AD
CTL IN FX AD TYPE IN FX AD TYP INC
IN FX AD TYP DEC
IN FX AD SW MODE IN FX AD PRM14 IN FX AD SEQ IN FX AD S.SYNC IN FX AD
S.RTRIG IN FX AD S.RATE IN FX AD S.MAX IN FX AADD IN FX AADD CTL IN FX
AADD TYPE IN FX AADD TYP INC IN FX AADD TYP DEC IN FX AADD SW MODE IN FX
AADD PRM14 IN FX AADD SEQ IN FX AADD S.SYNC IN FX AADD S.RTRIG
System Settings (MENU)
Explanation Turn reverse play on/off for the currently selected track.
Undo/redo recording or the most recent overdubbing for the currently selected
track. Switches to the recording state set by the mark for the currently
selected track. If a mark has not been set, the track switches to the post-
recording state. Restores the currently selected track to how it was right
after recording. Sets a mark at the overdubbing state for the currently
selected track. Deletes the mark that was set for the currently selected
track. Control the “PLAY LEVEL” (p. 2) of the currently selected track in the
range of 0200. Switch the current track in the order of 1020…50…. Switch the
current track in the order of 5040…10…. Sets the current track. Makes all
tracks start (play back) at the same time. If you press the switch when the
tracks are currently playing back or recording, all tracks stop. Sets the
tempo using tap tempo. Long-press the switch to return to the previous tempo.
Controls the tempo. Turn the input FX on/off. Use the [INPUT FX] knob to
switch the input FX in order from A0D for the currently selected FX bank. Use
the [INPUT FX] knob to switch the input FX in order from D0A for the currently
selected FX bank. Switches the FX bank of the input FX in order from A0D.
Switches the FX bank of the input FX in order from D0A. Switches the INPUT FX
[A][D] button operations (TOGGLE/MOMENT: p. 5) all at once for the currently
selected FX bank. Turn the input FX AD on/off for the currently selected FX
bank. Controls the parameters according to the input FX AD type for the
currently selected FX bank. Switches the input FX AD type for the currently
selected FX bank. Switches the input FX AD type in order from “LPF”0″REVERSE
REVERB” for the currently selected FX bank. Switches the input FX AD type in
order from “REVERSE REVERB”0″LPF” for the currently selected FX bank. Switches
the input FX [A][D] button operations (TOGGLE/MOMENT) for the currently
selected FX bank. Controls the input FX AD parameters 14 for the currently
selected FX bank. Turns the input FX AD FX sequence function (p. 34) on/off
for the currently selected FX bank. Controls the input FX AD “SYNC” for the
currently selected FX bank. Controls the input FX AD “RTRIG” for the
currently selected FX bank. Controls the input FX AD “STEP RATE” for the
currently selected FX bank. Controls the input FX AD “STEP MAX” for the
currently selected FX bank. Turn the input FX A-A through D-D on/off. Controls
the parameters according to the input FX A-A through D-D type. Switches the
input FX A-A through D-D type. Switches the input FX A-A through D-D type in
order from “LPF”0″REVERSE REVERB”. Switches the input FX A-A through D-D type
in order from “REVERSE REVERB”0″LPF”. Switches the INPUT FX [A][D] button
operations (TOGGLE/MOMENT) for input FX A-A through D-D. Controls the input FX
A-A through D-D parameters 14. Turns the input FX A-A through D-D FX sequence
function (p. 34) on/off. Controls the input FX A-A through D-D “SYNC”.
Controls the input FX A-A through D-D “RTRIG”.
25
System Settings (MENU)
Parameter TARGET
26
Value (Bold: default) IN FX AADD S.RATE IN FX AADD S.MAX IN FX CR IN FX CR
CTL IN FX CR TYPE IN FX CR TYP INC
IN FX CR TYP DEC
IN FX CR SW MODE IN FX CUR PRM14 IN FX CUR SEQ IN FX CUR S.SYNC IN FX CUR
S.RTRIG IN FX CUR S.RATE IN FX CUR S.MAX TRK FX TRK FX TGT INC
TRK FX TGT DEC
TRK FX BNK INC TRK FX BNK DEC TRK FX SW MODE T FX AD T FX AD CTL T FX AD
TYPE T FX AD TYP INC
T FX AD TYP DEC
T FX AD SW MODE T FX AD PRM14 T FX AD SEQ T FX AD S.SYNC T FX AD S.RTRIG
T FX AD S.RATE T FX AD S.MAX T FX AADD T FX AADD CTL T FX AADD TYPE T FX
AADD TYP INC T FX AADD TYP DEC T FX AADD SW MODE T FX AADD PRM14 T FX
AADD SEQ T FX AADD S.SYNC T FX AADD S.RTRIG
Explanation Controls the input FX A-A through D-D “STEP RATE”. Controls the input FX A-A through D-D “STEP MAX”. Turn the input FX on/off for the currently selected. Controls the parameters according to the currently selected input FX type. Switches the type of the currently selected input FX. Switches the type of the currently selected input FX in order from “LPF”0″REVERSE REVERB”. Switches the type of the currently selected input FX in order from “REVERSE REVERB”0 “LPF”. Switches the operations (TOGGLE/MOMENT: p. 5) of the currently selected button for the INPUT FX [A][D] buttons. Controls parameters 14 of the currently selected input FX. Turns the FX sequence function (p. 34) on/off for the currently selected input FX AD. Controls the “SYNC” for the currently selected input FX AD. Controls the “RTRIG” for the currently selected input FX AD. Controls the “STEP RATE” for the currently selected input FX AD. Controls the “STEP MAX” for the currently selected input FX AD. Turn the track FX on/off. Use the [TRACK FX] knob to switch the track FX in order from A0D for the currently selected FX bank. Use the [TRACK FX] knob to switch the track FX in order from D0A for the currently selected FX bank. Switches the FX bank of the track FX in order from A0D. Switches the FX bank of the track FX in order from D0A. Switches the TRACK FX [A][D] button operations (TOGGLE/MOMENT: p. 6) all at once for the currently selected FX bank. Turn the track FX AD on/off for the currently selected FX bank. Controls the parameters according to the track FX AD type for the currently selected FX bank. Switches the track FX AD type for the currently selected FX bank. Switches the track FX AD type in order from “LPF”0″VINYL FLICK” for the currently selected FX bank. Switches the track FX AD type in order from “VINYL FLICK”0″LPF” for the currently selected FX bank. Switches the track FX [A][D] button operations (TOGGLE/MOMENT) for the currently selected FX bank. Controls the track FX AD parameters 14 for the currently selected FX bank. Turns the track FX AD FX sequence function (p. 34) on/off for the currently selected FX bank. Controls the track FX AD “SYNC” for the currently selected FX bank. Controls the track FX AD “RTRIG” for the currently selected FX bank. Controls the track FX AD “STEP RATE” for the currently selected FX bank. Controls the track FX AD “STEP MAX” for the currently selected FX bank. Turn the track FX A-A through D-D on/off. Controls the parameters according to the track FX A-A through D-D type. Switches the track FX A-A through D-D type. Switches the track FX A-A through D-D type in order from “LPF”0″VINYL FLICK”. Switches the track FX A-A through D-D type in order from “VINYL FLICK”0″LPF”. Switches the TRACK FX [A][D] button operations (TOGGLE/MOMENT) for track FX A-A through D-D. Controls the track FX A-A through D-D parameters 14. Turns the track FX A-A through D-D FX sequence function (p. 34) on/off. Controls the track FX A-A through D-D “SYNC”. Controls the track FX A-A through D-D “RTRIG”.
Parameter TARGET
Value (Bold: default) T FX AADD S.RATE T FX AADD S.MAX T FX CR T FX CR CTL T
FX CR TYPE T FX CR TYP INC T FX CR TYP DEC
T FX CR SW MODE
T FX CUR PRM14 T FX CUR SEQ T FX CUR S.SYNC T FX CUR S.RTRIG T FX CUR S.RATE
T FX CUR S.MAX RHYTHM ST/STP RHYTHM START RHYTHM STOP RHYTHM LEVEL MIC IN MUTE
MIC1 IN MUTE MIC2 IN MUTE TRK 15 FADER TRK 15 1SHOT TRK 15 PAN TRK 15 FX
TRK 15 SPEED TRK 15 BNC IN DUB MODE AUTO REC BOUNCE RHYTHM VARI RHYTHM KIT
MIC 1, 2 LEVEL INST1-L, R LEVE (6) INST1-L, R MUTE (6) INST2-L, R LEVEL (6)
INST2-L, R MUTE (6) LOOP LEVEL MAIN-L, R LEVEL (6) SUB1-L, R LEVEL (6)
SUB2-L, R LEVEL (6) PHONES LEVEL
MASTER LEVEL
INST1, 2 GAIN EQ MIC1, 2 EQ INST-1L, R (6) EQ INST-2L, R (*6) INPUT THRU
System Settings (MENU)
Explanation Controls the track FX A-A through D-D “STEP RATE”. Controls the
track FX A-A through D-D “STEP MAX”. Turn the track FX on/off for the
currently selected. Controls the parameters according to the currently
selected track FX type. Switches the type of the currently selected track FX.
Switches the type of the currently selected track FX in order from
“LPF”0″VINYL FLICK”. Switches the type of the currently selected track FX in
order from “VINYL FLICK”0″LPF”. Switches the operations (TOGGLE/MOMENT: p. 6)
of the currently selected button for the TRACK FX [A][D] buttons. Controls
parameters 14 of the currently selected track FX. Turns the FX sequence
function (p. 34) on/off for the currently selected track FX AD. Controls the
“SYNC” for the currently selected track FX AD. Controls the “RTRIG” for the
currently selected track FX AD. Controls the “STEP RATE” for the currently
selected track FX AD. Controls the “STEP MAX” for the currently selected
track FX AD. Switch the rhythm between start/stop. Start playing the rhythm.
Stop playing the rhythm. Control “RHYTHM OUT” (p. 13) of MIXER in the range of
0200. Mute the audio from the MIC 1, 2 connectors. Mute the audio from the
MIC 1 connector. Mute the audio from the MIC 2 connectors. Control the volume
of the currently selected track. Control “1SHOT” for the currently selected
track. Control “PAN” for the currently selected track. Control the effects
(input FX/track FX) of the currently selected track. Control the SYNC “SPEED”
(p. 3) for the currently selected track. Turns bounce recording on/off for the
specified track. Control “DUB MODE” (p. 2). Turns auto recording on/off. Turns
bounce recording on/off. Switch the rhythm pattern variation. Switch the drum
kit. Controls the MIC 1, 2 input level. Controls the INST 1 input level. Mutes
the INST 1 input. Controls the INST 2 input level. Mutes the INST 2 input.
Adjusts the loop playback output level. Controls the MAIN output level.
Controls the SUB 1 output level. Controls the SUB 2 output level. Controls the
PHONES output level. Used for overall control of the output levels for MAIN-L,
R OUT, SUB 1-L, R OUT and SUB 2-L, R OUT. Controls “INST 1 GAIN” and “INST 2
GAIN” (p. 9). Turns the equalizer on/off for MIC 1, 2. Turns the equalizer
on/off for INST 1. Turns the equalizer on/off for INST 2. Controls the “INPUT
THRU” (p. 12) for INPUT/RHYTHM in OUTPUT/ROUTING.
27
System Settings (MENU)
Parameter
TARGET
TARGET MIN TARGET MAX
Value (Bold: default)
Explanation
EQ MAIN-L, R (*6)
Turns the equalizer on/off for MAIN.
EQ SUB1-L, R (*6)
Turns the equalizer on/off for SUB 1.
EQ SUB2-L, R (*6)
Turns the equalizer on/off for SUB 2.
PANEL MODE
Switches between “PANEL PLAY” and “PANEL UNDO” (p. 14) for CTL FUNC.
MIDI CC#0131 MIDI CC#64127
Transmit a control change message of the specified controller number from the MIDI OUT connector.
Specifies the variable range of the function (parameter) that is specified as the target. The value (MIN: minimum value, MAX: maximum value) depends on the parameter that is specified as the target.
(*6) When STEREO LINK (p. 9, p. 11) is “ON”, the function set for the L side is enabled.
USB
Parameter STORAGE
MODE AUDIO
ROUTING INPUT LEVEL OUTPUT LEVEL
Value (Bold: default)
Explanation
OFF, CONNECT
Change this from the OFF setting when connecting the RC-505mk2 via USB to your
computer.
When a connection with the computer is established, the message “CONNECTING…”
appears.
These are the settings for the USB driver when USB audio is used.
GENERIC
Choose this if you want to use the generic USB driver provided by your computer’s operating system.
VENDOR
Choose this if you want to use a USB driver downloaded from the BOSS website. In order to use the RC-505mk2 with the “VENDOR” setting, you must download the driver from the following URL and install it on your computer. For details on installation, refer to the following URL.
&https://www.boss.info/support/
These parameters set the output destination for the audio signal that’s inputted to the USB port of the RC-505mk2 from your computer.
LINE OUT
Outputs the audio signal from the MAIN jacks (L/MONO, R) and PHONES jack (*7).
SUB MIX
Outputs the audio signal from the MAIN jacks (L/MONO, R) and PHONES jack (*7), as well as the signal from the USB port of the RC-505mk2 to your computer.
LOOP IN
The audio signal is input to each track. You can also record this audio.
0100200
Sets the output level of the audio signal inputted to the USB port of the RC- 505mk2 from your computer.
0100200
Sets the output level of the audio signal outputted from the RC-505mk2’s USB port to your computer.
(*7) Audio is not output from the PHONES jack when PHONES OUT (p. 12) is set to “INDIVIDUAL”.
28
System Settings (MENU)
MIDI
Parameter CTL
RX CH RHYTHM VOICE
TX CH
CLOCK SYNC
OUT START
PC OUT
THRU
MIDI IN USB IN
Value (Bold: default)
Explanation
116
Specifies the receive channel for messages (control changes) that switch memories or control the RC-505mk2.
11016
Specifies the receive channel for note messages that play the rhythm.
116
Sets the channel for receiving note messages used by the HARMONIST and VOCODER effects.
116, RX CTL
Specifies the MIDI transmit channel. If this is “RX CTL”, the channel will be the same as the RX CTL CH.
Specifies the input to which the tempo clock is synchronized.
AUTO
The RC-505mk2 will normally operate using its internal tempo, but will
synchronize the tempo to MIDI clock if MIDI clock data is being input via the
MIDI IN connector or the USB port. Choose the “AUTO” setting if using the RC-
505mk2 as a remote device.
The priority order is MIDI>USB>internal clock.
INTERNAL
The clock uses the tempo specified by the memory.
Choose the “INTERNAL” setting if you don’t want to synchronize the RC-505mk2
to an external device.
MIDI
Synchronize to the tempo from the MIDI IN connector.
USB (AUTO)
Synchronize to the tempo from the USB port.
OFF, ON
Specifies whether MIDI clock is transmitted (ON) or not transmitted (OFF).
Specifies what starts in synchronization when a MIDI start message is received.
OFF
Synchronized start does not occur.
ALL
Track + rhythm
RHYTHM
Rhythm
OFF, ON
Specifies whether program change messages are transmitted (ON) or not transmitted (OFF).
Specifies the connector(s) from which MIDI messages received at the MIDI IN connector or the USB port are output.
OFF
MIDI messages are not output.
MIDI OUT
Output from the MIDI OUT connector.
USB OUT
Output from the USB port.
USB & MIDI
Output from the USB port and the MIDI OUT connector.
29
System Settings (MENU)
SETUP
Parameter CONTRAST DISPLAY MODE INDICATOR FX KNOB MODE AUTO OFF
MIN MEMORY EXT
MAX
KNOB FUNC 14
Value (Bold: default)
Explanation
1510
Adjusts the display contrast.
Specifies the play screen that will be immediately after start-up.
MEMORY NUMBER LOOP LEVEL
TRACK STATUS INPUT FX
LOOP TRACKS TRACK FX
LOOP STATUS
Specifies how the loop indicators will be shown. Stopped
(No phrase)
Stopped
(Phrase exists)
Recording Overdubbing
Playback
STATUS
LOOP POSITION LEVEL
Status indication
Loop position Playback level
Unlit
lit Unlit
Blink (tempo)
Loop position (one-measure)
Loop position
Playback level
IMMEDIATE, HOOK
When you move a [INPUT FX] knob or [TRACK FX] knob, this setting specifies whether control data for that knob position is always output (IMMEDIATE) or is output only after the knob position has passed through the current value of the parameter (HOOK).
OFF, ON
Turns the Auto Off function on/off.
If this is “ON”, the power will turn off automatically when 10 hours have
passed since you last played or operated the unit.
0199 0199
Specify the extent in which memories can be switched (lower limit: MIN / upper limit: MAX).
These parameters set the functions of the [1][4] knobs when the play screen is shown.
OFF (2, 3) MEMORY (1)
No function is assigned. Switch the memories.
TRK 15 REVERSE
Control “REVERSE” (p. 2) for the specified track.
TRK 15 1SHOT
Control “1SHOT” for the specified track.
TRK 15 PAN
Control “PAN” for the specified track.
TRK 15 LEVEL
Control “PLAY LEVEL” for the specified track.
TRK 15 DUB
Control “DUB MODE” for the specified track.
TRK 15 FX
Control the effects (input FX/track FX) of the specified track.
TRK 15 BNC IN
Turns bounce recording on/off the specified track.
DUB MODE
Control “DUB MODE”.
AUTO REC
Turns auto recording on/off.
BOUNCE
Turns bounce recording on/off.
CURRENT TRACK
Switch the current track.
FD TIME IN
Control the FADE TIME “IN”.
FD TIME OUT
Control the FADE TIME “OUT”.
IN FX AD SW
Turn the input FX AD on/off for the currently selected FX bank.
IN FX AD TYPE
Switches the input FX AD type for the currently selected FX bank.
IN FX AD PRM14
Controls the input FX AD parameters 14 for the currently selected FX bank.
IN FX AD SW MODE
Switches the INPUT FX [A][D] button operations (TOGGLE/MOMENT: p. 5) for the currently selected FX bank.
IN FX BANK
Switches the FX bank of the input FX
IN FX MODE
Control “MODE” (p. 5) of input FX.
IN FX SW
Turn the input FX on/off.
IN FX TARGET
Switches the input FX controlled by the [INPUT FX] knob for the currently selected FX bank.
IN FX SW MODE
Switches the INPUT FX [A][D] button operations (TOGGLE/MOMENT: p. 5) all at once for the currently selected FX bank.
TR FX AD SW
Turn the track FX AD on/off for the currently selected FX bank.
TR FX AD TYPE
Switches the track FX AD type for the currently selected FX bank.
TR FX AD PRM14
Controls the track FX AD parameters 14 for the currently selected FX bank.
30
Parameter KNOB FUNC 14
Value (Bold: default)
TR FX AD SW MODE
TR FX BANK TR FX MODE TR FX SW TR FX TARGET
TR FX SW MODE
RHYTHM LEVEL RHYTHM VARI RHYTHM KIT RHYTHM R.INTRO RHYTHM P.INTRO RHYTHM
ENDING MIC1, 2 LEVEL MIC1, 2 MUTE INST1, 2 LEVEL INST1, 2 MUTE INST1(R), 2(R)
LEVEL INST1(R), 2(R) MUTE LOOP LEVEL RHYTHM LEVEL MAIN LEVEL MAIN(R) LEVEL
SUB1, 2 LEVEL SUB1(R), 2(R) LEVEL PHONES LEVEL MASTER LEVEL INST 1, 2 GAIN
MIC1, 2 EQ SW MIC1, 2 EQ LO G MIC1, 2 EQ HI G MIC1, 2 EQ LM F MIC1, 2 EQ LM Q
MIC1, 2 EQ LM G MIC1, 2 EQ HM F MIC1, 2 EQ HM Q MIC1, 2 EQ HM G MIC1, 2 EQ LVL
MIC1, 2 EQ LO C MIC1, 2 EQ HI C INST1-L, R EQ SW
System Settings (MENU)
Explanation Switches the TRACK FX [A][D] button operations (TOGGLE/MOMENT: p.
6) for the currently selected FX bank. Switches the FX bank of the track FX
Control “MODE” (p. 6) of track FX. Turn the track FX on/off. Switches the
track FX controlled by the [TRACK FX] knob for the currently selected FX bank.
Switches the TRACK FX [A][D] button operations (TOGGLE/MOMENT) all at once
for the currently selected FX bank. Adjusts the volume of the rhythm. Switch
the rhythm pattern variation. Switch the drum kit. Control “INTRO REC” (p. 7)
of rhythm. Control “INTRO PLAY” of rhythm. Control “ENDING” of rhythm.
Controls the MIC 1, 2 input level. Turn the mute on/off of the MIC 1, 2.
Controls the INST 1, 2 input level. Turn the mute on/off of the INST 1, 2.
Controls the INST 1 R, 2 R input level. Turn the mute on/off of the INST 1 R,
2 R. Controls the loop playback output level. Controls the rhythm sound output
level. Controls the MAIN output level. Controls the MAIN R output level.
Controls the SUB 1, 2 output level. Controls the SUB 1 R, 2 R output level.
Controls the PHONES output level. Controls the general output level for
MAIN-L, R OUT/SUB1-L, R OUT/SUB2-L, R OUT. Control “INST 1 GAIN” and “INST 2
GAIN” (p. 9). Turn the equalizer on/off of MIC 1, 2.
Controls the respective parameters for INPUT, EQ and MIC 1, 2.
Turn the equalizer on/off of INST 1.
31
System Settings (MENU)
Parameter KNOB FUNC 14
Value (Bold: default) INST1-L, R EQ LO G INST1-L, R EQ HI G INST1-L, R EQ LM F INST1-L, R EQ LM Q INST1-L, R EQ LM G INST1-L, R EQ HM F INST1-L, R EQ HM Q INST1-L, R EQ HM G INST1-L, R EQ LVL INST1-L, R EQ LO C INST1-L, R EQ HI C INST2-L, R EQ SW INST2-L, R EQ LO G INST2-L, R EQ HI G INST2-L, R EQ LM F INST2-L, R EQ LM Q INST2-L, R EQ LM G INST2-L, R EQ HM F INST2-L, R EQ HM Q INST2-L, R EQ HM G INST2-L, R EQ LVL INST2-L, R EQ LO C INST2-L, R EQ HI C MIC1, 2 COMP MIC1, 2 NS INST 1, 2 NS RHYTHM OUT INPUT THRU PHONES MONITOR PHONES OUT MAIN-L, R EQ SW MAIN-L, R EQ LO G MAIN-L, R EQ HI G MAIN-L, R EQ LM F MAIN-L, R EQ LM Q MAIN-L, R EQ LM G MAIN-L, R EQ HM F MAIN-L, R EQ HM Q MAIN-L, R EQ HM G MAIN-L, R EQ LVL MAIN-L, R EQ LO C MAIN-L, R EQ HI C SUB1-L, R EQ SW
Explanation
Controls the respective parameters for INPUT, EQ and INST 1 L, R.
Turn the equalizer on/off of INST 2.
Controls the respective parameters for INPUT, EQ and INST 2 L, R.
Controls the respective parameters for INPUT and DYNAMICS. Control “RHYTHM
OUT” (p. 13) of MIXER. Controls the “INPUT THRU” (p. 12) for INPUT/RHYTHM in
OUTPUT/ROUTING. Controls the “PHONES MONITOR” (p. 12) for OUTPUT/ROUTING.
Control “PHONES OUT” (p. 13) of MIXER. Turn the equalizer on/off of MAIN.
Controls the respective parameters for OUTPUT, EQ and MAIN L, R.
Turn the equalizer on/off of SUB 2.
32
Parameter KNOB FUNC 14
Value (Bold: default) SUB1-L, R EQ LO G SUB1-L, R EQ HI G SUB1-L, R EQ LM F SUB1-L, R EQ LM Q SUB1-L, R EQ LM G SUB1-L, R EQ HM F SUB1-L, R EQ HM Q SUB1-L, R EQ HM G SUB1-L, R EQ LVL SUB1-L, R EQ LO C SUB1-L, R EQ HI C SUB2-L, R EQ SW SUB2-L, R EQ LO G SUB2-L, R EQ HI G SUB2-L, R EQ LM F SUB2-L, R EQ LM Q SUB2-L, R EQ LM G SUB2-L, R EQ HM F SUB2-L, R EQ HM Q SUB2-L, R EQ HM G SUB2-L, R EQ LVL SUB2-L, R EQ LO C SUB2-L, R EQ HI C MFX COMP MFX REVERB (4) PANEL MODE DISPLAY MODE INDICATOR
Explanation
System Settings (MENU)
Controls the respective parameters for OUTPUT, EQ and SUB 1 L, R.
Turn the equalizer on/off of SUB 2.
Controls the respective parameters for OUTPUT, EQ and SUB 2 L, R.
Control “COMP” (p. 13) of OUTPUT/MASTER FX. Control “REVERB” of OUTPUT/MASTER
FX. Switches between “PANEL PLAY” and “PANEL UNDO” (p. 14) for CTL FUNC.
Switches the play screen. Control “INDICATOR” (p. 30) of SETUP.
FACTORY RESET
Parameter FACTORY RESET
Value (Bold: default)
Explanation
Specifies the settings that will be returned to their factory-set state.
MEMORY
Memory 0199
SYSTEM
System settings
MEM+SYS
Memory 0199 and system settings
33
Input FX/Track FX List
Parameters indicated by the ” ” symbol can be controlled by the [INPUT FX]/[TRACK FX] knobs.
About FX sequences
This function changes the effects according to the settings of each step
(maximum of 16 steps). You can also change effects in sync with loop
performance.
5 Effects that can use the FX sequence function are indicated by the
mark.
5 The FX sequence parameters are shown below. Set the parameters for each effect.
Parameter SW SYNC RETRIG
TARGET
RATE MAX VAL116
Value (Bold: default)
Explanation
OFF, ON
Sets the FX sequence function on/off.
OFF, ON
Sets whether to synchronize loop playback with the FX sequence (ON) or not (OFF). When this is “ON”, the beginning of the FX sequence (step 1) is cued up.
OFF, ON
When this is “ON” and you press the [A][D] buttons to turn the effects on for which FX sequences have been set, the beginning of the phrase used for loop playback is lined up with the beginning of the FX sequence (step 1).
Sets the parameter that the FX sequence changes.
- The value (parameter) changes depending on the effect. Parameters that can be set as a TARGET are marked with a 2 (2; blue stars indicate initial values).
0100, 4MEAS, 2MEAS, 1MEAS,
¸`
Sets the step’s cycle.
116
Sets the maximum number of steps.
116
Sets how much the effect for each step changes.
Types available for both Input FX and Track FX
LPF
Low pass filter. This reduces the volume of all frequencies above the cutoff frequency.
Parameter RATE DEPTH RESONANCE CUTOFF
STEP RATE
Value (Bold: default) Explanation
4MEAS, 2MEAS, 1MEAS, ¸`, 0100
Sets the rate of modulation.
2 050100
Sets the depth of modulation.
050100
Sets the intensity of the effect.
050100 2
OFF, 4MEAS, 2MEAS, 1MEAS, ¸`, 0100
Sets the cutoff frequency of the filter.
Sets the rate of the stepped change for the effect.
HPF
High pass filter. This cuts the frequencies in the region below the cutoff frequency.
Parameter RATE DEPTH RESONANCE CUTOFF
STEP RATE
Value (Bold: default) 4MEAS, 2MEAS, 1MEAS, ¸`, 0100 2 050100 050100
Explanation Sets the rate of modulation. Sets the depth of modulation. Sets the intensity of the effect.
050100 2
Sets the cutoff frequency of the filter.
OFF, 4MEAS, 2MEAS, Sets the rate of the stepped 1MEAS, ¸`, 0100 change for the effect.
BPF
Band pass filter. This leaves only the frequencies in the region of the cutoff frequency, and cuts the rest.
Parameter RATE DEPTH RESONANCE CUTOFF
STEP RATE
Value (Bold: default) Explanation
4MEAS, 2MEAS, 1MEAS, ¸`, 0100 Sets the rate of modulation.
2 050100
Sets the depth of modulation.
050100
Sets the intensity of the effect.
050100 2
OFF, 4MEAS, 2MEAS, 1MEAS, ¸`, 0100
Sets the cutoff frequency of the filter.
Sets the rate of the stepped change for the effect.
PHASER
Gives the sound a swishing quality by adding a phase-shifted sound.
Parameter RATE DEPTH RESONANCE MANUAL STEP RATE D.LEVEL
E.LEVEL
STAGE
Value (Bold: default) 4MEAS, 2MEAS, 1MEAS, ¸, 0100 2 050100 2 050100 2 050100 OFF, 4MEAS, 2MEAS, 1MEAS, ¸
, 0100
2 0100
Explanation
Sets the speed of the effect.
Sets the richness of the effect. Sets the intensity of the effect. Sets the
center frequency of the phaser effect. Sets the rate of the stepped change for
the effect. Sets the volume of the direct sound.
050100 2
4, 8, 12, BI-PHASE
Sets the volume level of the effect sound.
Selects the number of stages that the phaser effect will use.
34
Input FX/Track FX List
FLANGER
Produces a metallic resonance reminiscent of a jet airplane taking off and landing.
Parameter RATE DEPTH RESONANCE MANUAL STEP RATE D.LEVEL E.LEVEL
SEPARATION
Value (Bold: default)
4MEAS, 2MEAS, 1MEAS, ¸`, 0100
Explanation Sets the speed of the effect.
2 050100
Sets the richness of the effect.
2 050100
Sets the intensity of the effect.
2 050100
OFF, 4MEAS, 2MEAS, 1MEAS, ¸`, 0100
Sets the center frequency of the flanger effect.
Sets the rate of the stepped change for the effect.
2 0100
Sets the volume of the direct sound.
050100 2
Sets the volume of the effect sound.
2 0100
Sets the amount of separation (how wide the sound seems).
SYNTH
Generates a synthesizer sound.
Parameter FREQUENCY RESONANCE
DECAY
Value (Bold: default) 2 050100 2 050100
2 050100
BALANCE
050100
Explanation Sets the frequency of the filter.
Sets the intensity of the effect.
Sets the time over which the filter frequency will change.
Adjusts the volume balance between the direct sound and the synth sound.
LO-FI
This effect intentionally degrades the sound to create a distinctive character.
Parameter BITDEPTH SAMPLERATE BALANCE
Value (Bold: default) OFF, 3181 OFF, 1/21/41/32 050100
Explanation Sets the bit depth. When this is “OFF”, the sound quality is not
degraded.
Sets the sampling rate.
Adjusts the volume balance between the direct sound and the effect sound.
RADIO
Produces a radio voice.
Parameter LO-FI
Value (Bold: default) 1510
LEVEL
050100
Explanation Sets the amount of blurring.
Sets the volume of the effect sound.
RING.MOD
Gives a metallic character to the sound, creating the impression that the sound is going out of focus.
Parameter FREQUENCY BALANCE
MODE
Value (Bold: default) Explanation
050100 2
050100
Sets the frequency of the internal oscillator.
Adjusts the volume balance between the direct sound and the effect sound.
Specifies the operating mode for the effect.
1
Operates using the algorithm from the previous RC series.
2
Operates using a new algorithm.
G2B
Transforms a guitar sound into a bass sound.
Parameter BALANCE
MODE
Value (Bold: default) Explanation
050100
Adjusts the volume balance between the direct sound and the effect sound.
Specifies the operating mode for the effect.
Operates using the algorithm from
1
the previous RC series.
2
Operates using a new algorithm.
SUSTAINER
This effect brings down loud input sound and makes quiet input sound louder, giving the original sound a long sustaining quality without adding distortion.
Parameter ATTACK
RELEASE
LEVEL LOW GAIN HI GAIN SUSTAIN
Value (Bold: default) 050100
050100
050100 -20020 dB -20020 dB 050100
Explanation Sets the strength of the attack when picking.
Sets the range (time) over which signals are adjusted to a certain volume.
Larger values result in longer sustain.
Sets the volume of the effect sound.
Sets the gain for the low frequency range.
Sets the gain for the high frequency range.
Sets the sustain time.
35
Input FX/Track FX List
AUTO RIFF
Automatically creates phrases based on the input sound.
- Because of the need to analyze the pitch, chords (two or more sounds played simultaneously) cannot be played.
Parameter PHRASE TEMPO
HOLD
ATTACK LOOP KEY BALANCE
Value (Bold: default) P130 4MEAS, 2MEAS, 1MEAS, ¸`, 0100
OFF, ON
050100 OFF, ON
Explanation Selects the phrase for creating the auto riff.
Sets the speed of the phrase.
If you turn hold “ON” after you pick a note, the effect sound will continue
even after there is no input signal. Sets the loudness of the attack sound
added to each phrase. If LOOP is turned “ON”, the phrase will be played back
continuously.
C (Am)B (G#m)
Sets the key of the phrase.
050100
Adjusts the volume balance between the direct sound and the effect sound.
SLOW GEAR
This produces a volume-swell effect (“violin-like” sound).
Parameter SENS RISE TIME LEVEL
MODE
Value (Bold: default) Explanation
050100
Sets the effect’s sensitivity when you’re picking.
050100
Sets the time needed for the volume to reach its maximum from the moment you begin picking.
050100
Sets the volume of the effect sound.
Specifies the operating mode for the effect.
1
Operates using the algorithm from the previous RC series.
2
Operates using a new algorithm.
TRANSPOSE
Transposes the sound when you turn the FX on.
Parameter TRANS
MODE
Value (Bold: default) Explanation
-120+12 2
Sets the amount of transposition in semitone units that will occur when the FX is on.
Specifies the operating mode for the effect.
1
Operates using the algorithm from the previous RC series.
2
Operates using a new algorithm.
PITCH BEND
Creates a pitch bend effect.
Parameter PITCH BEND
MODE
Value (Bold: default) Explanation
-3+4OCT
Sets the amount of pitch shift in octave steps.
050100 2
Sets the amount of bend within the range specified by the PITCH value.
Specifies the operating mode for the effect.
1
Operates using the algorithm from the previous RC series.
2
Operates using a new algorithm.
ROBOT
Cyber-robot voice. Parameter NOTE
FORMANT
MODE
Value (Bold: default) Explanation
Sets the pitch (fixed) for the robot
CB
voice.
-500+50
Negative () settings give the voice a more masculine character, while positive (+) settings make the voice more feminine.
Specifies the operating mode for the effect.
1
Operates using the algorithm from
the previous RC series.
2
Operates using a new algorithm.
ELECTRIC
Adjusts the pitch in steps to make the sound more mechanical.
Parameter SHIFT FORMANT SPEED STABILITY
SCALE
Value (Bold: default) Explanation
-120+12
Sets how much the pitch changes.
-500+50
Negative () settings give the voice a more masculine character, while positive (+) settings make the voice more feminine.
0510
Sets how quickly the pitch changes.
-100+10
Adjusts how easily the pitch changes. Larger values make the pitch more stable.
This sets how the pitch is adjusted.
CHROMATIC
The pitch is adjusted in semitones.
C (Am)B (G#m)
The pitch is adjusted to match the key.
36
Input FX/Track FX List
HRM MANUAL
Adds a harmony to match the value set for the “KEY”.
Parameter
VOICE
FORMANT PAN KEY D.LEVEL HRM LEVEL
Value (Bold: default) Explanation These parameters select the type of harmony.
OCT-, OCT+
Adds sound an octave lower or higher.
-64TH, -3RD, +3RD, Adds harmony at the specified
+46TH
pitch interval of the diatonic scale.
UNISON
Produces the impression that another person is singing the same melody along with you.
-500+50
Adjusts the vocal character of the harmony part.
L50CENTERR50
Sets the panning of the harmony part.
C (Am)B (G#m)
Sets the key used when adding harmony.
0100
Sets the volume of the direct sound.
080100
Sets the volume of the harmony sound.
HRM AUTO (M)
Adds harmony based on the MIDI note messages received (chords and chord progressions).
Parameter
VOICE
FORMANT PAN
HRM MODE
KEY D.LEVEL HRM LEVEL
Value (Bold: default) Explanation These parameters select the type of harmony.
OCT-, OCT+
Adds sound an octave lower or higher.
LOWER, LOW, HIGH, Adds harmony at the specified
HIGHER
pitch interval of the diatonic scale.
UNISON
Produces the impression that another person is singing the same melody along with you.
-500+50
Adjusts the vocal character of the harmony part.
L50CENTERR50
Adjusts the panning of the harmony part.
This selects the data used when creating harmonies.
HYBRID
A harmony is added based on the key that was set and the MIDI note messages (chords) received.
AUTO
A harmony is added based on the inputted chords and chord progressions.
C (Am)B (G#m)
Sets the key used when adding harmony.
0100
Sets the volume of the direct sound.
080100
Sets the volume of the harmony sound.
VOCODER
Vocoder sound that uses the audio input to modulate the sound of the track you specify.
Parameter CARRIER
TONE ATTACK MOD SENS BALANCE
CARRIER THRU
Value (Bold: default) MIC1, MIC2, INST1-L, INST1-R, INST2-L, INST2-R, TRACK15
-500+50 050100 -500+50
050100
OFF, ON
Explanation Sets the input or track (TRACK 15) that will be used as the basis (carrier) of the vocoder sound.
- If the specified track is empty, you won’t hear the vocoder.
Adjusts the tonal character of the vocoder part. Sets the attack of the sound. Sets the sensitivity by which the audio input will control the modulation. Adjusts the volume balance between the direct sound and the vocoder sound. When this is “OFF”, the carrier output is muted while the effect is on. - Available if CARRIER is set to input (MIC1INST2-R).
OSC VOC (M)
Creates a vocoder sound based on the MIDI note messages received.
Parameter CARRIER
TONE ATTACK OCTAVE MOD SENS
RELEASE
BALANCE
Value (Bold: default) SAW, VINTAGE SAW, DETUNE SAW, SQUARE, RECT -500+50
050100 -2OCT, -1OCT, 0, +1OCT
-500+50
050100
050100
Explanation
Selects the carrier waveform (the basic sound).
Adjusts the tonal character of the vocoder part. Sets the attack of the sound.
Sets the pitch of the sound.
Adjusts the sensitivity by which the audio input will control the modulation.
Sets the decay time (release time) for sound initiated by a note message.
Adjusts the volume balance between the direct sound and the vocoder sound.
37
Input FX/Track FX List
OSC BOT
Plays the oscillator to match the value in the “NOTE” parameter. This plays melodies and other phrases in combination with the sequencer.
Parameter OSC
TONE ATTACK NOTE MOD SENS
BALANCE
Value (Bold: default) SAW, VINTAGE SAW, DETUNE SAW, SQUARE, RECT -500+50
050100 2 C1C2G9
-500+50
050100
Explanation
Selects the oscillator waveform.
Adjusts the tonal character of the oscillator. Sets the attack of the sound.
Sets the note used to make the oscillator sound. Sets the sensitivity by which
the audio input will control the modulation. Adjusts the volume balance
between the direct sound and the effect sound.
PREAMP
Simulates the characteristics of a guitar amplifier.
Parameter
AMP TYPE
SPK TYPE GAIN T-COMP BASS MIDDLE TREBLE PRESENCE MIC TYPE MIC DIS MIC POS
E.LEVEL
Value (Bold: default)
Explanation
JC-120, NATURAL CLEAN, FULL RANGE, COMBO CRUNCH, STACK CRUNCH, HIGAIN STACK, POWER DRIVE, EXTREM LEAD, CORE METAL
Selects the preamp type.
OFF, ORIGINAL, 1×8″, 1×10″, 1×12″, 2×12″, 4×10″, 4×12″, 8×12″
Selects the speaker type.
050120
Sets the distortion of the amp.
-100+10
Adjusts the sense of compression of the amp.
050100
Adjusts the tone for the low frequency range.
050100
Adjusts the tone for the middle frequency range.
050100
Adjusts the tone for the high frequency range.
050100
Adjusts the tone for the ultra high frequency range.
DYN57, DYN421,
Selects the mic type.
CND451, CND87, FLAT
OFF MIC, ON MIC
Sets the distance between the mic and speaker.
CENTER, 110 cm
Sets the mic position.
050100
Sets the volume of the effect sound.
DIST
This effects that distort the sound.
Parameter TYPE TONE DIST D.LEVEL
E.LEVEL
Value (Bold: default) VOCAL, BOOST, OD, DS, METAL, FUZZ -500+50 050100
0100
050100
Explanation
Selects the distortion type.
Sets the tonal character. Sets the degree of distortion. Sets the volume of
the direct sound. Sets the volume of the effect sound.
DYNAMICS
Makes the volume more consistent, and produces a more evenly balanced lowfrequency range.
Parameter TYPE DYNAMICS
Value (Bold: default)
NATURALCOMP, MIXER COMP, LIVE COMP, NATURAL LIM, HARD LIM, JINGL COMP, HARD
COMP, SOFT COMP, CLEAN COMP, DANCE COMP, ORCH COMP, VOCAL COMP, ACOUSTIC, ROCK
BAND, ORCHESTRA, LOW BOOST, BRIGHTEN, DJs VOICE, PHONE VOX
-200+20
Explanation
Selects the type of the DYNAMICS effect.
Adjusts the amount of difference between soft and loud.
EQ
Adjusts the tone as a equalizer.
Parameter LO LO-MID LO-MID FREQ
LO-MID Q HI-MID HI-MID FREQ
HI-MID Q HIGH LEVEL
Value (Bold: default) Explanation
-200+20 dB
Adjusts the low frequency range tone.
-200+20 dB
Adjusts the low-middle frequency range tone.
Specifies the center of the 20.0800 Hz10.0 kHz frequency range that will be
adjusted by the LO-MID.
0.5, 1, 2, 4, 8, 16
Adjusts the width of the area affected by the equalizer centered at the LO-MID FREQ.
Higher values will narrow the area.
-200+20 dB
Adjusts the high-middle frequency range tone.
20.0 Hz3.15 kHz 10.0 kHz
0.5, 1, 2, 4, 8, 16
Specifies the center of the frequency range that will be adjusted by the HI-
MID. Adjusts the width of the area affected by the equalizer centered at the
HI-MID FREQ.
Higher values will narrow the area.
-200+20 dB
Adjusts the high frequency range tone.
050100
Sets the overall volume of the equalizer.
38
Input FX/Track FX List
ISOLATOR
Divides the audio input into three ranges (LO, MID, HI) and cuts the specified region. You can cut in synchronization with the tempo.
Parameter BAND
RATE BAND LEVEL
Value (Bold: default)
LOW, MIDDLE, HIGH
4MEAS, 2MEAS, 1MEAS, ¸`, 0100 050100
Explanation Selects the range (LOW, MID, HIGH) that will be cut.
Sets the rate of modulation.
Sets the amount of cut.
DEPTH STEP RATE WAVEFORM
050100 2
OFF, 4MEAS, 2MEAS, 1MEAS, ¸`, 0100
TRI, SQR
Sets the depth of modulation.
Sets the rate of the stepped change for the effect. Sets how the volume level
changes (the curve).
OCTAVE
Adds a note one (or two) octave lower, creating a richer sound.
Parameter OCTAVE MODE
OCT.LEVEL
Value (Bold: default) Explanation
-1OCT, -2OCT, -1OCT&-2OCT
Selects the octave that will be sounded.
Specifies the operating mode for the effect.
Operates using the algorithm from
1
the previous RC series.
2
Operates using a new algorithm.
050100 2
Sets the volume level of the octave sound.
AUTO PAN
Cyclically varies the stereo position (panning) of the sound.
Parameter RATE WAVEFORM DEPTH
INIT PHASE
STEP RATE
Value (Bold: default) 4MEAS, 2MEAS, 1MEAS, ¸, 0100 050100 050100 0180 OFF, 4MEAS, 2MEAS, 1MEAS, ¸
, 0100
Explanation
Sets the rate of change in the pan position.
Adjusts how the volume level changes (the curve). Higher values create more
abrupt change.
Sets the depth by which pan will change.
Sets the PAN position. Specifies the rotational angle of the phase from the
default (when the effect is turned on) of 0 (center).
Sets the rate of the stepped change for the effect.
MANUAL PAN
This effect lets you use the [INPUT FX] and [TRACK FX] knobs to change the stereo position (panning).
Parameter
Value (Bold: default) Explanation
POSITION
L50CENTERR50 2
Sets the pan.
STEREO ENHANCE
Gives a stereo feeling to a mono signal.
Parameter
Value (Bold: default)
LOW CUT
FLAT, 20.0 Hz12.5 kHz
HIGH CUT ENHANCE
20.0 Hz12.5 kHz, FLAT
050100
Explanation
Specifies the frequency at which the low cut filter begins to take effect.
When “FLAT” is selected, the low cut filter will have no effect.
Specifies the frequency at which the high cut filter begins to take effect.
When “FLAT” is selected, the high cut filter will have no effect.
Adjusts the depth of enhance.
TREMOLO
Tremolo is an effect that creates a cyclic change in volume.
Parameter RATE
Value (Bold: default)
4MEAS, 2MEAS, 2 1MEAS, `,
085100
Explanation
Sets the frequency (speed) of the change.
DEPTH WAVEFORM
050100 2
050100
Sets the depth of the effect.
Adjusts how the volume level changes (the curve). Higher values create more
abrupt change.
VIBRATO
This effect creates vibrato by slightly modulating the pitch.
Parameter RATE
Value (Bold: default)
4MEAS, 2MEAS, 1MEAS, `, 050100
Explanation Sets the rate of the vibrato.
DEPTH COLOR D.LEVEL E.LEVEL
050100 2
050100
2 050100
2 050100
Sets the depth of the vibrato.
Higher settings produce more complex modulation. Sets the volume of the direct
sound. Sets the volume of the effect sound.
39
Input FX/Track FX List
PATTERN SLICER
This consecutively interrupts the sound to create the impression that a rhythm backing phrase is being played.
Parameter RATE DUTY ATTACK PATTERN DEPTH
Ver. 1.2
COMP THRESHOLD
Ver. 1.2
COMP GAIN
Value (Bold: default) 4MEAS, 2MEAS, 1MEAS, ¸`, 0100 15099 035100 P0120
0100
-300 dB
Explanation
Sets the rate at which the sound will be cut.
Adjusts the length of the sound for the slice pattern.
Sets the attack volume of the slice pattern.
Selects the slice pattern that will be used to cut the sound.
Adjusts the depth to which the slice pattern is applied. Adjust this as
appropriate for the inputsignal. When the input signal level exceedsthis
threshold level, compression will beapplied.
0+2+20 dB
Sets the volume of the sound.
STEP SLICER
This continuously “slices” the sound according to the step settings.
Parameter RATE STEP MAX STEP LENGTH STEP LEVEL DEPTH
Ver. 1.2
COMP THRESHOLD
Ver. 1.2
COMP GAIN
Value (Bold: default) 4MEAS, 2MEAS, 1MEAS, ¸`, 0100 116 150100 0100
0100
-300 dB
Explanation Sets the rate at which the sound will be cut.
Sets the maximum number of steps.
Sets the length of one step.
Sets the volume of one step.
Adjusts the depth to which the slice pattern is applied. Adjust this as
appropriate for the inputsignal. When the input signal level exceedsthis
threshold level, compression will beapplied.
0+6+20 dB
Sets the volume of the sound.
PANNING DELAY
This delay is specifically for stereo output. This allows you to obtain the tap delay effect that divides the delay time, then deliver them to L and R channels.
Parameter TIME FEEDBACK D.LEVEL
LOW CUT
HIGH CUT
E.LEVEL
Value (Bold: default) 12002000 ms, ` 116 0100
FLAT, 20.0 Hz12.5 kHz
20.0 Hz12.5 kHz, FLAT
050120
Explanation Sets the delay time.
Sets the number of delay repeats.
Sets the volume of the direct sound.
Sets the frequency at which the low cut filter begins to take effect. When
“FLAT” is selected, the low cut filter will have no effect.
Sets the frequency at which the high cut filter begins to take effect. When
“FLAT” is selected, the high cut filter will have no effect.
Sets the volume of the delay sound.
REVERSE DELAY
This produces an effect where the sound is played back in reverse.
Parameter TIME FEEDBACK D.LEVEL
LOW CUT
HIGH CUT
E.LEVEL
Value (Bold: default) 12002000 ms, ` 116 0100
FLAT, 20.0 Hz12.5 kHz
20.0 Hz12.5 kHz, FLAT
050120
Explanation Sets the delay time.
Sets the number of delay repeats.
Sets the volume of the direct sound.
Sets the frequency at which the low cut filter begins to take effect. When
“FLAT” is selected, the low cut filter will have no effect.
Sets the frequency at which the high cut filter begins to take effect. When
“FLAT” is selected, the high cut filter will have no effect.
Sets the volume of the delay sound.
DELAY
Adds a delayed sound to the direct sound, giving the sound greater depth or creating special effects.
Parameter TIME FEEDBACK D.LEVEL
LOW CUT
HIGH CUT
E.LEVEL
Value (Bold: default) 12002000 ms, ` 116 0100
FLAT, 20.0 Hz12.5 kHz
20.0 Hz12.5 kHz, FLAT
050120
Explanation Sets the delay time.
Sets the number of delay repeats.
Sets the volume of the direct sound.
Sets the frequency at which the low cut filter begins to take effect. When
“FLAT” is selected, the low cut filter will have no effect.
Sets the frequency at which the high cut filter begins to take effect. When
“FLAT” is selected, the high cut filter will have no effect.
Sets the volume of the delay sound.
MOD DELAY
This is a delay with a pleasant chorus-type effect added to the delay repeats.
Parameter TIME FEEDBACK MOD DEPTH D.LEVEL
LOW CUT
HIGH CUT
E.LEVEL
Value (Bold: default) 12002000 ms, ` 116 050100 0100
FLAT, 20.0 Hz12.5 kHz
20.0 Hz12.5 kHz, FLAT
050120
Explanation Sets the delay time.
Sets the number of delay repeats.
Sets the modulation depth of the delay sound.
Sets the volume of the direct sound.
Sets the frequency at which the low cut filter begins to take effect. When
“FLAT” is selected, the low cut filter will have no effect.
Sets the frequency at which the high cut filter begins to take effect. When
“FLAT” is selected, the high cut filter will have no effect.
Sets the volume of the delay sound.
40
Input FX/Track FX List
TAPE ECHO1, 2
A virtual tape echo that produces a realistic tape delay sound.
TAPE ECHO1: TAPE ECHO2:
Operates using the algorithm from the previous RC series. Operates using a new algorithm.
TAPE ECHO1
Parameter REPEAT RATE INTENSITY D.LEVEL
BASS
TREBLE
E.LEVEL
Value (Bold: default) 050100 050100 0100
-500+50
-500+50
050120
Explanation Sets the tape speed.
Sets the amount of delay repeats.
Sets the volume of the direct sound.
Adjusts the tone for the low frequency range.
Adjusts the tone for the high frequency range.
Sets the volume of the effect sound.
TAPE ECHO2
Parameter REPEAT RATE INTENSITY D.LEVEL
LOW CUT
HIGH CUT
E.LEVEL
Value (Bold: default) 12002000 ms, ` 050100 0100
FLAT, 20.0 Hz12.5 kHz
20.0 Hz12.5 kHz, FLAT
050120
Explanation Sets the tape speed.
Sets the amount of delay repeats.
Sets the volume of the direct sound.
Sets the frequency at which the low cut filter begins to take effect. When
“FLAT” is selected, the low cut filter will have no effect.
Sets the frequency at which the high cut filter begins to take effect. When
“FLAT” is selected, the high cut filter will have no effect.
Sets the volume of the effect sound.
GRANULAR DELAY
Repeats a short portion of the input sound, giving it a buzzy character or producing the effect of playing a roll.
Parameter TIME FEEDBACK
E.LEVEL
Value (Bold: default) 050100 070100
050100
Explanation
Sets the spacing of the repeats.
Sets the length that will be repeated. Sets the volume of the effect sound.
TWIST
Produces an aggressive sense of rotation.
Parameter RELEASE
RISE FALL LEVEL
Value (Bold: default) Explanation Selects how the rotation should stop when the effect is turned off.
FALL
Rotation stops when you switch to off.
FADE
When you switch to off, fadeout occurs while continuing the rotation.
050100
Sets the amount of time it is to take for the effect to transition to the maximum.
050100
Sets the time to fade-out when RELEASE is set to “FADE”.
050100
Sets the volume of the effect sound.
ROLL1, 2
This loops the input sound over a short cycle, splitting the length.
ROLL1: Operates using the algorithm from the previous RC series. ROLL2:
Operates using a new algorithm.
ROLL1
Parameter TIME FEEDBACK ROLL
BALANCE
Value (Bold: default) Explanation
11000 ms, ¸`
Sets the loop rate.
150100
Sets the number of repetitions for ROLL when ROLL is “OFF”.
OFF, 1/2, 1/4, 1/8, 1/16 Splits and changes the loop cycle set in the TIME parameter.
050100
Adjusts the volume balance between the direct sound and the effect sound.
ROLL2
Parameter TIME REPEAT
ROLL
BALANCE
Value (Bold: default) Explanation
11000 ms, ¸`
Sets the loop rate.
150100, INF
Sets the number of repetitions for ROLL when ROLL is “OFF”.
OFF, 1/2, 1/4, 1/8, 1/16
Splits and changes the loop cycle set in the TIME parameter.
050100
Adjusts the volume balance between the direct sound and the effect sound.
WARP
Produces a dream-like sound.
Parameter LEVEL
Value (Bold: default) 050100
Explanation
Adjusts the volume of the effect sound.
41
Input FX/Track FX List
FREEZE
This “freeze function” gives the effect of making sounds sustain indefinitely.
Parameter ATTACK RELEASE DECAY SUSTAIN
BALANCE
Value (Bold: default) 030100 030100 030100 030100
050100
Explanation
Sets the fade time until the effect sound is output. Sets the fade time over
which the effect sound disappears. Adjusts the decay of the effect sound.
Adjusts the sustain of the effect sound.
Adjusts the volume balance between the direct sound and the effect sound.
CHORUS
In this effect, a slightly detuned sound is added to the original sound to add depth and breadth.
Parameter RATE DEPTH D.LEVEL
LOW CUT
HIGH CUT
E.LEVEL
Value (Bold: default) 050100, ` 050100 0100
FLAT, 20.0 Hz12.5 kHz
20.0 Hz12.5 kHz, FLAT
050100
Explanation
Sets the rate of the chorus effect.
Sets the depth of the chorus effect.
Sets the volume of the direct sound.
Sets the frequency at which the low cut filter begins to take effect. When
“FLAT” is selected, the low cut filter will have no effect.
Sets the frequency at which the high cut filter begins to take effect. When
“FLAT” is selected, the high cut filter will have no effect.
Sets the volume of the chorus sound.
REVERB
Adds reverberation to the sound.
Parameter TIME
Value (Bold: default) 0.1310s
PRE DELAY
0500 ms
DENSITY
1510
D.LEVEL
0100
LOW CUT
FLAT, 20.0 Hz12.5 kHz
HIGH CUT E.LEVEL
20.0 Hz12.5 kHz, FLAT
050100
Explanation
Sets the length (time) of reverberation.
Sets the time until the reverb sound appears.
Sets the density of the reverb sound.
Sets the volume of the direct sound.
Sets the frequency at which the low cut filter begins to take effect. When
“FLAT” is selected, the low cut filter will have no effect.
Sets the frequency at which the high cut filter begins to take effect. When
“FLAT” is selected, the high cut filter will have no effect.
Sets the volume of the reverb sound.
GATE REVERB
This is a special type of reverb in which the reverberant sound is cut off before its natural length.
Parameter TIME PRE DELAY THRESHOLD D.LEVEL LOW CUT
HIGH CUT E.LEVEL
Value (Bold: default) 0.1310s 0500 ms
050100
0100 FLAT, 20.0 Hz12.5 kHz
20.0 Hz12.5 kHz, FLAT 050100
Explanation
Sets the length (time) of reverberation.
Sets the time until the reverb sound appears.
Sets the level at which the reverberation is cut. The reverberation is cut
once its level falls below this setting.
Sets the volume of the direct sound.
Sets the frequency at which the low cut filter begins to take effect. When
“FLAT” is selected, the low cut filter will have no effect.
Sets the frequency at which the high cut filter begins to take effect. When
“FLAT” is selected, the high cut filter will have no effect.
Sets the volume of the reverb sound.
REVERSE REVERB
A gate reverb whose reverberations gradually get louder (fading in), rather than decaying (fading out).
Parameter TIME PRE DELAY GATE TIME D.LEVEL LOW CUT
HIGH CUT E.LEVEL
Value (Bold: default) 0.1310s 0500 ms 0.10.51s 0100
FLAT, 20.0 Hz12.5 kHz
20.0 Hz12.5 kHz, FLAT
050100
Explanation
Sets the length (time) of reverberation.
Sets the time until the reverb sound appears.
Sets the time at which the reverberations start getting louder.
Sets the volume of the direct sound.
Sets the frequency at which the low cut filter begins to take effect. When
“FLAT” is selected, the low cut filter will have no effect.
Sets the frequency at which the high cut filter begins to take effect. When
“FLAT” is selected, the high cut filter will have no effect.
Sets the volume of the reverb sound.
42
Types available only for Track FX
NOTE
The effects shown below can only be used with FX A when the TRACK FX MODE (p.
6) is set to “MULTI”.
BEAT SCATTER
The track will be scrubbed in time with the beat.
Parameter TYPE LENGTH
Value (Bold: default) P14 THRU, ª¸`
Explanation Sets the type of scrub playback. Sets the length of scrub playback.
BEAT REPEAT
Plays the track repeatedly in time with the beat.
Parameter TYPE LENGTH
Value (Bold: default) Explanation Sets the direction in which repeat playback will occur.
FORWARD
Plays back forward.
REWIND
Plays back in reverse.
Alternates between playing back
MIX
forward and in reverse.
THRU, ¸~
Sets the repeat length.
BEAT SHIFT
The track will play shifted by the length of the beat.
Parameter TYPE SHIFT
Value (Bold: default) FUTURE, PAST THRU, ~¸ª
Explanation
Sets the direction in which the playback position will be shifted.
Sets the amount by which the playback position will be shifted.
VINYL FLICK
The track will sound as though you are touching the turntable.
Parameter FLICK
Value (Bold: default) 050100
Explanation
Sets the playback speed of the turntable.
Input FX/Track FX List
43
Rhythm Pattern List
GENRE
ACOUSTIC
BALLAD BLUES JAZZ FUSION
PATTERN
SIDE STICK BOSSA BRUSH1 BRUSH2 CONGA 8BEAT CONGA 16BEAT CONGA 4BEAT CONGA
SWING CONGA BOSSA CAJON1 CAJON2 SHUFFLE2 SIDE STICK1 SIDE STICK2 SIDE STICK3
SIDE STICK4 SHUFFLE1 8BEAT 16BEAT1 16BEAT2 SWING 6/8 BEAT 3BEAT 12BARS
SHUFFLE1 SHUFFLE2 SWING 6/8 BEAT JAZZ BLUES FAST 4BEAT HARD BOP BRUSH BOP
BRUSH SWING FAST SWNG MED SWING SLOW LEGATO JAZZ SAMBA 6/8 BEAT 16BEAT1
16BEAT2 16BEAT3 16BEAT4 16BEAT5 16BEAT6 16BEAT7 SWING 7/8 BEAT
BEAT
4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 3/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4
4/4 4/4 6/8 3/4 4/4 4/4 4/4 4/4 6/8 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 6/8
4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 7/8
GENRE
R&B SOUL FUNK POP
PATTERN
SWING1 SWING2 SWING3 SIDE STICK1 SIDE STICK2 SIDE STICK3 SHUFFLE1 SHUFFLE2
8BEAT1 16BEAT 7/8 BEAT SWING1 SWING2 SWING3 SWING4 16BEAT1 16BEAT2 16BEAT3
SIDESTK1 SIDESTK2 MOTOWN PERCUS 8BEAT1 8BEAT2 8BEAT3 8BEAT4 16BEAT1 16BEAT2
16BEAT3 16BEAT4 SWING1 SWING2 SWING3 8BEAT1 8BEAT2 16BEAT1 16BEAT2 PERCUS1
SHUFFLE1 SHUFFLE2 SIDE STICK1 SIDE STICK2 SWING1 SWING2 PERCUS2
BEAT
4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 7/8 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4
4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4
4/4 4/4 4/4 4/4 4/4 4/4 6/8
GENRE
SOFT ROCK
ROCK ALT ROCK
PATTERN
16BEAT1 16BEAT2 16BEAT3 16BEAT4 8BEAT SWING1 SWING2 SWING3 SWING4 SIDE STICK1
SIDE STICK2 PERCUS1 PERCUS2 8BEAT1 8BEAT2 8BEAT3 8BEAT4 8BEAT5 8BEAT6 16BEAT1
16BEAT2 16BEAT3 16BEAT4 SHUFFLE1 SHUFFLE2 SWING1 SWING2 SWING3 SWING4 RIDEBEAT
8BEAT1 8BEAT2 8BEAT3 8BEAT4 16BEAT1 16BEAT2 16BEAT3 16BEAT4 SWING 5/4 BEAT
BEAT
4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4
4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4
4/4 5/4
44
GENRE
PUNK HEAVY ROCK METAL TRAD
PATTERN
8BEAT1 8BEAT2 8BEAT3 8BEAT4 8BEAT5 8BEAT6 16BEAT1 16BEAT2 16BEAT3 SIDE STICK
8BEAT6 8BEAT1 8BEAT2 8BEAT3 16BEAT1 16BEAT2 16BEAT3 SHUFFLE1 SHUFFLE2 SWING1
SWING2 SWING3 8BEAT1 8BEAT2 8BEAT3 8BEAT4 8BEAT5 8BEAT6 2XBD1 2XBD2 2XBD3
2XBD4 2XBD5 TRAIN2 ROCKN ROLL TRAIN1 COUNTRY1 COUNTRY2 COUNTRY3 FOXTROT TRAD1
TRAD2
BEAT
4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4
4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 2/4 4/4 4/4 4/4 4/4
4/4 4/4 4/4 4/4
GENRE
WORLD BALLAM ELCTRO
PATTERN
BOSSA1 BOSSA2 SAMBA1 SAMBA2 BOOGALOO MERENGUE REGGAE LATIN ROCK1 LATIN ROCK2
LATIN PERC SURDO LATIN1 LATIN2 CUMBIA WALTZ1 WALTZ2 CHACHA BEGUINE RHUMBA
TANGO1 TANGO2 JIVE CHARLSTON ELCTRO01 ELCTRO02 ELCTRO03 ELCTRO04 ELCTRO05
ELCTRO06 ELCTRO07 ELCTRO08 5/4 BEAT
Rhythm Pattern List
BEAT
4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 2/4 3/4 3/4 4/4 4/4 4/4
4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 5/4
GENRE
GUIDE USER
PATTERN
2/4 TRIPLE 3/4 3/4 TRIPLE 4/4 4/4 TRIPLE BD 8BEAT BD 16BEAT BD SHUFFLE HH
8BEAT HH 16BEAT HH SWING1 HH SWING2 8BEAT1 8BEAT2 8BEAT3 8BEAT4 5/4 5/4 TRIPLE
6/4 6/4 TRIPLE 7/4 7/4 TRIPLE 5/8 6/8 7/8 8/8 9/8 10/8 11/8 12/8 13/8 14/8
15/8 SIMPLE BEAT (*1)
BEAT
2/4 3/4 3/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4 4/4
4/4 4/4 5/4 5/4 6/4 6/4 7/4 7/4 5/8 6/8 7/8 8/8 9/8 10/8 11/8 12/8 13/8 14/8
15/8 4/4
(*1) By using RC-505mk2 Rhythm Converter you can import rhythm patterns from your own SMF data.
45
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>