IVONO IV-M9-P01 Electric Sit-Stand Desk Instruction Manual

IVONO IV-M9-P01 Electric Sit-Stand Desk

Instructions of Safety and Warnings

• Any failure to comply with the safety and installation instructions in this manual may cause serious bodily injury.
  Any incomplete observation of the instructions, warnings and additional information marked with the “Note” may result in serious damage to the system or its components.

• This product can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Unplug the desk when the system isn’t in use, and place the power plug out of children reach.

• Persons with reduced physical, mental abilities and or lack of experience and knowledge must not use the product, unless they’re under supervision, understand the hazards involved or they have been thoroughly instructed in the use of the apparatus by a person who is responsible for the safety of these persons.

• Users should make sure that they never sit on the desktop in order to prevent serious bodily injury.

IV-M9-P01 &IV-M9-P02

 Electrical Safety Instructions

CAUTION
The product is powered by electricity. In order to avoid burns, fire and electric shock, please read the instructions carefully.

Don’t clean the product with water while the power is still connected.
Don’t disassemble or replace components while the power is still connected.
Never operate the system with a damaged cord or plug. Please contact your point of purchase to replace the damaged parts.
Never operate the system if it’s in moist environment or its electrical components have contact with liquids.
Don’t operate the system if the control box makes noise or odor. Alterations of the given power unit and control box aren’t allowed.

Other Safety Instructions

• Clear up all obstacles within the height adjustment range.
• Don’t leave the cords or plug unorganized in order to prevent tripping hazards.
• Any attempts to reconstruct the desk frame aren’t allowed.
• Don’t add anything to the adjustable junctions of the desk frame.
• Outdoor use is prohibited.

Disposal
The product with this mark indicates that this product shouldn’t be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the local recycle service or contact your point of purchase to withdrawn the product.

Attaching the Lifting Columns

• Carefully place the desktop (not included), crossbar pieces 01$ upside down on the blanket/floor.
• Insert one lifting column4l into one end of the crossbar with the head of the lifting column facing inward.
• Attaching the lifting column to the crossbar and side bracket using 4 M6x12 screws m-
• Repeat the same process to attach the other lifting column.

Adjusting the Frame

• Insert the Center Crossbar Q into both the Crossbar Pieces0/$.
• Adjust the crossbar to the size of the desktop. Ensure that the frame is placed in the center of the desktop.
• Insert and tighten 8 Screws g}.

Attaching the Side Brackets

• Insert the side bracket G) to each end of the crossbar as shown in the illustration.
• Fix each side bracket with crossbar using 2 M6x12 screws m.
• Repeat the same process to attach the other side bracket.

Attaching the Feet

• Attaching the foot Oto the lifting column using 4 M6x12 screwsa3 .
• Repeat the same process to attach the other foot.

Drilling to the Desktop

• Attaching the assembled desk frame to the desktop through the mounting holes found on the side brackets and crossbar as shown in the illustration using 8 ST4.Sx16 screwsO!).

Attention
Please include cable tray hanger in this step if available.

Inserting Cords into the Control Box

• Insert 2 motor cords into the ports marked Ml and M2. You will use an extension cable 4n to extend the motor cord.
• Insert the controller (t cord into the port marked HS.
• Insert the power cord Qinto the port marked AC.
• Do not plug into the power before the desk is fully assembled.

Your desk will include one of the control boxes below. Once identified, connect the cables as shown in the illustration.

Attaching the Control Box

• Remove the control box 0 from the mounting plate as shown.
  

• Attach the mounting plate to the desktop using 2 ST4.2×16 screws (I]).
  

• Attach the control box to the mounting plate with hearing a clicking sound.
  

Attaching the Controller

• Turn over the desk with the help of another person.
• Attach the controller to the desktop with 2 ST3.Sx12screws m.
• Run the cables through the cable clipsa) and attach the cable clips to the desktop with ST3.Sx12 screws m to ensure clean and neat surface.
  ACAUTION
  At least two people are required when turning over  the desk, or serious bodily injuries might occur.

Adjusting the Desk

• There are two adjustable foot pads under each foot. If the floor isn’t even, simply turn the pad to adjust the level to make the desk stable.
• Tip: Use a bubble level (not included) to check if the desktop is even.
• Using the desk for the first time, you will need to reset the system. Please refer to Digital Control Panel User Guide.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>