X-plorer Series 75 S and Series 75 S+ Vacuum Robot Rowenta User Manual
- June 11, 2024
- Rowenta
Table of Contents
X-plorer Series 75 S and Series 75 S+ Vacuum Robot Rowenta User Manual
OVERVIEW
- Infrared sensor
- LiDAR
- Bumper
- Power / Start / Pause
- Recharge
- Anti-collision strip
- Mop cloth assembly
- Central brush cover
- Central brush
- Wheel
- Battery
- Side brush
- Anti-drop sensor
- Front wheel
- Charging plots
- Dust bin and water tank release button
- On/off button *depending on model
- Auto Empty Station*
- Upper cover
- Dust bag chamber
- Indicator
- Charging plots
- Suction inlet
- Hygiene + dust bag
- Hygiene + dust bag handle
- 2-in-1 dust bin and water tank*
- Dust bin and water tank separation button
- Dust bin opening
- Filter opening
- Filter
- Water inlet cap
- Washable standard mop (grey and white)
- Washable scrubbing mop for hard stains (blue and white)*
- Washable microfiber mop to capture fine\ dust without water (green and white)*
- Docking station*
X-plorer Serie 75 S only: Remove the bottom cover of the docking station and connect the adapter. Pay attention to arranging adapter connection wire to avoid being wound during sweep. Put the bottom cover back.
X-plorer Serie 75 S and S+: To place the docking station or Auto Empty Station against the wall, make sure there is an empty area of 0.5 m on the side and 1.5 m in the front of the station. Do not install the station near stairs. The cable must be tight. Always place the station on hard floor. Do not place the station on carpet.
X-plorer Serie 75 S and S+: Connect the power cord plug to the main socket. The docking station lights when the robot is not plugged in. Remove the protective strip on the bumper to ensure proper operation of the device. X-plorer Serie 75 S and S+: Remove the protective strips and film on the product. Take the robot, install the side brush by pressing it gently to fix the side brush on the device and turn the power switch ON.
X-plorer Serie 75 S only: Place the robot on the docking station. The charging plots under the robot must touch those on the docking station. Please fully charge the robot before using it for the first time. The robot is fully charged when the white indicators on the robot are normaly set on (4-5 hours). When the robot is correctly plugged, the docking station light will switch off. X-plorer Serie 75 S+ only: Place the robot in front of the Auto Empty Station. Press the HOME button on the robot. The robot will automatically dock to the Auto Empty Station. Do not manually place the robot against the Auto Empty Station. After the robot is correctly connected to the station, the Auto Empty Station will automatically start dust collection for 20 seconds. Please note that the time between two adjacent suctions on the Auto Empty Station is over 5 minutes. Please fully charge the robot before using it for the first time. The robot is fully charged when the white indicators on the robot are normally set on (4-5 hours).
X-plorer Serie 75 S and S+: In order to extend the battery lifespan, always keep the robot charging on the docking station while not using it. When not using the robot for a long time, please fully charge the battery, switch OFF the robot and store it in a cool dry place
X-plorer Serie 75 S and S+: The robot has drop sensors to detect stairs and gaps. The robot will change direction when detecting them. In order to correctly detect the floor level difference, make sure there is no object (bag, shoes …) on the floor next to gaps, stairs or on the stair’s steps. The robot near stairs without object . The robot near stairs with shoes, bags or other objects (the robot will not properly detect the stairs and therefore fall).
“X-plorer Serie 75 S and S+: Press the power button on the top of the robot to start automatic cleaning or use the “X-plorer Series 75&95” application (see section 2). Press again the power button to pause / resume cleaning. Press the home button to end cleaning, the robot will return to the station. The robot automatically goes back to the station if the cleaning is completed or if the battery is low, to recharge itself. The robot will automatically resume to complete the remaining cleaning work.”
X-plorer Serie 75 S and S+: To fully benefit all the possibilities of your robot, download the free app “X-plorer Series 75&95” (you can flash the QR code above to find it on AppStore or Google Play) on your smartphone. Just follow the instructions in the application to enjoy the robot.
X-plorer Serie 75 S and S+: When the white indicator on the top of the robot is flashing slowly, the device is waiting for connection. When the white indicator is normally set on, the device is connected
Do not add cleaning agents in the water tank.
X-plorer Serie 75 S and S+: Wipe robot sensors (in front, sides and bottom of the robot) and the charging plots (back and bottom of the robot) with a clean, soft and dry cloth once a week. X-plorer Serie 75 S only: Wipe the window of the docking station once a week.
X-plorer Serie 75 S+ only: When the dust bag is full, the indicator of the Auto Empty Station is flashing in red. Please replace the dust bag. Open the upper cover. Pull up the dust bag handle and take out the dust bag. The indicator is normally on in red when the dust bag is not in place. Throw away the used dust bag. Install a new dust bag, make sure that the dust bag is correctly installed in place. Close the upper cover. The indicator is on in white when the station is in standby. The indicator is off when the robot is correctly connected to the station or the station is sleeping. If the indicator is flashing in red after replacing the dust bag, or if dust collection stops after a short period of time, the status is abnormal. Unplug the power plug, reverse the Auto Empty Station, and check whether the dust channel is blocked by foreign objects. If the dust channel is blocked by objects, unscrew the 6 screws of the transparent plastic cover of dust channel to remove it. Remove foreign objects. Replace the transparent cover. X-plorer Serie 75 S+ only: Clean the Auto Empty Station and the charging sensor head with a clean, soft and dry cloth. It is recommended to clean them once a week.
X-plorer Serie 75 S only: To clean the 2-in-1 dust bin and water tank, press and hold its release button and pull it outwards. Press the dust bin and water tank separation button to vertically lift the dust bin and seperate it from the water tank. Empty the water tank after each use. Open the dust bin and empty it, gently tap the dust bin to knock off dirt. Open the filter cover to take out the filter and gently tap it over a garbage bin to knock off dust. You can also wash the dust bin and the filter under water. Let them out to dry for 24 hours. Put the filter back to its original place. Reinstall the dust bin into the water tank, and then install the 2-in-1 dust bin and water tank back to the robot.
X-plorer Serie 75 S+ only: To clean the 2-in-1 dust bin and water tank, press and hold its release button and pull it outwards. Horizontally slide the dust bin to seperate it from the water tank. Empty the water tank after each use. Open the dust bin and empty it, gently tap the dust bin to knock off dirt. Open the filter cover to take out the filter and gently tap it over a garbage bin to knock off dust. You can also wash the dust bin and the filter under water. Let them out to dry for 24 hours. Put the filter back to its original place. Reinstall the dust bin into the water tank, and then install the 2-in-1 dust bin and water tank back to the robot.
X-plorer Serie 75 S and S+: To clean the central brush, turn OFF the robot and turn the robot upside down. Press down the lockers to take out the cover. Take out the the central brush upwards. Clean the central brush by cutting off the hair wound before replacing it back in the robot. Clean the central brush once a week.
X-plorer Serie 75 S and S+: To clean the side brush, remove it by unclipping it. Remove the hair wound before replacing it back on the robot. Clean the side brush once a month.
X-plorer Serie 75 S and S+: Replace the side brush every 6 months. Throw away the old brush and replace it with a new one. Clip the new side brush on the robot.
X-plorer Serie 75 S and S+: To clean the wheels, clean the front, left and right wheels once a month. The wheel shaft may be entangled by hair, cloth strips, etc. Clean them once a month.
X-plorer Serie 75 S and S+: Every 6 months replace the filter with a new one to maintain optimal performance
Do not throw the robot in the bin.
Straight line test
For measuring dust collection performance in accordance with IEC 62885-7,
testers can activate the straight line test by using the remote control
feature in the application menu. Press the POWER button three times to start
BOOST mode (maximum power).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>