ARDUINO ABX00027 Nano 33 IoT Module Instruction Manual
- June 4, 2024
- ARDUINO
Table of Contents
- ARDUINO ABX00027 Nano 33 IoT Module
- Features
- The Board
- Ratings
- Functional Overview
- Board Operation
- Connector Pinouts
- Mechanical Information
- Certifications
- FCC Caution
- FCC RF Radiation Exposure Statement:
- Company Information
- Reference Documentation
- Revision History
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ARDUINO ABX00027 Nano 33 IoT Module
- Product Reference Manual SKU: ABX00027
- SKU(with headers): ABX00032
Description
Nano 33 IoT and Nano 33 IoT with headers is a miniature sized module
containing a Cortex M0+ SAMD21 processor, a WiFi+BT module based on ESP32, a
crypto chip which can securely store certificates and pre-shared keys and a 6
axis IMU. The module can either be mounted as a DIP component (when mounting
pin headers), or as a SMT component, directly soldering it via the castellated
pads.
Target areas:
Maker, enhancements, basic IoT application scenarios
Features
SAMD21G18A
Processor
- 256KB Flash
- 32KB Flash
- Power On Reset (POR) and Brown Out Detection (BOD)
Peripherals
- 12 channel DMA
- 12 channel event system
- 5x 16 bit Timer/Counter
- 3x 24 bit timer/counter with extended functions 32 bit RTC
- Watchdog Time
- CRC-32 generator
- Full speed Host/Device USB with 8 end points
- 6x SERCOM (USART, I2C, SPI, LIN)
- Two channel I2S
- 12 bit 350ksps ADC (up to 16 bit with oversampling) 10 bit 350ksps DAC
- External Interrupt Controller (up to 16 lines)
Nina W102
Module
- Dual Core Tensilica LX6 CPU at up to 240MHz
- 448 KB ROM, 520KB SRAM, 2MB Flash
WiFi
- IEEE 802.11b up to 11Mbit
- IEEE 802.11g up to 54MBit
- IEEE 802.11n up to 72MBit
- 2.4 GHz, 13 channels
- -96 dBm sensitivity
Bluetooth® BR/EDR
- Max 7 peripherals
- 2.4 GHz, 79 channels
- U\p to 3 Mbit/s
- 8 dBm output power at 2/3 Mbit/s 11 dBm EIRP at 2/3 Mbit/s
- 88 dBm sensitivity
Bluetooth® Low Energy
- Bluetooth® 4.2 dual mode
- 2.4GHz 40 channels
- 6 dBm output power
- 9 dBm EIRP
- 88 dBm sensitivity
- Up to 1 Mbit/
MPM3610 (DC-DC)
- Regulates input voltage from up to 21V with a minimum of 65% efficiency @minimum load
- More than 85% efficiency @12V
ATECC608A (Crypto Chip)
- Cryptographic co-processor with secure hardware based key storage Protected storage for up to 16 keys, certificates or data
- ECDH: FIPS SP800-56A Elliptic Curve Diffie-Hellman
- NIST standard P256 elliptic curve support
- SHA-256 & HMAC hash including off-chip context save/restore
- AES-128 encrypt/decrypt, galois field multiply for GCM
LSM6DSL (6 axis IMU)
- Always-on 3D accelerometer and 3D gyroscope
- Smart FIFO up to 4 KByte based
- ±2/±4/±8/±16 g full scale
- ±125/±250/±500/±1000/±2000 dps full scale
The Board
As all Nano form factor boards, Nano 33 IoT and Nano 33 IoT with headers does
not have a battery charger but can be powered through USB or headers.
NOTE: Arduino Nano 33 IoT and Nano 33 IoT with headers only supports 3.3V
I/Os and is NOT 5V tolerant so please make sure you are not directly
connecting 5V signals to this board or it will be damaged. Also, as opposed to
Arduino Nano boards that support 5V operation, the 5V pin does NOT supply
voltage but is rather connected, through a jumper, to the USB power input.
Application Examples
Weather station: Using the Arduino Nano 33 IoT or Nano 33 IoT with headers together with a sensor and a OLED display, we can create a small weather station communicating temperature, humidity etc. directly to your phone.
Air quality monitor: Bad air quality may have serious effects on your
health. By assembling the board, with a sensor and monitor you can make sure
that the air quality is kept in indoor-environments. By connecting the
hardware assembly to an IoT application/API, you will receive real time
values.
Air drum: A quick and fun project is to create a small air drum. Connect
your board and upload your sketch from the Create Web Editor and start
creating beats with your audio workstation of your choice.
Ratings
Recommended Operating Conditions
Symbol | Description | Min | Max |
---|---|---|---|
Conservative thermal limits for the whole board: | -40 °C ( 40 °F) | 85°C ( |
185 °F)
Power Consumption
Symbol | Description | Min | Typ | Max | Unit |
---|---|---|---|---|---|
VINMax | Maximum input voltage from VIN pad | -0.3 | – | 21 | V |
VUSBMax | Maximum input voltage from USB connector | -0.3 | – | 21 | V |
PMax | Maximum Power Consumption | – | – | TBC | mW |
Functional Overview
Board Topology
Board topology top
Ref. | Description | Ref. | Description |
---|---|---|---|
U1 | ATSAMD21G18A Controller | U3 | LSM6DSOXTR IMU Sensor |
U2 | NINA-W102-00B WiFi/BLE Module | U4 | ATECC608A-MAHDA-T Crypto Chip |
J1 | Micro USB Connector | PB1 | IT-1185-160G-GTR Push button |
Ref. | Description | Ref. | Description |
---|---|---|---|
SJ1 | Open solder bridge (VUSB) | SJ4 | Closed solder bridge (+3V3) |
TP | Test points | xx | Lorem Ipsum |
Processor
The Main Processor is a Cortex M0+ running at up to 48MHz. Most of its pins
are connected to the external headers, however some are reserved for internal
communication with the wireless module and the on-board internal I2C
peripherals (IMU and Crypto).
NOTE: As opposed to other Arduino Nano boards, pins A4 and A5 have an internal pull up and default to be used as an I2C Bus so usage as analog inputs is not recommended. Communication with NINA W102 happens through a serial port and a SPI bus through the following pins.
SAMD21 Pin| SAMD21 Acronym| NINA Pin| NINA Acronym|
Description
---|---|---|---|---
13| PA08| 19| RESET_N| Reset
39| PA27| 27| GPIO0| Attention Request
41| PA28| 7| GPIO33| Acknowledge
23| PA14| 28| GPIO5| SPI CS
21| GPIO19| UART RTS| |
24| PA15| 29| GPIO18| SPI CLK
20| GPIO22| UART CTS| |
22| PA13| 1| GPIO21| SPI MISO
21| PA12| 36| GPIO12| SPI MOSI
31| PA22| 23| GPIO3| Processor TX Nina RX
32| PA23| 22| GPIO1| Processor RX Nina TX
WiFi/BT Communication Module
Nina W102 is based on ESP32 and is delivered with a pre-certified software
stack from Arduino. Source code for the firmware is available [9].
NOTE: Reprogramming the wireless module’s firmware with a custom one will invalidate compliance with radio standards as certified by Arduino, hence this is not recommended unless the application is used in private laboratories far from other electronic equipment and people. Usage of custom firmware on radio modules is the sole responsibility of the user. Some of the module’s pins are connected to the external headers and can be directly driven by ESP32 provided SAMD21’s corresponding pins are aptly tri-stated. Below is a list of such signals:
SAMD21 Pin| SAMD21 Acronym| NINA Pin| NINA Acronym|
Description
---|---|---|---|---
48| PB03| 8| GPIO21| A7
14| PA09| 5| GPIO32| A6
8| PB09| 31| GPIO14| A5/SCL
7| PB08| 35| GPIO13| A4/SDA
rypto
The crypto chip in Arduino IoT boards is what makes the difference with other
less secure boards as it provides a secure way to store secrets (such as
certificates) and accelerates secure protocols while never exposing secrets in
plain text. Source code for the Arduino Library that supports the Crypto is
available [10]
IMU
The board has an embedded 6 axis IMU which can be used to measure board
orientation (by checking the gravity acceleration vector orientation) or to
measure shocks, vibration, acceleration and rotation speed. Source code for
the Arduino Library that supports the IMU is available [11]
Power Tree
lenend
Board Operation
Getting Started – IDE
If you want to program your board while offline you need to install the Arduino
Desktop IDE [1] To connect the Arduino 33 IoT to your computer, you’ll need a
Micro-B USB cable. This also provides power to the board, as indicated by the
LED.
Getting Started – Arduino Web Editor
All Arduino boards, including this one, work out-of-the-box on the Arduino Web
Editor [2], by just installing a simple plugin. The Arduino Web Editor is
hosted online, therefore it will always be up-to-date with the latest features
and support for all boards. Follow [3] to start coding on the browser and
upload your sketches onto your board.
Getting Started – Arduino IoT Cloud
All Arduino IoT enabled products are supported on Arduino IoT Cloud which
allows you to Log, graph and analyze sensor data, trigger events, and automate
your home or business.
Sample Sketches
Sample sketches for the Arduino 33 IoT can be found either in the “Examples”
menu in the Arduino IDE or in the “Documentation” section of the Arduino Pro
website [4]
Online Resources
Now that you have gone through the basics of what you can do with the board
you can explore the endless possibilities it provides by checking exciting
projects on ProjectHub [5], the Arduino Library Reference [6] and the online
store [7] where you will be able to complement your board with sensors,
actuators and more
Board Recovery
All Arduino boards have a built-in bootloader which allows flashing the board
via USB. In case a sketch locks up the processor and the board is not
reachable anymore via USB it is possible to enter bootloader mode by double-
tapping the reset button right after power up.
Connector Pinouts
USB
Pin | Function | Type | Description |
---|---|---|---|
1 | VUSB | Power | Power Supply Input. If board is powered via VUSB from header |
this is an Output
(1)
2| D-| Differential| USB differential data –
3| D+| Differential| USB differential data +
4| ID| Analog| Selects Host/Device functionality
5| GND| Power| Power Ground
- The board can support USB host mode only if powered via the VUSB pin and if the jumper close to the VUSB pin is shorted.
Headers
The board exposes two 15 pin connectors which can either be assembled with pin
headers or soldered through castellated vias.
Pin | Function | Type | Description |
---|---|---|---|
1 | D13 | Digital | GPIO |
2 | +3V3 | Power Out | Internally generated power output to external devices |
3 | AREF | Analog | Analog Reference; can be used as GPIO |
4 | A0/DAC0 | Analog | ADC in/DAC out; can be used as GPIO |
5 | A1 | Analog | ADC in; can be used as GPIO |
6 | A2 | Analog | ADC in; can be used as GPIO |
7 | A3 | Analog | ADC in; can be used as GPIO |
8 | A4/SDA | Analog | ADC in; I2C SDA; Can be used as GPIO (1) |
9 | A5/SCL | Analog | ADC in; I2C SCL; Can be used as GPIO (1) |
10 | A6 | Analog | ADC in; can be used as GPIO |
11 | A7 | Analog | ADC in; can be used as GPIO |
12 | VUSB | Power In/Out | Normally NC; can be connected to VUSB pin of the USB |
connector by shorting a jumper
13| RST| Digital In| Active low reset input (duplicate of pin 18)
14| GND| Power| Power Ground
15| VIN| Power In| Vin Power input
16| TX| Digital| USART TX; can be used as GPIO
17| RX| Digital| USART RX; can be used as GPIO
18| RST| Digital| Active low reset input (duplicate of pin 13)
19| GND| Power| Power Ground
20| D2| Digital| GPIO
21| D3/PWM| Digital| GPIO; can be used as PWM
22| D4| Digital| GPIO
23| D5/PWM| Digital| GPIO; can be used as PWM
24| D6/PWM| Digital| GPIO, can be used as PWM
25| D7| Digital| GPIO
26| D8| Digital| GPIO
Pin| Function| Type| Description
---|---|---|---
27| D9/PWM| Digital| GPIO; can be used as PWM
28| D10/PWM| Digital| GPIO; can be used as PWM
29| D11/MOSI| Digital| SPI MOSI; can be used as GPIO
30| D12/MISO| Digital| SPI MISO; can be used as GPIO
Pin| Function| Type| Description
---|---|---|---
1| +3V3| Power Out| Internally generated power output to be used as voltage
reference
2| SWD| Digital| SAMD11 Single Wire Debug Data
3| SWCLK| Digital In| SAMD11 Single Wire Debug Clock
4| UPDI| Digital| ATMega4809 update interface
5| GND| Power| Power Ground
6| RST| Digital In| Active low reset input
Mechanical Information
Board Outline and Mounting Holes
The board measures are mixed between metric and imperial. Imperial measures
are used to maintain a 100 mil pitch grid between pin rows to allow them to fit
a breadboard whereas board length is Metric.
Connector Positions
The view below is from top however it shows Debug connector pads which are on
the bottom side. Highlighted pins are pin 1 for each connector’
Top view
Certifications
Declaration of Conformity CE DoC (EU)
We declare under our sole responsibility that the products above are in
conformity with the essential requirements of the following EU Directives and
therefore qualify for free movement within markets comprising the European
Union (EU) and European Economic Area (EEA).
Declaration of Conformity to EU RoHS & REACH 211 01/19/2021
Arduino boards are in compliance with RoHS 2 Directive 2011/65/EU of the
European Parliament and RoHS 3 Directive 2015/863/EU of the Council of 4 June
2015 on the restriction of the use of certain hazardous substances in
electrical and electronic equipment.
Substance | Maximum limit (ppm) |
---|---|
Lead (Pb) | 1000 |
Cadmium (Cd) | 100 |
Mercury (Hg) | 1000 |
Hexavalent Chromium (Cr6+) | 1000 |
Poly Brominated Biphenyls (PBB) | 1000 |
Poly Brominated Diphenyl ethers (PBDE) | 1000 |
Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
Benzyl butyl phthalate (BBP) | 1000 |
Dibutyl phthalate (DBP) | 1000 |
Diisobutyl phthalate (DIBP) | 1000 |
Exemptions : No exemptions are claimed.
Arduino Boards are fully compliant with the related requirements of European
Union Regulation (EC) 1907 /2006 concerning the Registration, Evaluation,
Authorization and Restriction of Chemicals (REACH). We declare none of the
SVHCs (https://echa.europa.eu/web/guest/candidate-list-table), the Candidate
List of Substances of Very High Concern for authorization currently released
by ECHA, is present in all products (and also package) in quantities totaling
in a concentration equal or above 0.1%. To the best of our knowledge, we also
declare that our products do not contain any of the substances listed on the
“Authorization List” (Annex XIV of the REACH regulations) and Substances of
Very High Concern (SVHC) in any significant amounts as specified by the Annex
XVII of Candidate list published by ECHA (European Chemical Agency) 1907
/2006/EC.
Conflict Minerals Declaration
As a global supplier of electronic and electrical components, Arduino is aware
of our obligations with regards to laws and regulations regarding Conflict
Minerals, specifically the Dodd-Frank Wall Street Reform and Consumer
Protection Act, Section 1502. Arduino does not directly source or process
conflict minerals such as Tin, Tantalum, Tungsten, or Gold. Conflict minerals
are contained in our products in the form of solder, or as a component in
metal alloys. As part of our reasonable due diligence Arduino has contacted
component suppliers within our supply chain to verify their continued
compliance with the regulations. Based on the information received thus far we
declare that our products contain Conflict Minerals sourced from conflict-free
areas.
FCC Caution
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
-
This device may not cause harmful interference
-
this device must accept any interference received, including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.
- This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
User manuals for license-exempt radio apparatus shall contain the following or equivalent notice in a conspicuous location in the user manual or alternatively on the device or both. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference
- this device must accept any interference, including interference that may cause undesired operation of the device.
IC SAR Warning:
This equipment should be installed and operated with minimum distance 20 cm
between the radiator and your body.
Important: The operating temperature of the EUT can’t exceed 85℃ and shouldn’t be lower than -40℃. Hereby, Arduino S.r.l. declares that this product is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU. This product is allowed to be used in all EU member states.
Frequency bands | Maximum output power (EIRP) |
---|---|
2402-2480MHz(EDR) | 6.24 dBm |
2402-2480MHz(BLE) | 6.30 dBm |
2412-2472MHz(2.4G WiFi) | 13.61 dBm |
Company Information
Company name | Arduino S.r.l |
---|---|
Company Address | Via Andrea Appiani,2520900 MONZA |
Reference Documentation
Reference | Link |
---|---|
Arduino IDE (Desktop) | https://www.arduino.cc/en/Main/Software |
Arduino IDE (Cloud) | https://create.arduino.cc/editor |
Cloud IDE Getting Started |
https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with-
arduino- web-editor-
4b3e4a
Forum| http://forum.arduino.cc/
SAMD21G18| http://ww1.microchip.com/downloads/en/devicedoc/40001884a.pdf
NINA W102| https://www.u-blox.com/sites/default/files/NINA-
W10DataSheet%28UBX-
17065507%29.pdf
ECC608| http://ww1.microchip.com/downloads/en/DeviceDoc/40001977A.pdf
MPM3610|
https://www.monolithicpower.com/pub/media/document/MPM3610_r1.01.pdf
NINA Firmware| https://github.com/arduino/nina-fw
ECC608 Library| https://github.com/arduino-libraries/ArduinoECCX08
LSM6DSL Library| https://github.com/stm32duino/LSM6DSL
ProjectHub|
https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending
Library Reference| https://www.arduino.cc/reference/en/
Arduino Store| https://store.arduino.cc/
Revision History
Date | Revision | Changes |
---|---|---|
04/15/2021 | 1 | General datasheet updates |
References
- Arduino Project Hub
- Arduino Project Hub
- Arduino Project Hub
- GitHub - arduino-libraries/ArduinoECCX08
- GitHub - arduino/nina-fw: Firmware for u-blox NINA W102 WiFi/BT module
- GitHub - stm32duino/LSM6DSL: Arduino library to support the LSM6DSL 3D accelerometer and 3D gyroscope
- Arduino Official Store | Boards Shields Kits Accessories
- Software | Arduino
- Arduino Reference - Arduino Reference
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>