PHILIPS BDS562 Copenhagen LED and City Gen2 Instruction Manual

: June 9, 2024
: Philips

Table of Contents

PHILIPS BDS562 Copenhagen LED and City Gen2
Product Information
Technical Specifications
Features
Product Usage Instructions
Installation
Usage
Setting
Disconnect before servicing
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PHILIPS BDS562 Copenhagen LED and City Gen2

Product Information

The product is a range of outdoor LED luminaires manufactured by Philips Lighting. The range includes BDS5 6 2, BRS5 6 2, BSS5 6 2, BDS7 6 2, BRS7 6 2, and BSS7 6 2 models. The luminaires come with different LED modules that range from LED40 to LED200. The product has an IP66 rating, which means it is protected against dust and heavy water jets. It also has an IK07 rating, which means it has moderate impact resistance.

Technical Specifications

Power supply: 220V outdoor / 240V
Frequency: 50Hz / 60Hz
Inrush current: +/-10%
Energy class of the light source: 8
Max number of luminaires on MCB 16A type B with resp FP/SR
driver: varies depending on the model and LED module

Features

Asymmetric and symmetric light distribution
Top or side entry pipe thread
Suspended/wire installation option

Product Usage Instructions

The outdoor LED luminaires can be used for various applications, such as street lighting, parking lots, and public spaces. Follow the instructions below to properly install and use the product:

Installation

Make sure the power supply is turned off before installation.
Select an appropriate mounting location that is secure and has proper drainage.
If using a pole, make sure it is strong enough to support the weight of the luminaire.
Use appropriate tools to connect the luminaire to the power supply and mount it securely.
If using the wire installation option, make sure the wires are properly connected and secured.
Follow local regulations and standards for outdoor lighting installation.

Usage

Turn on the power supply and check that the luminaire is working properly.
Adjust the luminaire as needed to achieve the desired light distribution.
Regularly inspect and clean the luminaire to maintain optimal performance.
Replace any damaged parts or components immediately.
Follow local regulations and standards for outdoor lighting usage.

Setting

Disconnect before servicing

Luminaire has basic insulation between Low Voltage supply and control conductors.
The light source and/or control gear and/or the external flexible cable contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similarly qualified person.
GB Storage, installation, use, operation and maintenance of the products needs to be performed exactly according the instructions in this manual and/or other instructions as may be provided by us to guarantee safe use of the product over its entire lifetime. Failure to adhere to these instructions will invalidate your entitlement to warranty. Bolts with an indication of torque strength on the drawing need to be tightened using a calibrated torque wrench. Pre-assembled bolts need to be retightened again to the required torque specification to assure maximum strength over a lifetime.
GB Zhaga-D4i and SR certified compatibility – For Zhaga-D4i/SR-Certified based luminaires only Zhaga-D4i/SR-Certified components/sensors are to be used (see also: https://www.zhagastandard.org/products/ https://www.lighting.philips.co.uk/oem-emea/products/driving-connected-lighting). The functional compatibility of two SR-certified and/or Zhaga-D4i controllers/sensors to be used in combination, as well as the override possibility of any line-switch function used in an SR-based/Zhaga-D4i luminaire, is to be released by the master controller/sensor supplier. If using a NEMA 7-pin socket on an SR-based luminaire, a full system verification is required. Not following this advice can/will cause risk of damage and non-compliance for which Signify cannot take any responsibility.

© 2020 Signify Holding
All rights reserved. This document contains information relating to the product portfolio of Signify which information may be subject to change. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V.. All other trademarks are owned by Signify Holding or their respective owners.
Signify Holding
The Netherlands