Retro Sound Redondo RT Dodge Dart Redondo Thumb Roller Radio User Guide

: June 9, 2024
: Retro Sound

Table of Contents

Retro Sound Redondo RT Dodge Dart Redondo Thumb Roller Radio
Product Information
What’s in the Box
Installation
Control Layout
Basic Operation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Retro Sound Redondo RT Dodge Dart Redondo Thumb Roller Radio

Product Information

Radio Motor with Thumb-Roller Controls
The Radio Motor with Thumb-Roller Controls is a modern sound system designed to fit in classic cars. It comes with thumb-rollers, hardware, and the InfiniMount Brackets needed for installation. The product also includes a modular cable, preset buttons, and optional hardware for mounting the radio to the dash.

The radio has various control layouts, including basic operation and Redondo mode. It has power on/off, volume, changing source modes, changing radio bands, tune, mute on/off, and equalizer (EQ) controls. The radio also has a clock setting that can be adjusted through the thumb-roller controls.

The Thumb-Roller Quick Start Guide provides installation instructions and comprehensive instructions for using the product are included in the user manual included in the motor box or on the manufacturer’s website.

What’s in the Box

Thumb-Rollers

Hardware

$Retro-Sound-Redondo-RT-Dodge-Dart-Redondo-Thumb-Roller-Radio- $2$$

Installation

Attach each InfiniMount Bracket to the Radio Motor with the eight small screws.
Insert the Thumb-Rollers into the InfiniMount Brackets. Gently push to snap into place. $Retro-Sound-Redondo-RT-Dodge-Dart-Redondo-Thumb-Roller-Radio- $4$$
Complete the installation by plugging one end of the modular cable into the left Thumb-Roller and the other end of the modular cable into the left side of the Radio Motor. Then, repeat for the right Thumb-Roller on the right side. Use the optional hardware (if needed) to help mount the radio to the dash. $Retro-Sound-Redondo-RT-Dodge-Dart-Redondo-Thumb-Roller-Radio- $5$$

Control Layout

$Retro-Sound-Redondo-RT-Dodge-Dart-Redondo-Thumb-Roller-Radio- $6$$

Redondo Mode
The following steps must be performed to set up the Radio Motor to function with the Redondo Thumb-Roller controls. Press and hold the Left-Inside Thumb- Roller(1) for approximately 15 seconds to reboot the radio into SEL PANEL mode. While holding the Power Button the unit will display the following sequence: RETROSOUND>RADIO>GOODBYE>TIME DISPLAY>SEL PANEL, continue holding the thumb-roller until SEL PANEL is displayed. Once SEL PANEL is displayed release the Left-Inside Thumb-Roller(1) and immediately press and release the Left- Inside Thumb-Roller (1) to cycle through the choices until REDONDO appears. The Display will Flash REDONDO 5 times and will turn off. Your Radio Motor is now configured to work with your selected face.

Radio Presets

Setting Radio Presets
To set a preset, tune to the station you want to set the preset to, and then press and hold the desired Preset Button(5) for two seconds.
Recalling Radio Presets
To recall a preset, simply press the Preset Button(5) your station was set to previously.

Basic Operation

To power on/off the unit, press and hold the Left-Inside Thumb-Roller(1).
To adjust the volume, rotate the Left-Outside Thumb-Roller(2) up or down.
To change source modes, rotate the Left-Inside Thumb-Roller(1) down.
To change radio bands, rotate the Right-Inside Thumb-Roller(3) up.
To tune to a station, rotate the Right-Outside Thumb-Roller(4).
To mute on/off, press the Right-Outside Thumb-Roller(4).
To adjust the equalizer (EQ), press the Left-Outside Thumb-Roller(2) to enter the Tone Control sub-menu. Press and release the Left-Outside Thumb-Roller(2) until you see the EQ setting you’d like to adjust. Rotate the Left-Outside Thumb-Roller(2) up or down to adjust the setting. Press the Left-Outside Thumb-Roller(2) to move to the next item, and repeat to adjust each option. Let the unit time out to set.

Power On/Off
Press the Left-Inside Thumb-Roller(1) to power the unit on. Press and hold the Left-Inside Thumb-Roller(1) to power the unit off.
Volume
Rotate the Left-Outside Thumb-Roller(2) up or down to change the volume.
Changing Source Modes
Rotate the Left-Inside Thumb-Roller(1) down to cycle through the source modes.
Changing Radio Bands
Rotate the Right-Inside Thumb-Roller(3) up to cycle through the radio bands.
Tune
Rotate the Right-Outside Thumb-Roller(4) to scroll through the stations.
Mute On/Off
Press the Right-Outside Thumb-Roller(4) to mute and unmute.
Equalizer (EQ)
Press the Left-Outside Thumb-Roller(2) to enter the Tone Control sub-menu. Press and release the Left-Outside Thumb-Roller(2) until you see the EQ setting you’d like to adjust. Rotate the Left-Outside Thumb-Roller(2) up or down to adjust the setting. Press the Left-Outside Thumb-Roller(2) to move to the next item, and repeat to adjust each option. Let the unit time out to set.
Setting the Clock
Press and hold the Right-Inside Thumb-Roller(3) to enter the System Settings sub-menu. Rotate the Right-Outside Thumb-Roller(4) to cycle through the choices until you see CLK, then press the Right-Outside Thumb-Roller(4) to select. Rotate the Right-Outside Thumb-Roller(4) up or down to adjust the hours. Then press the Right-Outside Thumb-Roller(4) again to move on to minutes. Rotate the Right-Outside Thumb-Roller(4) up or down to adjust the minutes. Let the unit time out to setup .
**Display Color***
Press and hold the Right-Inside Thumb-Roller(3) to enter the System Settings sub-menu. Rotate the Right-Outside Thumb-Roller(4) to cycle through the choices until you see SCAN, then press the Right-Outside Thumb-Roller(4) to cycle through the colors. Let the unit time out to set.
Beep On/Off
Press and hold the Right-Inside Thumb-Roller(3) to enter the System Settings sub-menu. Rotate the Right-Outside Thumb-Roller(4) to cycle through the choices until you see BEEP ON/OFF, then press the Right-Outside Thumb- Roller(4) to choose between BEEP ON or BEEP OFF. Let the unit time out to set.