beamZ Pro SP420IP Stage Blinder User Manual

Pro SP420IP Stage Blinder User Manual

SAFETY INSTRUCTIONS

WARNING!
Before carrying out any operations wAh the unit carefully read this instruction manual and keep A wAh ore fa- future reference k contains important information about the installation. usage a nd maintenance of the unit • Unpack and check carefully that there is no transportation damage before using the unA • Please read these instructions carefully and follow the instructions • Observe all safety warnings. Never remove sa fety warningsorother information from the equipment. • Be sure that no venti lotion slots are blocked: otherwise the tuna will overheated

WARNING! Before commenting the equipment to the power outlet first verify that the mains voltage and frequency match the values specified on the equipment If the equipment has a voltage selection swatch. corned the equipment to the power outlet only if the equipment values and the mains power values match. If the included power cord or power adapter does not  in your wall outlet. contact your electrician.

• After connecting the unit check all cables in order to prevent damage or accidents. eg. due to tripping hazards Make sure that the power cord is never crimped or damaged. Check the und and the power cord from time to time
• Always disconnect power from the mains. when unit is not used or before deafeningly handle the power cord by the plug. Never pull out the plug by tugging the power cord. • Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning before extended periods of disuse.
• Do not width the unit on and off in short intervals.
• Do not connect the uni to a dimmer pack
• Install the unit in a well ventilated place
• Never place any material over the lens
• Never let the sunlight lights directly to the front lens. even when the uni snot working.
• Always allow free air space of at least 50 an around the uni for ventilation.
• Make sure that the area Beebe the installation place is blocked when rigging. derigging or servicing the unit
• For mounting height >100 cm. always fix the und haw an appropriate safety-rope.F& the salty-rope at the corned ligation points only. The safety-rope must never behind at the transport handles!
• Never look diredly at the light beam. Plea se note that fast Manges in fighting. e g flashing light. may trigger epileptic seizures in photo sens Ae persons or personswAh epilepsy.
• This uni is not designed for permanent operation Consistent operation breaks will ensure that the unit will serve you for a long time without defects

WARNING! If the power cord of the unit is equipped with an earthing contact then it must be connected to an outlet with a protective ground Never deactivate the protective ground of a power cord.

• Make sure that the wit is not exposed to extreme heat. moisture or dust.
• Clean the unit using dry cloth.
• Do not touch the unaware-handed during As operation (housing becomes very hot). Allow the wit to cool for at least 5 minutes before handling.
• This und is designed elusively for indoor use do not use this equipment in the immediate vicindy of fluid (does not apply to special outdoor equipment – in this case. observe the special instructions noted below l Do not expose this unit to flammable materials fluids or gases
• If the und has been exposed to drastic temperature fluctuation kg after transportation l do not swatch f on immediately. The arising condensation water might damage your unit Leave the unit switched off until A has reached room temperature
• Never attempt to bypass the thermostatic switch or fuses.
• Do not dismantle or modify the unit.
• For replacement use fuses/bulb of sane type and rating only.
• Repairs. servicing and electric connection must be carried out by a qualified technician.
• The ambient temperature must always be between -5° C and +45° C.
• If this unit is operated in any other way. than the one descnbed in this manual, the product may suffer damages and the warranty becomes void
• Plastic bags must be kept out of reach of children.
• link must be installed out of the reach of children. Never leave the unit running unattended.

This symbol on the product or an As packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the app ko ble collection point for the recycling of drivelled and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health. which could otherwise be caused by inappropriate waste handing of this product. The receding of materials will help to conserve natural resources For more detailed information about recycling of this product. please onto d your loo I Civic Office. your household waste disposal service or the shop where you purchased the product

UNPACKING INSTRUCTION

CAUTION! Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, Land have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the Factory, it is important that the product be returned in the original Factory box and packing. If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.
POIAERSUPPLY
On the label on the backside of the unit is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all other voltages than specified, the light effect can be irreparably damaged. The product must also be directly connected to the mains and may be used. No dimmer or adjustable power supply. **WARNING! Always conned the unit to a protected circuit (circuit breaker or Fuse). Make sure the unit has an appropriate electrical ground to avoid the risk of electrocution or fire.
RIGGING**
The unit may be set up on a stable and even surface. By means oF the Fixing facilities of the baseplate, the unit can also be mounted upside down to a truss, see below picture. For fixing, certified clamps with correct save working load are required. According to the figure, the quick lock bolts of the omega brackets are placed into the openings provided in the base plate and turned clockwise until they lock (to the stop). The mounting place must be of sufficient stability and be able to support a weight of 10 times oF the unit’s weight. Secure the unit with a safety cable so that it cannot fall down.
When carrying out any installation, always comply European and national guidelines concerning rigging, truss and all other safety issues. Always let the installation checked out by an authorized dealer !

DMX512 CONTROL

CAUTION At the last unit, you must close the DMX line with a terminating resistor. Take an XLR connector and solder a 120 Ohm resistor between signal (-) and signal (+) and connect it to the DMX output of the last unit in the line.

ROM CONTROL

This unit can communicate using RDM (Remote Device Management) via DMX512. RDM is a bi-directional communication protocol for use in DMX512 control systems, it is the open standard for DMX512 configuration and status monitoring. The RDM protocol allows data packets to be inserted into a DMX512 line without affecting the existing non-RDM equipment. The system allows a controller or special ROM controller to send and receive commands from specific fixtures. The RDM function allows you, for example to remotely set the DMX start address of your fixtures. This is especially useful when the fixture is installed in an inaccessible location. Each unit has an ROM UID (unique identification number).
PROTECTION CLASS IP65
Units with protection class IP65 are dust-tight and completely protected against contact (first code number). They are also protected against splash water from any angle (second code digit). That is why this unit can also be used out- doors. Events units are generally only designed for temporary use however (event lighting) and not for permanent use outdoors. The specified protection class does not make a statement about the weather resistance of the units (resistance to changing ambient conditions as well as against the effects of sunlight and UV rays). The seals and screw connections of the units must be checked regularly to ensure a fault-free operation.

MAINTENACE

This unit is virtually maintenance-free, but you should check the unit regularly for mechanical and electrical aspects. Assess the operating environment and establish an inspection and cleaning schedule that follows the guidelines below:

• Disconnect the unit from the power supply and allow it to cool completely before inspecting and cleaning.
• Check that the screws and bolts used to install the unit are securely tightened and free from corrosion.
• Check the housing, fixing points and installation points, they must not show any signs of deformation, wear or fatigue.
• Check the mechanically moving parts, these must not show any signs of wear or fatigue.
• Check the electrical power and signal cables, they must not show any damage or fatigue.
• Do not use solvents, abrasives or other aggressive products to clean the unit.
• Wipe the unit and clean the glass plate with a soft, clean, lint-free cloth moistened with a weak cleaning solution. Place the solution on the cloth and not on the surface to be cleaned. Avoid rubbing glass surfaces.
• Dry the unit, connectors and contacts with a soft, clean, lint-free cloth or low-pressure compressed air before re-powering the unit.

TROUBLE SHOOTING

The checklist below may help you troubleshoot in the unlikely event that a problem occurs while using the product:

that power is turned on. Check cables and connections.
Replace mean fuse or contact Beamz support or Beamz authorized service partner. Do not remove base or yoke covers. Do not attempt to replace a fuse or carry out any repairs or service that are not described in this User Manual unless you have both authorization from Beamz support or Beamz authorized service partner.
Unit resets correctly but does not respond (or does not respond correctly) to the controller.| The controller is not connected. Bad OMX-line.
DMX-line has no end resistance.
Incorrect unit addressing.
A unit is defective and is disturbing data transmission on the DMX-line.
Pin 2 and 3 are reversed in XLR connection.| Conned controller.
Inspect connections and cables. Correct poor connections. Repair or replace damaged cables. Insert DMX terminator plug in OMX output socket of last unit on OMX-line. Check unit address and OMX mode settings. Unplug DMX IN and OUT connectors and connect them directly together to bypass one unit at a time until normal operation is regained. Have defective unit serviced by an authorized technician. Inspect connections and cables. Install a phase- reversing cable between the units or swap pin 2 and 3 in the unit that behaves erratically.
Error after unit reset.| Effect requires mechanical adjustment.| Check unit’s software version and error messages for more information. Contact Beamz support or Beamz authorized service partner.
Light output cuts out intermittently.| Unit too hot. LEDs damaged.
The power supply settings do not match local AC voltage and frequency.| Allow unit to coot Reduce ambient temperature. Ensure free airflow around unit. Clean unit if necessary. Disconnect unit and contact Beamz support or Beamz authorized service partner. Disconnect unit Check settings and
correct if necessary.

CONTROL MENU

DMX CHANNELS

1 CHANNELS

3 CHANNELS

5 CHANNELS

9 CHANNELS

TECHNICAL SPECIFICATIONS

Design and product specifications are subject to change without prior notice.
The products referred to in this manual is conforming European and UK legislation directives to which they are subject:

Tronios B.V.,
Bedrijvenpark Twente Noord 18,
7602KR Almelo, The Netherlands| Tronios Ltd.,
130 Harley Street,
London W1G 7JU, United
Kingdom
2014/35/EU
2014/30/EU
2011/65/EC| S.I. 2016:1101
S.I. 2016:1091
S.I. 2012:3032

offers a wide range of high performance lighting equipment and related accessories for the rental, entertainment and architectural lighting markets. BeamZ Pro stands for performance, innovation and value pricing!

BEAMZLIGHTING.COM

Documents / Resources

| beamZ Pro SP420IP Stage Blinder [pdf] User Manual
150.455, SP420IP, SP420IP Stage Blinder, Stage Blinder
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>