SHOGUN EBX5 Electric Mountain Bike Owner’s Manual

: June 9, 2024
: SHOGUN

SHOGUN EBX5 Display Owner’s Manual

EBX5

Appearance and outline

This production is a combination of mental bottom base and glass cover. Usually can work at environment temperature from -20℃ to 60℃
Size (Unit: mm)

Appearance and outline

Note: the buttons has cable connecting with the display.

Power
Adding +
Minus –
Light
Walking assistant

Product Functions

This production can show contents enclose

Battery capacity
Speed
Miles (single trip and total)
Single trip riding period
Pas level
Light on/ off
Walking assistant
Error code
Riding mode
Parameter: wheel size, speed limitation, backlight, pas level, pas default data, unit, ISO
Adjustment of backlight brightness

Display Area

Installation

Please fix the product on the handlebar and connect cable well. Do not connect cable when battery on.

Remark: Locking the remote support should be careful and it is easy broken over one certain Nm.

Operation Introduction

Turn On/ Off

Pressing “power” button over 3 seconds and turn-on the system, vice versa, pressing same button over 3 seconds can turn-off the system.

Speed & Distance

After turning on system, the product will show current speed and distance; one-click “power” button will show different content like current speed, total distance- average speed, single trip- max speed, and single trip period. See 6.8 to reset the trip.

Speed and Distance

Light On/ Off

Long press “light” button can turn on/off the light.

Walking Assistant

Long press and hold the “walking assistant” button will provide walking assistant function.

Pas Level Adjustment

Press “adding” or “minus” can change pas level among “0~5”, “5” is max. The default starting pas is “1”.

Battery Capacity

The battery icon has 5 sections to show capacity, showing 5 sections means battery is full, and if only lifting last one section will keep shining and warn to recharge.

Battery Capacity

Full Charge Status Low Battery Status Powerless Status

Riding Mode

Pressing “walking assistant” button can change riding mode sequence, T (Tour) -S (Sport) -C（Customized）-E（Eco）-T（Tour）.

REMARK ： Some version cancel this function and not show T (Tour) （Customized）-E（Eco）-T（Tour）.

Riding Mode

Brightness Adjustment

The product can auto-adjust brightness and light on/off according to the environment under auto mode. Long press the “light” button can turn off the auto function. Restart system will turn on the auto function again.

Error Code

Error Code List

Settings

When speed is 0, long press “adding” and “minus” together will enter setting mode 1, press “power” button can adjust “backlight brightness”, “wheel size”, “metric-inch conversion”. Long press “adding” and “minus” again immediately after entering setting mode 1 will enter into setting mode 2, can adjust “pas level”, “default pas”, “light sensor”.

Turn On/ Off

BL means backlight, can adjust “1~3” level, “1” is low, “2” is middle and “3” is high, default is “1”, press “adding” and “minus” can adjust and “power” button can save the change and enter next setting.

Backlight setting

Wheel Size

Press “adding” or “minus” can change wheel size like 16inch, 18 inch, 20inch, 22inch, 24inch, 26inch, 700C, 28inch, and 29inch, press “power” button can save the change and enter next setting.

Wheel Size setting

Speed Limit

Speed limit function can set max assistant speed, system will stop assistant if over speed limit to protect the driver. User can set speed limit from 12 Km/h to 40 Km/h, and the default value is 25 Km/h. Press “adding” and “minus” button can change value and press “power” button to save and enter next setting.

Speed limit setting

Unit Setting

User can have “matric-inch conversion” change the unit between “Km/h” and “MPH” by pressing “adding” or “minus” , and press “power” to save and quit setting.

Unit setting

Pas Setting

Pas ranging including 0-3, 1-3, 0-5, 1-5, 0-7, 1-7, 0-9, and 1-9, default is 0-5. Press “adding” and “minus” button can change value and press “power” button to save and enter next setting.

Pas setting

Pas Default Value

Pas default value including 0, 1, 2, and 3, default is 1. Press “adding” and “minus” button can change value and press “power” button to save and enter next setting.

Pas default Value

Light Sensor Value

“P” is light sensor value, the bigger the less sensitivity, which means less requirement on the environment light to auto turn on the light. Press “power” to save and quit setting.