SUNELL SN-IPV57 80HDR Fisheye Network Camera User Guide

: June 9, 2024
: SUNELL

SUNELL SN-IPV57 80HDR Fisheye Network Camera

Panorama Fisheye Network Camera

Quick Setup Guide

NO:101-100-0373-03
Issue:1.4

Precautions

Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip “You have entered the area of electronic surveillance” in an eye-catching place. Failure to correctly use electrical products may cause fire and severe injuries.

WARNING| It alerts you to moderate dangers which, if not avoided, may cause minor or moderate injuries.
---|---
CAUTION| It alerts you to risks. Neglect of these risks may cause device damage, data loss, device performance deterioration, or unpredictable results.
NOTE| It provides additional information.

WARNING

Strictly observe installation requirements when installing the device. The manufacturer shall not be held responsible for device damage caused by users’ non-conformance to these requirements.
Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged.
Use accessories delivered with this device. The voltage must meet input voltage requirements for this device.
If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out.
When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device.
Do not focus strong light (such as lighted bulbs or sunlight) on this device. Otherwise, the service life of the image sensor may be shortened.
If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage.

CAUTION

Avoid heavy loads, intensive shakes, and soaking to prevent damages during transportation and storage. The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart.
Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks.
Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.
Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device.
Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.
Keep the device away from moist, dusty, extremely hot or cold places, or places with strong electric radiation.
If the device is installed outdoors, take insect- and moisture-proof measures to avoid circuit board corrosion that can affect monitoring.
Remove the power plug if the device is idle for a long time.
Before unpacking, check whether the fragile sticker is damaged. If the fragile sticker is damaged, contact customer services or sales personnel. The manufacturer shall not be held responsible for any artificial damage of the fragile sticker.

Special Announcement

All complete products sold by the manufacturer are delivered along with nameplates, quick setup guide and accessories after strict inspection. The manufacturer shall not be held responsible for counterfeit products.
The manufacturer will update this manual according to product function enhancement or changes and regularly update the software and hardware described in this manual. Update information will be added to new versions of this manual without prior notice.
This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product, the final interpretation of company is as a standard.
This manual is only for reference and does not ensure that the information is totally consistent with the actual product. For consistency, see the actual product.

NOTE
For more information, please refer to website.

1 Open Package Examination

Open the package, check the appearance of product for no obvious damage, and confirm the item list for table 1-1 is consistent.

Table 1-1 Packing list

Component

| Quantity|

Remark

---|---|---
Panorama Fisheye Network Camera|

1

|
Quick Setup Guide|

1

|
Installation location sticker|

1

|
T15 Screw driver|

1

|
Plastic anchor φ5.6×29mm|

4

|
Black stainless self-tapping screw
PA4.0×30mm|

4

|
Network access port protective cover|

1

|
Waterproof rubber seal|

1

|
Terminal block|

2

|

2 Device Structure

2.1 Device Ports

NOTE
Different devices may have different ports and multi-head cables; Please refer to the actual product.

Figure 2-1 Hardware ports

Table 2-1 Hardware ports description

ID

| Port Name|

Description

---|---|---

1

| NIC indicator| When there is a network activity, the indicator flashes.

2

| Power supply indicator| The indicator on when connect to the power supply.

3

| SD card indicator| Indicate the card status, the status is described as follows:

Off: No card is inserted
On: A SD card is inserted.

4

| Reset button| Restore the camera to the factory settings by pressing and holding this button for more than five seconds.

5

| SD card slot| Install a SD card.

NOTE

Before install a SD card, verify the card not in write protection state.
Before remove the SD card. Verify the card not in write protection state.
Otherwise, the data may be lost, or the SD card may be damaged.
Before installing or removing a SD card when the camera is running, stop video recording first.

Figure 2-2 Multi-head cable

SUNELL SN-IPV57 - Figure 2-2

Table 2-2 Multi-head cable description

ID

| Core| Description|

Remark

---|---|---|---

1

| Network access port| Connect to a standard Ethernet cable.|

2

| Audio input port| Receive an analog audio signal from devices such as a sound pickup device. | Applied for camera with audio function

3

| Audio output port| Connect to an external audio device such as a speaker.

4

| Power supply (DC 12V) | Connect to a 12V(-15%-+10% ) direct current (DC) power supply.|

5

2.2 Camera Dimensions

NOTE
Different devices may have different dimensions; Please refer to the actual product.

Figure 2-3 Dimensions (Unit: mm)

SUNELL SN-IPV57 - Figure 2-3

3 Device Installation

You can install the fisheye network camera in the ceiling and wall. This section describes how to install the camera in the ceiling.

3.1 Installation Steps

Step 1 Stick the Installation location sticker on the Installation surface, drill four holes based on the marks on the sticker. Drive the plastic anchors into the holes.
Step 2 Take out the camera and remove the installation bracket, use screws with a length of 30mm to fix the installation bracket, as shown in figure 3-1.
Step 3 Connect the multi-connector cable.

NOTE
If you route cables from the top, drill a hole in the surface first. If you route cables from the side, please use the square type junction box or circular junction box, as show in table 3-1.

Step 4 Rotate and remove the decoration, as shown in figure 3-2.

Figure 3-1 Fixing the bracket

Installation Bracket

Figure 3-2 Removing the decoration

decoration

Step 5 Aim the four holes of the camera at the screw bolts, fasten the screws and fix the camera, as shown in figure 3-3.
Step 6 Aim the buckles of the decoration at the chassis gap, push in and rotate the decoration until it can’t rotate, as shown in figure 3-4.

Figure 3-3 Fixing the camera

Figure 3-4 Installing decoration

SUNELL SN-IPV57 - Figure 3-4

3.2 Optional Accessories

The bracket installation may be used in actual installation, the specific optional accessories as shown in figure 3-1.

Figure 3-5 accessories

Cap Wall mount

Match with 3/4″-14 NPS thread

Pendant mount Pole mount Corner mount

Square type junction box Round type junction box

4 Quick Configuration(e.g IE)

Step 1 Open the Internet Explorer, enter the IP address of IP camera (default value: 192.168.0.120) in the address box, and press Enter. The login page is displayed as shown in figure 4-1.
Step 2 Input the user name and password.

NOTE

The default user name is admin. The default password is admin. Change the password when you log into the system for first time to ensure system security.
You can change the system display language on the login page.

Figure 4-1 Login

Step3 Click Login, the main page is displayed.

4.2 Modify IP address

Choose Configuration > Device > Local Network, the Local Network page is displayed.
Enter the IP address in the IP Address box and click Apply as shown in figure 4-2.
After the IP address is set successfully, please use the new IP address to log in the Web interface.

Figure 4-2 Local Network

SUNELL SN-IPV57 - Figure 4-2

4.3 Browsing Video

To ensure the real-time video can be played properly, you must perform the following operation when you log in the web for the first time:

Step 1 the Internet Explorer. Choose Tools > Internet options > Security > Trusted sites > Sites, in the display dialog box, click Add , as shown in figure 4-3.

Figure 4-3 Adding a trusted site

SUNELL SN-IPV57 - Figure 4-3

Step 2 In the Internet Explorer, choose **Tool > Internet Options > Security

Customer level, and set Download unsigned ActiveX control and initialize and script ActiveX controls not marked as safe for scripting under ActiveX controls and plug-ins to Enable** , as shown in figure 4-4.

Figure 4-4 Configuring ActiveX control and plug-in

SUNELL SN-IPV57 - Figure 4-4

Step 3 Download and install the player control as prompted.

NOTE
If the repair tips displayed when installing the control, please ignore the prompt, and continue the installation, the login page is displayed when the control is loaded.

To browse a real-time video, click Live Video. The Live Video page is displayed, as shown in figure 4-5.

Figure 4-5 Live Video

SUNELL SN-IPV57 - Figure 4-5

Click to choose the fish eye modes, as shown in following figure.

Ceiling Mode

SUNELL SN-IPV57 - Ceiling Mode

Mode

| Description| Mode|

Description

---|---|---|---
| Fisheye view| | Live view with a fisheye view and 3 PTZ view
| Live view with a fisheye view and 8 PTZ view| | Live view with 4 PTZ view
| Live view with 2 PTZ view| | 180 degrees panorama view
| 360 degrees panorama view| | Live view with a panorama view and 1 PTZ view
| Live view with a panorama view and 3 PTZ view| | Live view with a panorama view and 6 PTZ view
| Live view with a panorama view and 8 PTZ view| | Live view witha panorama view, a fisheye and1 PTZ view

Wall Mode

SUNELL SN-IPV57 - Wall Mode

Table Mode

SUNELL SN-IPV57 - Table Mode

4.4 Fish eye configuration

Choose “Configuration > Device > Fish eye”, The Fish eye configuration page is displayed, set the parameters for “Mount type” and “Fisheye type”as shown in figure 4-6.

Figure 4-6 Fish eye

SUNELL SN-IPV57 - Figure 4-6

Three mount config are supported by the fisheye camera: wall, ceiling, table.

Fish eye: Original 360°, surround image;
Double panorama: Double 180° panoramic image;
4PTZ: De-warping quad image.
Single panorama: Single 180° panoramic image;
Fisheye+3PTZ: 360° surround+3 De-warping images.

4.5 Two-way audio

NOTE
Partial cameras do not support two-way audio, this section do not apply.

4.5.1 Camera PC
Connection:
Step 1 Connect microphone to audio input interface of camera.
Step 2 Connect speaker to the PC audio output interface.
Step 3 Log in camera Web, click to turn on two-way audio.

4.5.2 PC Camera
Step 1 Connect microphone to PC audio input interface.
Step 2 Connect speaker to camera audio out interface.
Step 3 Log in camera Web, click to turn on two-way audio.

4.6 Alarm Configuration

NOTE
Partial camera do not support alarm, this section do not apply.

Alarm input and Alarm output connection:
Step 1 Connect alarm input device to Alarm IN0 and Alarm COM0 of multi-head cable.
Step 2 Connect alarm output device to Alarm OUT1 and Alarm COM1 of multi-head cable, alarm output interface can connect to normal open device only.
Step 3 Log in Web, Choose Configuration > Alarm > Alarm Output, set the parameters as shown in figure 4-6.
Step 4 Choose Configuration > Alarm >I/O Alarm Linkage, enable the I/O Alarm and set the parameters of Schedule Setting.

Figure 4-7 Alarm Output

SUNELL SN-IPV57 - Figure 4-7