Hl ESR3 Electric Scooter Instruction Manual
- June 5, 2024
- RBO
Table of Contents
Hl ESR3 Electric Scooter
Description
Installation
Folding
Unfolding your scooter:
Push the hook and lift up the handlebar from the rear fender, then press the
folding lever until you hear the click sound
Folding your scooter:
Push the safety button and pull out the folding lever, then put the handlebar
into the hook on the rear fender
Power:
Turn on/off with pressing the power button for 3 seconds. The speed level will
be “00”, and the LED light is on.
Light:
Lightly turn on/off the front and rear lights with pressing the power button,
the rear light will flash when brake.
Speed:
System will start with max speed 25 KM/H, you can press the power button twice
to switch to second mode max speed 18 KM/H.
Before You RIDE
Please read all instructions carefully before your ride:
- Do not ride in the rain.
- Do not ride on wet floors, potholes, stairs, or any other unsafe surface.
- Please turn off the power when walking with E-scooter.
- Intended for single rider only.
- Maximum rider weight of 100KG.
- Maximum rider height of 200 CM.
- Recommended for use with riders of 16 years of age.
- Please stop use immediately upon damage and contact an authorized dealer
How to begin each ride:
- Please read the owner’s manual and make sure you are wearing the proper safety equipment including a helmet, knee and elbow protection ..
- Turn on the power and push the scooter by kicking to get initial speed.
- Control the speed by using the power control handle to accelerate or brake.
ChARGING
Plug in the charger to the charge port in your E-scooter.
Adjust the hub brake
Specification
E-Scooter
- Rated Power 180/200W
- Battery 25.2V 4AH /36V 4AH
- Charging time 3.5-4 hours
- Range 18km/h 25km/h
- IP Rating I PX4 water-resistant
- Lights Front and Rear LED lights
- Brake system Electronic brake+ Mechanical Hub Brake
- Tire 8.0 ” Semi solid pneumatic
- Maximum speed 25km /h
- Climbing ability degree
- Weight limit 100kg
- temperature 32-104 ° f (0-40 ° C)
- Operating temperature 14-104 ° f (- 10-40 ° C)
The actual achieved by each ride will depend on actual rider weight, road surface, incline, temperature and intensity of acceleration.
Safety and Maintenace
Maintenance:
- Before cleaning the product, be sure to turn off the switch and disconnect the power supply.
- Please clean the product after each use.
- The electric scooter can be wiped with a damp cloth. Do not put the E-scooter into water or other liquids, or wash it under water or other liquids.
- This product should be stored in a clean, dry place out of direct sunlight.
- Before storing the product, make sure it is clean and dry.
Contact information:
- Manufacturer：HL Corp Shenzhen
- Address：The 3rd Industrial Park , Bitou Village Songgang Town ,
- Baoan District , Shenzhen , China.
- Telephone：+86 0755-2713-0185
- Website：http://us.hlcorp.com/contact/
If you experience problems related to riding, maintenance and safety, or if your electric vehicle appears problems, please contact us.
Caution
- Risk of explosion if battery is replaced by an incorrect type in the E-scooter. Dispose of used batteries according to manufacturer instructions and local regulations.
- Do not dispose of the battery into fire or a hot oven or mechanically crushing or dismantling the battery. This can result in fire or explosion.
- Do not leave the battery in high temperature environments that can result in an explosion or the leakage of flammable liquid or gas.
- Do not subject the battery to excessively low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
- This appliance can be used by children aged from 16 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of
- the appliance in a safe way and understand the hazards involved
- Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision the appliance is only to be used with the unit provided
FCC Note
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference
European Union Compliance Statement Battery recyding information for the European Union
Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC concerning batteries and accumulators and waste batteries and accumulators. The Directive determines the framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union. This label is applied to various batteries to indicate that the battery is not to be thrown away, but rather reclaimed upon end of life per this Directive. In accordance with the European Directive 2006/66/EC, batteries and accumulators are labeled to indicate that they are to be collected separately and recycled at end of life. The label on the battery may also include a chemical symbol for the metal concerned in the battery (Pb for lead, Hg for mercury, and Cd for cadmium). Users of batteries and accumulators must not dispose of batteries and accumulators as unsorted municipal waste, but use the collection framework available to customers for the return, recycling, and treatment of batteries and accumulators. Customer participation isimportant to minimize any potential effects of batteries and accumulators on the environment and human health due to the potential presence of hazardous substances. Restriction of Hazardous Substances Directive (RoHS) Radio and Telecommunications Terminal Equipment Directive
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>