PEAKnx YOUVI Basic Lighting Management Software Owner’s Manual
- June 9, 2024
- PEAKnx
Table of Contents
- PEAKnx YOUVI Basic Lighting Management Software Owner’s Manual
- Legal notes
- 1Who is this guide for?
- 2 Recommended procedure for the YOUVI setup
- Recommended procedure: with Windows PC
- Procedure without Windows PC
- 2.1 Installation of the YOUVI Server and Visu on the panel with KNX
- 2.2 Installation of the YOUVI Client and Visu on the Windows PC
- 2.3 Make basic settings in the configuration menu
- 2.1Check the imported project and create additional functions
- 2.1 Optional: Install and set up add-ons
- 2.2Create a server backup
- 2.3 Create the dashboard for the panel
- 2.4 Create a client backup
- 2.5 Transfer the backup to the panel
- 2.6 Create additional dashboards and transfer their backups to additional
- 1Establish a connection to the KNX network
- 4 Remarks on the bus monitor and IP router
- 1 Remarks on the bus monitor and IP router
- 2 Help and support
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
PEAKnx YOUVI Basic Lighting Management Software Owner’s Manual
Legal notes
Product | Item number |
---|---|
YOUVI Basic | PNX31-10001 |
ETS-Import: https://cavok.peak-group.de?embedKey=0vk5Dl
Setup: https://cavok.peak-group.de?embedKey=Q1rHer
The product names mentioned in this document may be brands or registered
trademarks of their respective owners. These are not explicitly labeled with
“™” or “®”.
© PEAKnx GmbH Otto-Röhm-Strasse 6964293 Darmstadt Germany
www.peaknx.com
info@peaknx.com Document version: 4.1.3
1Who is this guide for?
This guide is intended for system integrators and describes the procedure recommended for setting up multiple panels in a project.
2 Recommended procedure for the YOUVI setup
Note: When you install the YOUVI software package, the USB-Connector
programs “PEAKnx Bus Monitor” and “PEAKnx IP Router” are automatically
uninstalled. These are now included in the YOUVI software and can be accessed
via YOUVI Dashboard or the page KNX > KNXnet/ IP-Router after startup.
Note: YOUVI requires network and Internet access during the first
startup to obtain an IP address and to load the visualization or further add-
ons. After that, no Internet connection is required to function, but only to
install updates.
Recommended procedure: with Windows PC
- Installation of the YOUVI Server and Visu on the panel with KNX access
- Installation of the YOUVI Client and Visu on the Windows PC
- Make basic settings in the configuration menu
- Check the imported project (via visualization on the PC) and create additional functions
- Optional: Install and set up add-ons
- Create a server backup
- Create the dashboard for the panel
- Create a client backup
- Transfer the backup to the panel
- Create additional dashboards and transfer their backups to additional client panels
Procedure without Windows PC
- Install YOUVI server and Visu on the panel with KNX access
- Make basic settings in the configuration menu:
- Enter “http://x.x.x.x:31228” in the browser to reach the configuration menu of the
- Where “x.x.x.x” must be replaced by the local IP address of your PEAKnx touch This is shown to you in the server overview, chapter 2.1. picture, pos 3).
- Check the imported project and create additional functions: Use software such as Anydesk or Teamviewer to set up the visualization on the
- Optional: Install and set up add-ons
- Create a server backup
- Create the dashboard for the panel
- Create a client backup
- Create additional dashboards on further client panels and make a client backup of
2.1 Installation of the YOUVI Server and Visu on the panel with KNX
access
- Transfer your KNX project to the
- Open the “YOUVI.Autostart” file on the desktop of the
- Select Installation and under “Setup Wizard”: Install
- Select the option “install YOUVI Server” and upload your ETS
Note: Be careful not to use spaces or special characters in the project name to avoid proces- sing errors.
- Right-click or long press on the house icon in the right area of the taskbar and open the YOUVI Dashboard program overview (1). You are now in YOUVI Configuration.
If YOUVI Dashboard is grayed out, check the panel’s network connection and restart it. If this does not help, connect manually via 3) Select YOUVI.
-
Program overview and access to YOUVI Basic software add-ons and their installation
-
Panel settings (overview of Controlmicro sensors and ambient light)
-
Server selection for the YOUVI client
-
YOUVI program help
-
Open the Dashboard page and go to “Install visualization”.
The visualization is installed.
2.2 Installation of the YOUVI Client and Visu on the Windows PC
- Carry out the steps from point 1, but this time select “install YOUVI Client” during the installa- tion and, if necessary, select the appropriate server from the list.
- After the installation, you can access the configuration by clicking on the green house in the taskbar or using your browser: Enter “http://x.x.x.x:31228” into the input field, where “x.x.x.x” must be replaced by the local IP address of your PEAKnx touch This is shown to you in the server overview, chapter 2.1. picture, pos 3).
- Now install the visualization here as well by clicking on “Install Visualization” on the Dashbo-
ard page.
2.3 Make basic settings in the configuration menu
- The default language in YOUVI Configuration after installation is
- On the General page, assign a specific name for the YOUVI
- On the Controlmicro, change the page using the menu in the upper right corner:
2.1Check the imported project and create additional functions
Information on ETS project preparation
When using YOUVI, the visualization of your KNX project is set up without
further confi- guration. Your ETS project will be read out by YOUVI and the
visualization will be created automatically. However, eliminating the
configuration level makes it all the more important to clearly define all the
group objects (GOs) in your ETS project so they can be recognized by YOUVI.
Therefore, please note the following points:
-
Work with the ETS 5 or
-
Place control devices, such as switches or push buttons, in the rooms in which the KNX devices are supposed to be
-
Create a control cabinet in the rooms for the sub-distribution.
-
Group address names are used in YOUVI as the device name, so name them understanda- bly, for example: “1st floor living room ceiling light (s)”.
-
Name group addresses of a device similar and only add a word or letters at the end to distinguish them, such as “feedback”, “switch”, or These additions will be filtered out by YOUVI and will not appear in the visualization.
-
Use the table in YOUVI Program Help > FAQs > Tips for your ETS project, to make devices recognizable for YOUVI. Here you can see which group objects must be at least present at the actuators for device identification.
-
Define active feedback for the
-
Export the project as a knxproj
Note: When creating a new project, it is recommended to use the project wizard of the ETS.
-
On your PC, select the red icon above “Visualization” on the Dashboard
The visualization opens on the Settings page. -
In _Settings > Connection Settings _you can see which YOUVI server you are connected Red font indicates a connection. Select the desired server and click the check mark if there is no connection to a server yet. In special cases, you can also add the YOUVI server manually by selecting “Add” and entering the IP address of the device.
-
Enable the Edit
-
Switch to the building overview by selecting the house icon on the bar on the left (Controlmi- cro in portrait format: below).
-
The imported project is shown in the
-
In the “Unassigned devices” room you will find all devices that YOUVI could not clearly assign to a
Note: In case of problems in the visualization, you can find the
YOUVI program help under Settings > About YOUVI Visu.
Verify name, device type, room assignment, and group addresses at each
device tile:
- To do this, go to the cogwheel of the desired tile and go through all pages of the tile
Note: If the project import did not work as expected, you will find more information in the info- box at the beginning of Chapter 2.4 on preparing the ETS project. In YOUVI Configuration > General > Projects, you can update, delete and re-upload KNX projects.
- Device tiles can also be moved to other rooms by drag & drop (only on panels in landscape format), as well as within the room
After all existing device tiles have been checked, you can create additional devices and functi- ons manually:
- Via the Add button in the building overview, the following functions are possible:
- Create new devices, scenes, group functions and building parts
2.1 Optional: Install and set up add-ons
To use add-ons permanently, a license must be purchased once. Additional functions available to you include a logic editor, IP camera widgets, Alexa voice control or the Netatmo bridge. The latest add-ons can be found on the YOUVI Configuration Dashboard page. For more informa- tion on how to set up the add-ons, see the program help topics “Modules” or “Bridges”.
2.2Create a server backup
- When all device tiles of the visualization have been checked and additional functions and add- ons have been set up, perform a central
- In YOUVI Configuration on the _General > General _page, you will find the item “YOUVI Server ” Click on the “Backup” button.
The central backup is created
2.3 Create the dashboard for the panel
The dashboard of the visualization is giving you an overview of your favorite functions. To crea- te it, the most important functions are simply “pinned” to it.
- Adjusting the scaling
- If you want to recreate exactly the same tile arrangement as on the panel on your PC, adjust the scaling as follows:
Panel | Resolution | Scaling | **Size in tiles*** |
---|---|---|---|
Controlpro | 1080 x 1920 | 125% | 5 x 2.75 |
Controlmini | 1080 x 1920 | 150% | 4 x 2.25 |
Controlmicro | 1200 x 900 | 200% | 2.75 x 2 (portrait format) |
- 1 corresponds to the largest tile size (square), 5 to the medium tile size, and 0.25 to the smallest tile size.
- The advantage of adjusting the scaling is that the tile arrangement is preserved after the transfer to the panel.
- Create the Dashboard
- Switch back to the
- Go through the rooms and select the dashboard icon on each tile to add it to the
- The group tiles on the trades page can also be added to the
- The dashboard icon next to the room name, adds the room to the
- Now switch to the dashboard
- Expand tiles by using the arrow icon on each In some cases, expanding the tile also gives you additional functions. This is the case for heating, blinds, weather station or room buttons.
- On the dashboard you move the tiles by drag & drop to any
- The grid always fills from left to To realize gaps on your dashboard, use placeholders, “+ placeholder”.
- You can create up to 5 different dashboard pages, each with a choice of 3 dashboard
- If you have IP cameras set up, add a camera widget using “+ Camera”.
- To add web pages to your dashboard, select “+ Web Widgets”.
- At the end, turn off the Edit mode
- Under _Settings > YOUVI Settings _you can additionally select temperatures for the title bar as well as the theme of the
2.4 Create a client backup
- Under _Settings > YOUVI Settings _you will find the item “Backup”. Click on “Save”. The backup of the visualization is created.
- Further information on backups can also be found in the program
2.5 Transfer the backup to the panel
- Transfer the backup file created in chapter 8 to the panel, e.g., via Team Viewer or USB flash drive.
- Open the visualization on the panel, either via the Dashboard page in YOUVI Configuration or by typing “Visu” in the Windows input
- Connect to the appropriate
- Under _Settings > YOUVI Settings _scroll down to “Backup” and select “Load”. Select the back- up
- Now click “Activate” under “Autostart” to open the visualization automatically even after a
restart.
2.6 Create additional dashboards and transfer their backups to additional
client panels
- Perform steps 7 to 2.9 analogously for additional client panels.
1Establish a connection to the KNX network
Note: YOUVI cannot be used with KNX/USB-Connectors or KNX/IP routers from third-party manufacturers.
Make sure the device running YOUVI has a KNX connection. In case of a PEAKnx touch panel, the connection can be established directly via the KNX port. If you have YOUVI installed on a Windows device the PEAKnx USB-Connector is to be used. The KNX Status in YOUVI Configu- ration shows you if a KNX connection could be established.
- After the YOUVI installation, the KNX Status should show “Connected”, as shown in the
- If the KNX connection cannot be established, go to _KNX > KNX Connection _in YOUVI Configu- ration and connect manually to the displayed
- In the case of the Controlmini and Controlpro (PNX11-20001/-2/-3), two KNX interfaces are in- dicated, as they also have 2 terminals. Try connecting to the other interface if the connection fails over the first one.
4 Remarks on the bus monitor and IP router
1 Remarks on the bus monitor and IP router
The bus monitor and IP router need no further configuration and are ready for
immediate use. The bus monitor for displaying and processing bus telegrams can
be accessed via the Dashbo- ard page in YOUVI Configuration. The IP
router controls the communication between the KNX bus and the connected
devices in your LAN (computers, tablets, smartphones). It can be found in the
menu item KNX > KNXnet/IP-Router .
Note: If you want to operate more than one KNX-IP router in the
same KNX network, the multi- cast addresses must be different. If they both
communicate over the same multicast address, this will result in a circulating
message
2 Help and support
Further information can be found in the YOUVI-Program-Help. If you have any problems, please contact our support:
- Mail: support@peaknx.com
- Phone: +49-6151-279 1825
Read More About This Manual & Download PDF:
References
- cavok.peak-group.de?embedKey=0vk5Dl
- cavok.peak-group.de?embedKey=4MLBhM
- cavok.peak-group.de?embedKey=8bDyrH
- cavok.peak-group.de?embedKey=Q1rHer
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>