STILFER 527151 Ceramic Glass Boiling Units Instructions
- June 9, 2024
- STILFER
Table of Contents
STILFER 527151 Ceramic Glass Boiling Units
Product Information
The product is a ceramic-glass boiling unit that requires proper installation, use, and maintenance. It is available in two models, 527.151 and 527.152. The user manual provides instructions in multiple languages, including Dutch, French, and German. The technical data and installation instructions are mentioned in the manual, along with legal requirements, electrical connection,unipotential setup, and other relevant information.
Product Usage Instructions
Installation
- Position the equipment using a spirit level and adjust the legs accordingly.
- The main switch or power outlet should be placed near the equipment in an easily accessible location.
- Place the machine under an exhaust hood to quickly remove fumes.
- Ensure that the machine is placed only near fire-resistant walls or kitchen furniture.
- Strictly adhere to fire safety regulations.
Technical Requirements
-
The installation must comply with current accident prevention
laws and CEI installation standards. -
The equipment must be connected to a unipotential system.
-
Do not connect the equipment to a non-unipotential system.
-
Clean the machine thoroughly before installation.
Usage Instructions
- Use the appliance under supervision only.
- Do not place the machine near fire-resistant walls or partitions (minimum distance of 3 cm).
- Remove all plastic protective film before using the equipment.
- Clean the parts thoroughly to remove any adhesive residue using non-abrasive and non-corrosive products.
Maintenance
- Only qualified personnel should perform maintenance on the equipment.
INSTRUCTION FOR USE
TECHNICAL DATA
The data plate is near power cable, on the back of the machine and lists
all the data needed for connecting up to the mains.
INSTALLATION
- The equipment must be positioned using a spirit level and adjusting the legs (screw/unscrew).
- The main power switch or power outlet must be near the equipment in an easily accessible position.
- We recommend installing the machine under an extractor hood so that vapours can be removed rapidly. The machine should only be placed near walls, partitions or other kitchen furniture that are made of flameproof materials.
- Fire regulations must be strictly adhered to.
Legal requirements
Installation must be to the following standards:
- current accident prevention laws;
- CEI installation standards.
Installation
Installation, set-up and maintenance must be carried out by qualified
personnel. All installation work must be done in compliance with current
regulations.
The manufacturer will accept no liability in relation to faulty operation due
to defective or non compliant installation.
WARNING: As required by international law, the equipment should only be
connected up to the mains if there is a omnipolar circuit breaker upstream
with a contact opening of at least 3 mm.
Electrical connection
- The equipment is supplied with a power cable.
- If you have to replace this cable, make sure you use a cable that its cross section is sufficient for the equipment’s power rating.
- To change the cable, pass it through the cable lead and connect the wires to the terminal block, which is located in the cable lead on single phase machines and inside the equipment on three-phase
Unipotential
- The equipment must be connected to a unipotential system.
- The connection screw is located in the rear of the housing and marked by the sign WARNING! The manufacturer accepts no liability and will not refund under guarantee any damage caused through installation that is improper or not compliant with the instructions.
Set up: The machine must be carefully cleaned ( see section 4: Cleaning)
INSTRUCTIONS FOR USE
WARNING; never use the equipment unless under supervision.
Don’t place the machine near walls or partitions that are made of flameproof
materials (distance min. 3 cm.). Remove all plastic adhesive parts before
using the appliance .Clean parts throughly to remove all adhesive residue
(don’t use abrasive substance) .
Power up
- Connect the plug in one wall socket earthed .
- Heat is regulated by a thermostat that permit to choose the desired temperature .
- To regulate temperature you should turn the knob in the clock direction ½ rotation , so the central side start . To heat the entirely top, included the exterior side, turn the knob over the maximum sign and let it go.
- Now the whole top is working at the maximum power.
- To switch off the appliance turn the knob back to “0”.
CLEANING
WARNING: during cleaning, do not wash the outside of the machine with direct or high-pressure jets of water. Clean the equipment carefully at the end of work every evening. Daily cleaning of the equipment guarantees perfect operation and long life. Power down the equipment before cleaning it and let it cold. Use a sponge and liquid detersive , rinse with water and dry with soft cloth . Do not use abrasive and or corrosive products.
- What to do after long period of inactivity
- Carefully clean and dry the equipment as explained in the instructions and power down.
- What to do in the event of failures
- In the event of a failure, switch off the machine, disconnect the power and call customer service.
MAINTENANCE
All maintenance work must be done by qualified personnel.
Access
- To access all the electrical parts ( thermostats, connections, resistance, etc.), open the bottom of the machine .
- The Manufacturer will accept no liability if the instructions in this booklet are not followed or if tampering by unqualified personnel is discovered.
Code| Model| Plate| Volts| kW| Dimensions
Masse mm.
| Weight Poids
---|---|---|---|---|---|---
0104| Vulcano| 320×320| 230/2| 2,1| 415x415x105| 6
0105| Stromboli| 320×320| 400/2 N| 21, x 2| 785x415x105| 11