Gre RBR75 Wet Runner Electric Pool Robot Instruction Manual

: June 9, 2024
: Gre

RBR75 Wet Runner Electric Pool Robot

Gre RBR75 Wet Runner Electric Pool Robot Instruction Manual-
PRODUCT

Product Information:

Product Name: RBR75
Manufacturer: www.grepool.com
Type: Electrical Pool Cleaner Robot
Function: Cleans the bottom of the pool by collecting rubbish and debris through a bottom filter cabine
Features: Rotation jet head at the upper cover, lithium battery, cartridge filter, charger
Safety Precautions: Follow the basic safety precautions while installing and using the product. Use the original charger provided only. Do not disassemble the robot without professional guidance or notice from the authorized distributor or manufacturer. Do not leak the lubricant oil, and it causes water polluted. Stop working the cleaner when there is anything wrong; Please contact with the authorized distributor or replace it with original parts/accessories.

Product Usage Instructions:

Charging: Remove the pin cover and plug the charger into the charging port to start charging. Once the robot starts charging, the indicator light on the external adapter will turn red. When the robot is fully charged, the indicator light will turn green. After charging, put the pin cover back on the charging port. Make sure that the pin cover is fully sealed before submerging in the water.
Power On: Turn on the switch. The indicator light will be displayed. Adjust the length of the rope to ensure that it is at the same height as the water level, and the extra length of the rope is tied back or cut off. Loosen the rope on the floater, put the robot horizontally into the pool and wait for it to sink to the pool bottom. It takes around 20-30 seconds for the air to be piped out. When the robot has no power, it will automatically stop at the edge of the pool (it may also get stuck in the middle of the pool due to obstacles).
Garbage Disposal: Ensure that the filtration system is turned off as the water circulation in the pool may affect the robot’s motion mode. Any obstacle in the swimming pool such as a ladder will affect the robot’s crawling and cleaning track. If using a brine tank, make sure that all the salt is dissolved before putting the robot into the water.

SAFETY WARNING

When installing and using this electrical equipment, you should always follow the basic safety precautions. Please read the following carefully.

WARNING
The robot is not a toy, and is operated by people older than 8 years age. Any people who operates the cleaner, has to read the manual carefully before work it.

Cleaning and user maintenance shall not be made by children without supervision.
The robot is designed to clean the swimming pool.
Please use the original batteries and charger when using.
Only charging it when the robot is power off.
Put the robot into a clean and dry place. Do not expose it under the sun, or close to explosive.
The robot automatically stops to work when it is out of water.
Do not close to the vacuum head when it is working, due to its suction power, especially for the human body, animals, hairs or clothes.
Do not disassemble the robot without professional guidance or notice from the authorized distributor or manufacturer.
Do not leak the lubricant oil, and it causes water polluted.
Stop to work the cleaner when there is anything wrong; Please contact with the authorized distributor or replace it to the original parts/accessories.
Robot working conditions:
Maximum applicable water depth: 3 m (10 ft)
Water temperature: 4°C( 39.2°F )-35°C( 95°F )

Charger

Use the original charger provided only.
For indoor use only. The charger should not be used outdoor and not be exposed to rain, humidity, any liquid or heat.
Keep the charger out of children.
Never use the charger if any damage is found.
Do not handle the cleaner and charger with wet hands and bare feet, when charging the robot.
Disconnect the charger from power when not in use.
If the wire is damaged, it must be replaced by a new charger to avoid danger.
Make sure the cleaner and charger are totally dry before charging.
Charge the robot 5 hours prior to the first use. Normally cleaner can be operated about 75 minutes after fully charged.

Battery disposal

The robot battery is a lithium battery, it must be disposed properly, please contact with your local authority for more information.
Never attempt to disassemble the lithium battery.
Remove all personal items such as rings, bracelets, necklaces and watches when unwiring a lithium battery from the vacuum unit.
The battery causes short curcuit current, as well as severe burning when it is high enough.
Wear complete eye protection, gloves and protective clothing when removing the battery pack.
No smoking or sparkling flame near the robot , or, it may causes unknow gases.
If acid comes in contact with skin and clothing, wash immediately with plenty of soap and water.
If acid comes in contact with eyes, immediately flood eye with running cool water for at least 15 minutes. Get medical attention immediately.

Above warning and cautions are not intended to incorporate all possible instances for risks and/or severe injury. Pool owners should always exercise intensive caution and common sense when operating the robot.

ASSEMBLY

A: Floater
B: Upper cover
- B-1: Jet head
C: Cartridge filter
D: Filter
E: Bottom base
F: Charger

There is a rotation jet head at the upper cover, the water is passing from bottom to the jet head to make the robot moving. While facing obstacle, the jet head turns around 180 degrees, the robot rounds the obstacle and moving by another line. The rubbish is collected and installed by the bottom filter cabine.

ASSEMBLY AND OPERATION

Charging warning:

Only use the external adapter and the charging cable provided.
Make sure that the robot and charger ports are clean and dry before installation.
Power up the robot before using it for the first time (about 5 hours)

Take the pin cover off before charging.
Plug the charger into the charging port, then start to charge.
Note: Once the robot starts charging, the indicator light on the external adapter will turn red. When the robot is fully charged, the indicator light will turn green.
After charging, put the pin cover back on the charging port. Make sure that the pin cover is fully sealed before submerging in the water.

POWER ON

Turn the switch on. The indicator light will be displayed. Loosen the rope on the floater, put the robot horizontally into the pool and wait for it to sink to the pool bottom. It takes around 20-30 seconds for the air to be piped out.
Adjust the length of the rope to ensure that it is at the same height as the water level, and the extra length of the rope is tied back or cut off.
When the robot has no power, it will automatically stop at the edge of the pool (it may also get stuck in the middle of the pool due to obstacles).
Note:
It is recommended that the filtration system be turned off as the water circulation in the pool may affect the robot’s motion mode.
Any obstacle in the swimming pool such as a ladder will affect the robot’s crawling and cleaning track.
If you are using a brine tank, make sure that all the salt is dissolved before putting the robot into the water.

GARBAGE DISPOSAL

Gre RBR75 Wet Runner Electric Pool Robot Instruction
Manual-FIG-5

MAINTENANCE AND STORAGE

The battery discharges itself during storage. Make sure the robot is fully charged before storage.
When not in use, you must recharge the battery at least every three months.
- Unplug the external adapter from the socket and then the charging cable from the external adapter and the robot.
- Remove the attachment from the robot. If necessary, rinse the robot and accessories with clean water. Do not use detergent.
- Before storage, make sure the robot is drained.
- Use a wet cloth to clean and dry the robot and its accessories.
- Store in a well ventilated place away from sunlight, heat, fire sources, pool chemicals and children.
- The storage environment temperature should be 10ºC – 25ºC (50 °F – 77°F ).
  Note: higher storage temperatures may shorten battery life.

Maintenance and replacement of impeller:
Recommended tool (not included): screw driver Gre RBR75 Wet Runner Electric
Pool Robot Instruction Manual-FIG-6

Maintenance and replacement of the wheels:

Note: the main wheel on this side has magnets. Please contact your dealer for spare parts or maintenance work.

BATTERY ASSEMBLY AND REPLACEMENT

Do not treat electrical appliances as unclassified municipal waste. Use separate collection facilities. For information on available collection systems, contact your local authorities.

Do not remove the lithium battery without authorization.
When removing the lithium battery from the vacuum device, please remove any rings, bracelets, necklaces or watch that your are wearing.
The short-circuit current generated by a battery is enough to suck up rings (or similar items), which can cause severe burns.
Before removing the battery pack, please wear eye protection, gloves and protective clothing.
Be careful not to touch the wire or any metal parts, as this can cause sparks or a short circuit.
Do not smoke or light naked flames near the robot, as this can set the battery on fire and give off gas.
Avoid exposing the battery to fire or high temperatures, as this could cause an explosion.

Note!
If the battery leaks, avoid contact with the damaged battery and put it in a plastic bag.
If skin or clothing comes into contact with acid, wash immediately with plenty of soap and water. If the eyes come into contact with acid, rinse them with water for at least 15 minutes and seek treatment from a doctor.

Battery replacement:

Note: User must consult dealer before any battery replacement.

Pull the four clips out of the core part of the upper cover outwards, remove it from the body assembly of the bottom cover and take out the micro-particle filter.
Use a screwdriver to remove all screws on the power cover of the bottom cover.
Open the battery cover, find the battery connection line, press the clip on the connector, pull it out and take out the battery.
Follow the steps for disassembly to re-install the battery and assemble the charging components.

Note:

If there are impurities in the seal ring, clean it and put it back into the seal ring groove.
Make sure that the components are reassembled in the right direction. The six screw holes must be aligned to lock the screws.

Note: wrap the connector with insulating tape immediately to avoid a short circuit caused by two wire terminals coming into contact with each other.

TROUBLESHOOTING

If you have problems with your cleaner, follow the troubleshooting steps below to restore performance. Note: turn off the power before making any repairs. Gre RBR75 Wet Runner Electric Pool Robot Instruction Manual-
FIG-10 Gre RBR75 Wet Runner
Electric Pool Robot Instruction Manual-FIG-11

GUARANTEE CERTIFICATE

GENERAL TERMS

In accordance with these provisions, the seller guarantees that the product corresponding to this guarantee (“the Product”) is in perfect condition at the time of delivery.
The Guarantee Term for the Product is two (2) years from the time it is delivered to the purchaser.
In the event of any defect in the Product that is notified by the purchaser to the seller during the Guarantee Term, the seller will be obliged to repair or replace the Product, at his own cost and wherever he deems suitable, unless this is impossible or unreasonable.
If it is not possible to repair or replace the Product, the purchaser may ask for a proportional reduction in the price or, if the defect is sufficiently significant, the termination of the sales contract.
The replaced or repaired parts under this guarantee, will not extend the guarantee period of the original Product, but will have a separate guarantee.
In order for this guarantee to come into effect, the purchaser must provide proof of the date of purchase and delivery of the Product.
If, after six months from the delivery of the Product to the purchaser, he notifies a defect in the Product, the purchaser must provide proof of the origin and existence of the alleged defect.
This Guarantee Certificate is issued without prejudice to the rights corresponding to consumers under national regulations

INDIVIDUAL TERMS

This guarantee covers the products referred to in this manual.
This Guarantee Certificate will only be applicable in European Union countries.
For this guarantee to be effective, the purchaser must strictly follow the Manufacturer’s instructions included in the documentation provided with the Product, in cases where it is applicable according to the range and model of the Product.
When a time schedule is specified for the replacement, maintenance or cleaning of certain parts or components of the Product, the guarantee will only be valid if this time schedule has been followed.

LIMITATIONS

This guarantee will only be applicable to sales made to consumers, understanding by “consumer”, a person who purchases the Product for purposes not related to his professional activities.
The normal wear resulting from using the product is not guaranteed. With respect to expendable or consumable parts, components and/or materials, such as batteries, light bulbs, etc. the stipulations in the documentation provided with the Product, will apply.
The guarantee does not cover those cases when the Product; (I) has been handled incorrectly; (II) has been repaired, serviced or handled by non- authorised people or (III) has been repaired or serviced not using original parts. In cases where the defect of the Product is a result of incorrect installation or start-up, this guarantee will only apply when said installation or start-up is included in the sales contract of the Product and has been conducted by the seller or under his responsibility.

CROSSED-OUT WASTE CONTAINER

In order to reduce the amount of waste of electric and electronic apparatus, to reduce the danger of components, to encourage the reuse of apparatus, to assess waste and to set up a suitable waste treatment system, with the aim of improving the efficiency of environmental protection, a set of rules has been established applicable to the manufacture of the product and other rules regarding the correct environmental treatment when these products become waste.
It is also intended to improve the environmental practices of all agents involved in electrical and electronic goods, including manufacturers, distributors, users and particularly those directly involved in the treatment of waste derived from these apparatus.
From 13th August 2005, there are two ways of disposing of this apparatus:
If you purchase a new equivalent apparatus or which has the same functions as the one you wish to dispose of, you can hand it over, free of charge, to the distributor when making your purchase.
You can take it to local collection points.
We shall cover waste treatment costs.
The apparatus are labelled with a symbol of a “crossed-out waste container”. This symbol means that the apparatus is subject to selected waste collection, different from general waste collection.
Our products are designed and manufactured with top-quality, environmental-friendly materials and components, which can be reused and recycled. In spite of this, several parts of this product are not biodegradable and therefore it should not be left in the environment. For the correct recycling of this product, please completely detach the electrical motor from the rest of the filtration equipment.

If You Have Any Problem, Contact Us!
www.grepool.com/en/after-sales

DISTRIBUTED BY
MANUFACTURAS GRE, S.A.
ARITZ BIDEA Nº 57 BELAKO
INDUSTRIALDEA, APARTADO 69 48100 MUNGUIA

We reserve the right to change all or part of the articles or contents of this document, without prior notice

EU DECLARATION OF CONFORMITY

The undersigned
Manufacturas GRE S.A.
Aritz Bidea nº57,
Belako Industrialdea,
Apdo 69,
48100 Mungia (Bizkaia) Spain.

Declares under its sole responsibility that the products: