emwicon WMX7203-F WiFi 6E BT 5.2 Mini PCIe Module User Guide
- June 9, 2024
- emwicon
Table of Contents
- emwicon WMX7203-F WiFi 6E BT 5.2 Mini PCIe Module
- Product Overview
- Packaging Contents
- Installation Guide
- Frequency
- Federal Communication Commission Interference Statement
- Overview
- Packaging
- Product Installation guide
- Federal Communication Commission Interference Statement
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
emwicon WMX7203-F WiFi 6E BT 5.2 Mini PCIe Module
Product Overview
The Wi-Fi 6E BT 5.2 Mini PCIe Module is a wireless LAN card that contains a Qualcomm chip for wireless applications. It supports key security features such as Wi-Fi Protected Access (WPA), WPA2, WEP, and 802.1x. The card is typically used for integration into other wireless products such as AP/Router and should be kept at a distance of 20 cm away from the human body.
Packaging Contents
The package contains one Wi-Fi 6E BT 5.2 Mini PCIe Module.
Installation Guide
- Shut down the power of the platform.
- Align the Wi-Fi 6E BT 5.2 Mini PCIe Module with the Mini PCIe Type socket on the platform.
- Adjust and push down the Wi-Fi 6E BT 5.2 Mini PCIe Module gently until the metal locking levers on the Mini PCIe type socket are latched. (Please take note that the Wi-Fi 6E BT 5.2 Mini PCIe Module can only fit in one direction due to the keyed notch. Wrong orientation will cause improper installation and may damage the Mini PCIe Type socket).
- Connect the antenna(s) on the Wi-Fi 6E BT 5.2 Mini PCIe Module.
- Reboot the platform.
- Install drivers if necessary.
Frequency
The Wi-Fi 6E BT 5.2 Mini PCIe Module operates on the following frequencies:
- 2400 ~ 2483.5 MHz
- 2402 ~ 2480 MHz
- 5150 ~ 5850 MHz
- 5850 ~ 5895 MHz
- 5925 ~ 7125 MHz
The connector is I-PEX MHF1 PLUG.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
To reduce interference, the following measures can be taken:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and the user’s body.
Usage Conditions
This module is intended for OEM integrators only. It has been tested for compliance with FCC Part 15 regulations and for standalone mobile RF exposure use conditions. If used in any other conditions, such as co-location with other transmitters or being used in a portable condition, a separate reassessment through a class II permissive change application or new certification is required.
Overview
The devices Wi-Fi 6E BT 5.2 Mini PCIe Module contain a Qualcomm chip for
Wireless LAN applications. Wi-Fi 6E BT 5.2 Mini PCIe Module support key
security features like Wi-Fi Protected Access (WPA), WPA2, WEP, 802.1x.
Typical application of the card is integration into other wireless products
such as AP/ Router which is used distance 20 cm away human body.
Packaging
The package contains the following item(s):
1 x Wi-Fi 6E BT 5.2 Mini PCIe Module
Product Installation guide
- Shut down the power of the platform
- Align the Wi-Fi 6E BT 5.2 Mini PCIe Module with the Mini PCIe Type socket on the platform
- Adjust and push down the Wi-Fi 6E BT 5.2 Mini PCIe Module gently until the metal locking levers on the Mini PCIe type socket is latched. (Please take note that the Wi-Fi 6E BT 5.2 Mini PCIe Module can only fit in one direction due to the keyed notch. Wrong orientation will cause improper installation and may damage the Mini PCIe Type socket)
- Connect the antenna(s) on the Wi-Fi 6E BT 5.2 Mini PCIe Module
- Reboot on the platform
- Install drivers if necessary
Frequency
- 2400~ 2483.5 MHz
- 2402 ~ 2480 MHz
- 5150 ~ 5850 MHz
- 5850 ~ 5895 MHz
- 5925 ~ 7125 MHz
- Connector: I-PEX MHF1 PLUG
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
This device meets all the other requirements specified in Part 15E, Section
15.407 of the FCC Rules.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module:
KDB 996369 D03 OEM Manual v01 rule sections:
-
List of applicable FCC rules
This module has been tested for compliance to FCC Part 15 -
Summarize the specific operational use conditions
The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification. -
Limited module procedures
Not applicable. -
Trace antenna designs
Not applicable. -
RF exposure considerations
This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. -
Antennas
The following antennas have been certified for use with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users. -
Label and compliance information
The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2A3G3-WMX720X”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met. -
Information on test modes and additional testing requirements
This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification. -
Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable.
As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the
Host and Module. The final product must be reassessed against all the
essential requirements of the FCC rule such as FCC Part 15 Subpart B before it
can be placed on the US market. This includes reassessing the transmitter
module for compliance with the Radio and EMF essential requirements of the FCC
rules. This module must not be incorporated into any other device or system
without retesting for compliance as multi-radio and combined equipment.
Prohibited for control of or communications with unmanned aircraft systems,
including drones.
EmWicon Corporation
7F.-5, No. 258, Liancheng Rd., Zhonghe Dist. New Taipei City 235 Taiwan
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>