jetfi G40 4G Wireless Data Terminal User Manual
- June 9, 2024
- jetfi
Table of Contents
jetfi G40 4G Wireless Data Terminal
Product Overview
Product appearanc
- LED Indicator
- Volume
- Speake
- Secondary Microphone
- Touch display
- SIM Card Tray
- Power Button
- Type-C Port
- Charging Contact
- Microphone
Chargers with an Input: DC 5V ⎓ 2A are recommende
User Interface
- Device info
- Accumulated flow
- Number of device connections
- Battery level
- SIM card signal strength
- More info
- User Manager
Product Introduction
Brand : jetfi
Box Content : Device, User Manual, Type-C USB cable, OTG cable Receive
card pin
Note : Adapters (Charging) 100-240V~50/60Hz 0.15A are recommende
Technical Specification :
- LTE FDD : Band 2/4/5/7 /12/13/17/25/26/66
- LTE TDD : Band 41
- WCDMA : Band 2/4/5
- Max Upload Speed : 50Mbps
- Max Download Speed : 150Mbps
- Wi-Fi : 802.11 a/b/g/n/ac
- Screen Size : 5.0 inch
- Number of external SIM cards : one Nano SIM card
- Type-C USB
- Battery Capacity : 3,900mAh ( 3.8V 14.82Wh )
- Input : DC 5V 2A
- Size : 13672.212 mm
- Weight : 188 g (net)
*It is the theoretical value. The actual usage rate may vary based on local network environment and the coverage of the operator’s network.
Quick Start Guide
Step 1.Turn on the device
Press the power button for 3-5 seconds, once it’s on, the homepage of the device is shown as below:
*Picture for reference only. Actual product may vary.
Step 2.
Switch on Wi-Fi on smartphone, connect to the Wi-Fi network of the device
(Wi-Fi name is shown on the homepage), input the Wi-Fi password and enjoy the
internet once it’s connected
Powerbank Function
The OTG cable allows you use your G40 to charge a mobile phone. G40 can be used as power bank when it is powered on and has over 30% battery. If you have made sure you’ve got everything right, but find the G40 not charging properly. Here are 2 possible reasonS.
- The OTG cable is not recognized by device. Please try with the original charging cable of device:
- The OTG cable is not working. Please try with a new charging cable. If it still does not work, please contact customer service for warranty.
Local SIM Guide
- Local SIM is supported by device, which has one Nano SIM slot and one TF card Slot.
- Open the SIM card tray with a needle, and insert the SIM card as shown in the picture below. Please contact customer service if any issue encountered.
- Please remove the PIN of the SIM before you insert the SIM, as the SIMs with PIN are not supported by device.
APN Setting
Follow the steps below to set APN for local SIMs on device:
- Insert the local SIM, and select it in SIM Manager page;
- Then click “local SIM” on the list
- Click ‘Data Connection’ ;
- Click ‘Access Point Name (APN)’ to finish the settings
Warning
Specific Absorption Rate (SAR) information. SAR tests are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands, although these is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value, in general, the closer you are to a wireless base station antenna, the lower the power output.
Before a new device can be made available for sale to the publicity must be tested and certified by the FCC that it does noticed the exposure limit established by the FCC, Tests for each device are performed in positions and locations as required by the FCC. For body worn operation, this device has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains nonmetal and that positions the device a minimum of 1.0 cm from the body.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause.
Undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and complies with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, macaques harmful interference to radio communications. However, there is nonguaranteed that interference will not occur during installation. If the device does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is suggested to try to correct the interference by the following measures
Warning
–Reorient or relocate the receiving antenna.
–Increase the distance between the equipment and receiver.
–Connect the equipment to an outlet on a different circuit to the receiver.
–Consult the manufacturer or an experienced radio/TV technician for help.
Information on the disposal and
recycling of the device This symbol (with or without a solid bar) on the
device, batteries (if included),and/or the packaging, indicates that the
device and its electrical accessories(for example, a headset, adapter, or
cable) and batteries should not be disposed of as household garbage. These
items should not be disposed of as unsorted municipal waste and should be
taken to a certified collection point for recycling or proper disposal. For
detailed information about device or battery recycling, contact your local
city office, household waste disposal service, or retail store. Disposal of
the device and batteries (if included) is subject to WEEE. Directive Recast
(Directive 2012/19/EU) and Battery Directive (Directive2006/66/EC). The
purpose of separating WEEE and batteries from other waste is to minimize the
potential environmental impacts and human health risk of any hazardous
substances that may be present.
Jetfi Technology Co., Ltd
service@jetfi-tech.com
+886-2-2751-9338
www.jetfi-tech.com.tw
3F., No. 92, Sec. 5, Nanjing E. Rd,
Songshan Dist., Taipei City 105,
Taiwan(R.O.C.)
FAQ
How long does it take to fully charge the Dveice ?****
It depends on the electronic current. If you use the charger 2A to charge the phone, it will take four hours to get the phone full charged.
How long can it work continuously?****
Approximately 12 hours once fully charged
How many connections can it support at the same time?****
The Device can support up to 5 connections at the same time
How long does it take to connect to the internet once switched on?****
It depends on the local network condition, normally it will take 1-2 minutes.
If it is used for the first time in a country, it may take up to 5 minutes
Why the signal icon shows 3G even if the device supports 4G?****
The Jetfi service depends on the local operators’ network, the 4G network is prioritized. When the 4G signal is weak, the signal will be transferred to 3G.
What should I do if it stops responding?****
Press the power button for 18 seconds
What should I do if the local SIM doesn’t work?
Manually enter the APN of the SIM card (‘SIM Manger’ -> ‘APN settings’, manually enter the APN info of your SIM card and save.)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>