YENKEE YHP 3400 Wireless Gaming Headset User Manual
- June 3, 2024
- YENKEE
Table of Contents
YENKEE YHP 3400 Wireless Gaming Headset
OVERVIEW
- Headset
- Power/light mode button
- EQ button
- USB Type C port
- Microphone mute button
- Volume wheel
- Microphone port
- Microphone
- USB doongle
- USB A to USB C charging cable Im
- USB C to jack 3.5mm audio cable
Before first use, be sure to read the safety instructions contained in this user’s manual carefully. Before first use, please charge the headpho- nes to a maximum level.
Caution : To prevent damage to your hearing, before connecting the headphones to your mobile phone, make sure that your device’s volume level is always set to minimum.
Note : The headphones will turn off after a longer period of inactivity unless they are paired to another device.
First time connecting
Plug USB dongle into the USB port of device you like to connect your headphones with. lurn the headphones UN and wait for connection. While connection is in process LED backlit will flash green, once connection established LED backlite will change to RGB breathing mode. In case of problems with connection try to repeat process or get closer to dongle. Inter- ference of similar wireless devices in surroun- ding could also cause first time connection problems. Try to switch them off temporaly. For connecting with already paired device you simply plug USB dongle into the USB port and turn ON headphones.
Note : It is possible to have pair of YHP 3400 headphones connected to one doongle but it is not possible to have two dongles connected to one headphones.
Note : Check the audio settings in connected device. Make sure your audio input/output is set up to ,Wireless Audio” source.
Wired audio mode
If you prefer to use headphones with a cable audio transfer, use included audio cable (1). Tirn OFF headphones and than plug Type C Conector to headphones and 3,5mm jack to audio source device. During wired mode you will not be able to use EQ and LED backlit.
Microphone
Microphone can be muted by pressing MUTE button (5). Button pushed – MUTE ON Button unpushed – MUTE OFF To plug the microphone in, you should insert the microphone with the top notch area lined up with the lock icon. Plug in the microphone and then turn counter clockwise to lock it in place. When unplugging the microphone, do the above actions in reverse order.
EQ (equalizer):
Press the EQ button to charnge the different equalizer modes. 3 modes include:
HIFT|T beep), Bass [2 beeps, 30 3 beeps When you turn the headphones off, the
next time you turn it on last used E0 mode will be automatically adjusted.
Volume:
The volume wheel (6) is located above the microphone button. You can adjust
the valume by rotating the wheel up or down.
RGB backlit
Click the light mode button (2) shortly to cycle through the different backlit colors 8 Colorsinclude: Breathing all colors, Red, Green, Blue, Purple, Yellow, Turquoise, White, backlit off
Charging
Charging duration from empty to full charged is aprox. 2.5h. LED backlit will flash red while charging in process. Once headphones are fully charged LED backlit will change colour to a solid green colour. Headphones can be used during charging however they must be turned ON and audio transmission will be wireless. USB Type C plug is only for charging in this case. Any USB charger 5V DC/1A can be used for charging use only certificated and verified brands.
Power:
Turn ON by holding the power button (2) for 3 seconds. Turn OFF by holding the
power button [12) for 5 seconds. When the battery capacity drops to 10%, you
will be notified by 5 audio beep signals ans at the same time LED backlit will
start to flash in red colour. You should charge your headphones as soon as
possible because there is no more notifications after and your headohones
could turn OFF during important gaming sesion. Left time after low battery
notification depends on volume level and it will be longer with backlit turned
off. Wireless headset PANZER is compatible with PS4, PS5, most Xbox systems
(only wired connection with controller], Windows 7/8/10 and most of Mac 0S. A
charged battery provides power for 12-18 hours of operation at normal volume
levels. A high volume consumes more battery power therefore, we recommend
listening at normal Volume levels.
Caution : For charging, use only the original accessories supplied with the appliance. To achieve the maximum battery lifetime, it is best to start charging the battery after the low battery power notification. Charge continuOusly until fully charged. When the operating time of the battery becomes very short, the battery’s lifetime has been use up.
Recommendation : If your headphones are not to be used for an extended period of time, we recommend to fully charge the batteries once every two to three months. We recommend to store the headphones and the charging box with the battery charged to prevent irreparable damage to the battery loss of capacity
Specifikace
Charging voltage: DC 5V/1A [USB Type C) | Operating voltage: 3.7V | Charging time: 2.5 h Playback time with backlit: s12h | Playback time without backlit: s18h | Battery capacity: 1100mAh |Lithium polymer)| Latency:40ms| Working frequency: ISM Band |24GHz) Maximum transmitter power at 24 GHz – 24835 GHz: 32mW | Dperating range: <10m | Spea- kers diameter: 40mm | Frequency response: 20-25Khz | Sensitivity: 102dB | Impendance: 320 Microphone: omnidirectional [detachableJ | Mic. sensitivity: 40dB | Weight: 384g
System requirements:
USB port | Windows 7/8/10 | Mac 0S X
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>